Hakko Electronics FR-810 Instruction Manual

SMD Rework Station
Instruction Manual
Thank you for purchasing the HAKKO FR-810 SMD Rework Station.
This unit features digital control and display of hot air temperature.
Please read this manual before operating the HAKKO FR-810.
Keep this manual readily accessible for reference.
1. PACKING LIST AND PART NAMES
HAKKO FR-810 station Power cord
1
Handpiece holder Nozzle N51-02 (ø4)
1
Instruction manual
FP pick-up {with FP pick-up wire(SS)}
1
Heat resistant pad
1
handpiece holder
attachment plate
Handpiece holder
HAKKO FR-810
station
Heat resistant pad
Handpiece
Temp/Time indicator Air indicator
2. SPECIFICATIONS
● Station
Power consumption 100V-700W 110V-840W 120V-820W
Power consumption
220V-1100W 230V-1200W 240V-1300W
Capacity (Airflow)
● Handpiece
Control temperature
Power consumption 100V-670W 110V-810W 120V-790W
Outer dimensions
220V-1070W 230V-1170W 240V-1270W
250 mm (9.8 in.)
Total length (w/o cord)
Weight
180 g (0.40 lb.)
Weight (w/o cord)
* Airflow capacity is rated as free flowing. Restrictions
* This product is protected against electrostatic discharge. created by various nozzles may reduce the maximum
airflow capacity.
* Specifications and design are subject to change without
notice.
CAUTION
This product includes such features as electrically
conductive plastic parts and grounding of the
handpiece and station as measures to protect the
device to be soldered from the effects of static
電路板
electricity. Be sure to observe the following
水平支架
instructions:
連接器
1. The handle and other plastic parts are not
插座
insulators, they are conductors. When replacing
parts or repairing, take sufficient care not to
expose live electrical parts or damage
insulation materials.
2. Be sure to ground the unit during use.
3. WARNINGS, CAUTIONS AND NOTES
Warnings, cautions and notes are placed at critical points in this manual to direct the operator's
attention to significant items. They are defined as follows:
WARNING: Failure to comply with a WARNING may result in serious injury or death.
CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved.
NOTE : A NOTE indicates a procedure or point that is important to the process being described.
To avoid damage to the unit, do not turn the power switch OFF until the pump stops automatical by
cooling down after use until
When powered, the temperature of the hot air and the nozzle will become extremely hot, reaching
a maximum temperature of 600℃ (1120℉). Be sure of the following to avoid possible burns / fires :
 Do not direct the hot air toward personnel or touch the metal
parts near the nozzle.
Please check to make sure that all items  Do not allow the nozzle to come close to, or touch, flammable materials.
listed below are included in the package.
 Inform others in the area that the unit is hot and should not be touched.
1
 Turn the power off and allow the unit to cool when changing
1
1 parts or storing the HAKKO FR-810.
 This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
Nozzle
been given supervision or instruction concerning use of the
appliance in safe way and understand the hazards involved.
 Children shall not play with the appliance.
Power cord
 Cleaning and user maintenance shall not be made by
children without supervision.
FP pick-up
To prevent accidents or damage to the HAKKO FR-810, be sure to observe the following:
●
● Turn the power off when not in use, or left unattended.
● The unit is for a counter or workbench use only.
FP pick-up wire(SS)
● Do not strike the handpiece against hard surfaces or otherwise subject it to physical shock.
● Be sure the unit is grounded. Always connect power to a grounded receptacle.
● Do not modify the unit.
● Use only genuine HAKKO replacement parts.
● Do not allow the HAKKO FR-810 to become wet, or use it when hands are wet.
● Remove the power cord by holding the plug - not the cord.
● Be sure the work area is well ventilated.
4. INITIAL SETUP
● Controls and displays
30 W
1 - 9 (5 - 115L/min*)
50 - 600℃ (120 - 1120℉)
160(W) × 145(H) × 220(D) mm
(6.3 × 5.7 × 8.7 in.)
1.5 kg (3.3 lb.)
A. Station assembly
● Attach the handpiece holder.
1. Turn and loosen the knob that locks the handpiece holder.
2. Slide the handpiece holder along the groove on the station in the direction of
the arrow. Turn the knob to lock the handpiece holder in place.
B. Attaching a nozzle
Aligning the groove on the nozzle with the tabs on the
heater pipe and slide the nozzle onto the heater pipe.
Turn the nozzle to lock it in place.
WARNING
appears on the display.
CAUTION
The front panel of HAKKO FR-810 includes five operation buttons.
- Used to start or stop the station.
•Pressing this button when the forced cool down bypass is
enabled will turn the airflow off and stop the cooling process.
- Used for changing values.
•Pressing this button when using Preset Mode will cause the
preset selection screen to appear.
- Used for changing values.
•Hold this button for at least two seconds to enter the Offset
Mode.
- Used for finalizing entered values and checking settings.
•Hold this button for at least two seconds to display the
temp/timer screen.
- Used to set air flow.
•When setting the airflow, you may press
or to
finalize your airflow setting value.
* The handpiece holder can be attached to either side of
the station by removing the handpiece holder attachment
plate and attaching it to the opposite side of the handpiece
holder.
4. INITIAL SETUP
C. Electrical connection and power ON
1. Insert the power cord into the receptacle on the rear panel of the station.
2. Place the handpiece on the holder.
The rim of the handpiece
must rest on the area
circled in the illustration.
CAUTION
When not in use, place the handpiece
on the holder.
3. Plug the other end of the power cord into a grounded
wall socket. CAUTION
This product is protected against electrostatic
4. Turn the power switch ON. discharge. Be sure the unit is grounded.
5. OPERATION
● Air Blow
1. Start
Press the "S" button on the handpiece or (START/STOP) button on the station to start blowing air.
Hot air blows out of the tip of the nozzle. Hot air temperature is controlled according to the temperature
setting.
START/STOP
button
2. Stop
Press the "S" or button again. Power to the heater is shut off and cooling begins. When the
temperature falls to 100°C (200°F), or after 1.5 minutes of cooling, air blow is automatically stopped. The
display will show indicating that the station is ready to start again.
WARNING
Do not stop the hot air by turning the power switch OFF.
If power is turned off after use, there will be no cool-down. To avoid damage to the equipment, do not turn
the power switch OFF until appears on the display.
Setting of the air flow
●
Pressing the AIR button in the station causes the LED for AIR display to blink and allows
you to change air flow. The air flow setting range is 1 to 9.
Actual airflow may be affected by the size and shape of the nozzle(s) used.
Changing the air flow setting from 5 to 7
Example:
Press the Press the
button. button twice.
● Setting/Changing the Temperature and Timer
NOTE:
After accepting the value for the ones digit for temperature, you will have the option to set the timer
starting over with the hundreds digit.
The factory default : "Temperature 300℃ / 540℉" "Timer ｰｰｰ (No setting)"
Example : When the set temperature is 300°C and the timer setting is ---.
1. Setting the Temperature (from 300℃ to 450℃)
Press and hold the
Press the
button for more
button once.
than one second.
Press the or Press the
button 5 times. button.
2. Setting the Timer (from --- to 130sec)
Press the
Press the
button.
button twice.
Press the Press the
button. button. Each of the set values is displayed for
one second, and each change is finalized.
* When you want to leave the timer "ｰｰｰ".
Press the
button once.
Finished
button
"S"
Press the or
button.
Finished
Press the
button.
Press the
Setting the
button.
Timer
Press the
button 3 times.