Related Manuals for Edge Evolution 15051
Summary of Contents for Edge Evolution 15051
- Page 1 2004-2008 Ford F-Series 5.4L & 4.6L Triton V8 Edge Evolution Programmer Installation Instructions & Manual P/N: 15051 READ IMPORTANT SAFETY INFORMATION IN THIS MANUAL...
-
Page 2: Table Of Contents
Evolution FORD 4.6 and 5.4 Liter TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION ___________________________________ 3 SAFETY TERMS ___________________________________________________________ 3 SAFETY GUIDELINES ______________________________________________________ 3 PRODUCT REGISTRATION _____________________________________________ 4 Benefits of product registration: _______________________________________________ 4 CARB/EPA Compliance __________________________________________________ 5 About the Evolution _____________________________________________________ 6 Stock Program ______________________________________________________________ 6 Transmission or Economy Only Program _______________________________________ 6 Tow Performance Program (87+ octane fuel)_____________________________________ 7... - Page 3 Recommended Dyno Procedure ___________________________________________ 38 Troubleshooting/Tips ___________________________________________________ 39 Warranty Information___________________________________________________ 41 LIMITED 1 YEAR WARRANTY _____________________________________________ 41 Commonly Used Acronyms_______________________________________________ 43 Technical Support: _________________________________________________________ 43 ©2000 Edge Products All rights reserved. Edge Products 1080 South Depot Dr. Ogden, UT 84404 1-888-360-3343 www.edgeproducts.com...
-
Page 4: Important Safety Information
The Edge product you have bought is a high-performance product. As such, it does present some risks of which you should be fully aware. Do not use this product until you have carefully read all the following safety information and the Owner Agreement. -
Page 5: Product Registration
Enhanced Features – almost all Edge products are easily updated via the internet. We are constantly adding new features and improvements to our product that we know you will want to enjoy ... -
Page 6: Carb/Epa Compliance
Evolution is NOT RECOMMENDED as it may cause an excessively lean condition which could result in engine damage. Edge Products will not be responsible for any damages caused by using the Evolution on a vehicle that has been modified from a stock configuration. -
Page 7: About The Evolution
The purpose of the sticker is to inform anyone who may have questions regarding the use of your Edge product and how it affects emissions. For example, it would be something to show an emissions technician if questioned when taking your vehicle in for an emissions check to let him/her know the product is CARB emissions compliant. -
Page 8: Tow Performance Program (87+ Octane Fuel)
Evolution FORD 4.6 and 5.4 Liter Tow Performance Program (87+ octane fuel) This setting not only provides improved transmission shifting, but will also modify the ignition timing and fuel injection strategies to improve the performance of your vehicle. This level is designed to run with 87 octane fuel, although you may realize additional benefits by running 89 octane (or better) fuel. -
Page 9: Pids (Parameter Id)
Do not use the Performance Tests feature to break any WARNING traffic laws. Perform these tests only where they are legal and safe. Another feature often only found on the Edge Product monitors, is the ability to determine your quarter mile times as well as your 0-60 times. Alerts If you would like to know when a certain parameter, such as transmission temperature, reaches a desired value you can set an alert to that value. -
Page 10: Custom Options
Evolution FORD 4.6 and 5.4 Liter Custom Options While programming your vehicle, you have the option to customize our tuning. For example, you can change your tire size value which can correct your odometer readings that result from changing tire sizes. Refer to the Custom Options section for a complete list and description of options that are available. -
Page 11: Getting Connected
Ford 4.6 and 5.4 Liter Evolution Getting Connected The Evolution programmer connects to the diagnostic port of your vehicle. Follow these steps to install the Evolution: 1. Begin by turning your ignition key to the OFF position. Locate the black diagnostic (OBDII) connector (Figure #1) under the dash near the steering column. - Page 12 Evolution FORD 4.6 and 5.4 Liter 3. Feed roughly 8 to 10 inches of cable through the dashboard. Mount the Pod onto the dashboard (shown in Figure #4) with the end of the cable protruding through the front of the Pod. With the Pod secure, attach the Evolution to the cable.
- Page 13 Ford 4.6 and 5.4 Liter Evolution 5. After pressing [ENTER], the main display will come up. Note: Parameters and values might vary. 6. There are five boxes that will be displaying information about your vehicle. The black box in the top right corner displays which level is currently programmed onto your vehicle.
-
Page 14: Power Programming
Evolution FORD 4.6 and 5.4 Liter The other four boxes can show up to 4 PIDs (Parameter IDs) of your vehicle. By default, they are your vehicle’s RPM, MPH, TFT (transmission fluid temperature), and ECT (engine coolant temperature). Optional parameters and display formats may be selected in the Set Up/Changing Variables section of this manual. - Page 15 Ford 4.6 and 5.4 Liter Evolution 2. You have the option to change certain parameters of the level you chose. If you would like to learn more about what parameters are available and how to use them, then read the Custom Options section in this manual.
