Table of Contents
Advertisement
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Network Configuration Report as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report.
•
Static IP assignment: Use SetIP program to change the IP address
from your computer. If your machine has a control panel, you can also
change IP address using the machine's control panel.
In an office environment, we recommend that you contact a network
administrator to set this address for you.
IP setting using control panel
1. Connect your machine to the network with an network cable.
2. Turned on the machine.
3. Press Menu on the control panel.
4. Press the up/down arrow to highlight Network and press OK.
5. Press the up/down arrow to highlight TCP/IP and press OK.
6. Press the up/down arrow to highlight Static and press OK.
7. Press the up/down arrow to highlight IP Address and press OK.
8. Enter the IP address using numeric keypad and press OK.
9. Enter other parameters, such as the Subnet Mask and Gateway
and press OK.
10. After entering all parameters, press Stop/Clear to return to ready
mode.
Now go to "Installing wired network connected machine's driver" on
page 40.
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report.
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1. Open Control Panel.
2. Double click Security Center.
3. Click Windows Firewall.
4. Disable the firewall.
Installing the program
1. Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2. Start a web browser such as Internet Explorer and open the X drive.
(X represents your CD-ROM drive.)
3. Double-click Application > SetIP.
4. Double-click Setup.exe to install this program.
5. Click OK. If necessary, select a language from the drop-down list.
6. Follow the instructions in the window and complete the installation.
Starting the program
1. Connect your machine and the computer using network cable.
2. Turned on the machine.
3. From the Windows Start menu, select All Programs > Samsung
Network Printer Utilities > SetIP > SetIP.
4. Click on the
icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine's new information into the configuration window
as follows:
•
MAC Address : Find the machine's MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
MAC address is a hardware serial number of the machine's
network interface and can be found in the Network
Configuration Report.
•
IP Address: Enter a new IP address for your machine.
•
Subnet Mask: Enter a new Subnet Mask for your machine.
•
Default Gateway: Enter ta new Gateway for your machine.
6. Click Apply, and then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7. Click Exit to close the SetIP program.
8. If necessary, restart the computer's firewall.
IP setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1. Open System Preferences.
2. Click Security.
3. Click the Firewall menu.
4. Turn firewall off.
The following instructions may vary for your model.
1. Connect your machine and the computer using network cable.
2. Insert the Installation CD-ROM, and open the disk window. Open the
MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.
3. Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPapplet.html page that shows
the printer's name and IP address information.
4. Highlight the printer information row and select the Setup icon,
which is the second icon from the left in the application menu bar. A
TCP/IP Configuration window will open.
If the printer was not shown in the information row, select the
Manual Setting icon (third from left) to open the TCP/IP
Configuration window.
5. Enter the printer's new information into the configuration window as
follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•
MAC Address: Find the machine's MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
Network setup_ 39
Advertisement
Table of Contents