-
Page 16: Custom Options
Note: Custom Options are provided to allow for flexibility based on driver preferences. Any option customization done by the user is not warranted by Edge Products. Please use at your own discretion. The following customizable options are available: Gear Ratio The Evolution has the ability to correct for modified gear ratios. -
Page 17: Tire Size
Ford 4.6 and 5.4 Liter Evolution The default value the Evolution displays is the current value stored in the PCM. Adjust the value displayed by pressing the [UP] and [DOWN] arrow keys. You can change the gear ratio from 2.73 to 5.13 in increments of 0.01. Changing this value will allow your PCM to accurately calculate vehicle speed and odometer readings. -
Page 18: Idle Speed
Evolution FORD 4.6 and 5.4 Liter The numbers on this screen represent the circumference (in mm) of your tire size. The default value the Evolution displays is the current value stored in the PCM. Adjust the tire size by pressing the [UP] and [DOWN] arrow keys. The following table will help you determine your tire circumference by matching your tire size with the common sizes listed. -
Page 19: Wot (Wide Open Throttle) Shifting
CAUTION: Setting this value too high can cause damage to your engine. Adjusting the rev limiter for purposes inconsistent with the product’s intended function violates the product’s intended use and will invalidate the product’s warranty. Edge Products is not responsible for or liable for the consequences of improper product use. -
Page 20: Torque Converter Lock Points
Timing Adjustment This adjustment modifies the “high load” timing. Based on the octane rating of the fuel used, Edge provides a minor range of timing adjustment to prevent engine damage from detonation, most likely to occur under high load conditions. If you are using less than 91 Octane fuel or are concerned about detonation you may use this feature by decreasing timing by increments of 0.5 counts per adjustment to prevent detonation. -
Page 21: Wot Fuel
Ford 4.6 and 5.4 Liter Evolution does not cause Edge tuning to be taken outside the range of certified exhaust emissions. CAUTION: This option should not be used, unless you have experience in tuning trucks for performance. If used in conjunction with fuel modifiers, the customer must carefully consider the risks and understand the potential impact on the engine and its components. -
Page 22: Clearing Codes
Evolution FORD 4.6 and 5.4 Liter After selecting the Retrieve option, any stored DTCs will appear on the screen like the following example: Press [MENU] to exit the DTC list and return to the previous menu. If you have no trouble codes, the following screen will appear: Clearing Codes If you want to clear the DTCs on your vehicle, select the Clear DTCs option. -
Page 23: Tech Support
Tech Support Information found in this section is normally only accessed when instructed by an Edge support person. For example, Version Info displays the current Bootloader, Firmware, and Calibration versions installed on your Evolution. Your vehicle’s HEX code is also shown. Using the Fusion® software, you will be able to access online updates to ensure your Evolution is always up to date. - Page 24 Evolution FORD 4.6 and 5.4 Liter 3. Select the desired performance test (0-60 screen is shown below). If your vehicle is moving at this time, the Evolution will ask you to come to a stop. 4. For the 0-60 MPH run, press the accelerator pedal and the test automatically begins.
-
Page 25: Setup
Ford 4.6 and 5.4 Liter Evolution This will show how long it took you to cover 60 feet, 1/8 mile, and ¼ mile. In addition, your MPH at ¼ mile will also be shown (see the example above). The best run is stored for later viewing. You may also use the back of this manual to write down your times. -
Page 26: Two Function Bar Graph Display Sample
Evolution FORD 4.6 and 5.4 Liter 2. Select the Display option. The following screen appears: 3. Select the desired viewing option by using the [UP] and [DOWN] arrows and pressing the [ENTER] key on the desired display type. Below are examples of the display options: Two Function Bar Graph Display Sample Two Function Digital Display Sample... -
Page 27: Three Function Digital Display Sample
Ford 4.6 and 5.4 Liter Evolution Three Function Digital Display Sample Four Function Digital Display Sample Changing the Variables on the Screen To change the variables on the screen, perform the following steps: 1. From the Main Menu select the Setup option. The Setup screen appears as follows: 2. - Page 28 Evolution FORD 4.6 and 5.4 Liter 3. Select the style which you would like the parameters to be displayed on your screen and press [ENTER]. Depending on which display you select, a screen similar to the following appears: 4. This screen lists the current parameters being displayed and their respective positions on the screen (i.e., TOP LEFT, etc.).
- Page 29 Ford 4.6 and 5.4 Liter Evolution ECT (engine coolant temperature) – Degrees F. EOT (engine oil temperature) – Degrees F. (NOTE: EOT feature will not work on 2007 and newer F150 models) TFT (transmission fluid temperature) – Degrees F. ...
-
Page 30: Changing Display Backlighting
Evolution FORD 4.6 and 5.4 Liter Changing Display Backlighting Adjusting the Backlight Color To change the backlighting color, perform the following steps: 1. From the Main Menu select the Setup option. The Setup screen appears as follows: 2. Select the Display option. The following screen appears: 3. -
Page 31: Adjusting The Backlight Brightness
Ford 4.6 and 5.4 Liter Evolution 5. Depending on the color you select, a screen similar to the following appears (example of Red): 6. As you adjust the percentage shown on the screen, you should notice a change in the color of the screen. Once the desired color value has been reached, press [ENTER]. -
Page 32: Alerts
Evolution FORD 4.6 and 5.4 Liter 2. Select the Display option. The following screen appears: 3. Select the Adjust LCD Settings option. The following screen appears: 4. Select Contrast, and use the up and down arrows to adjust the contrast to where you’d like. - Page 33 Ford 4.6 and 5.4 Liter Evolution 1. From the Main Menu select the Setup option. The Setup screen appears as follows: 2. Select the Alerts option. A screen similar to this will appear: 3. By default, the alerts are off. To turn them on, select the Alerts are Off option and press [ENTER].
-
Page 34: Records
Evolution FORD 4.6 and 5.4 Liter 5. When alerts are On, and multiple alerts are detected, the Evolution will only display one. For example: if you exceed the set point for both MPH and RPM, the first alert the Evolution detects will be the one displayed. -
Page 35: Reset Evo Settings
Note: This will not program the vehicle back to stock power; it will only reset the Evolution display options, alerts and records back to the preset defaults from Edge Products. To reset power level, return to “Power Programming”. 1. Enter into the Main Menu. The Main Menu screen appears as follows: 2. -
Page 36: Fusion® Pc Software
Internet Connection Required to Update Fusion® Software allows the user to update their device to the latest version of firmware and calibration files. It can be downloaded for free from Edge Products web site at www.edgeproducts.com. Note: Be sure to install both the SOFTWARE and the DRIVERS that come included in the download before you connect your device to your PC. - Page 37 Ford 4.6 and 5.4 Liter Evolution and password into the login screen. You’ll be prompted to connect the device to launch the update. After connecting the device, you’ll see the following screen. Click yes to continue with the update. Note: Be sure to return your vehicle to stock before connecting the device to Fusion.
-
Page 38: Possible Programming Errors
During programming, the device will read the stock file on your vehicle and compare it to a corresponding stock file that has been verified by Edge Products. If there is a mismatch the device will alert you, and display this... -
Page 39: Recommended Dyno Procedure
Ford 4.6 and 5.4 Liter Evolution “Non-stock condition detected. This is most likely because your vehicle has been programmed with a competitive product. It is recommended that you return your vehicle to a stock condition with the product that changed it. Alternatively, you can plug your device into the internet update system and it will load the necessary files onto your device to return your vehicle to stock.”... -
Page 40: Troubleshooting/Tips
FORD 4.6 and 5.4 Liter Obtain a scan tool that allows for “Active Command” modes. The Hickok NGS™ is the one Edge Products uses for testing and also the recommended tool. (Note: Diagnostic modes may vary between tool manufacturers and some options may not be available, including “Active Command”... - Page 41 Return to Stock. This will allow the Evolution to reprogram the PCM with the factory calibration and recover the PCM. If, after reprogramming, you still have a “No-Start” condition, contact Edge Products Technical Support. A member of our support team can further instruct you on possible recovery procedures.
-
Page 42: Warranty Information
Warranty Information LIMITED 1 YEAR WARRANTY Edge Products, LLC, (hereafter "SELLER") gives Limited Warranty as to description, quality, merchantability, fitness for any product’s purpose, productiveness, or any other matter of SELLER's product sold herewith. The SELLER shall be in no way responsible for the product’s open use and service and the BUYER hereby waives all rights other than those expressly written herein. - Page 43 Edge is committed to providing quality products that are safe to use. Our products do not cause damage to a vehicle when used as intended. Please keep in mind that towing in anything higher than the towing level and hard driving in race or extreme performance levels is not recommended.
-
Page 44: Commonly Used Acronyms
To expedite your support call, please have your Vehicle Information, Part Number, Serial Number, and Date of Manufacture ready prior to calling Technical Support. The Edge Products information is found on the label located on the bottom of the device.