Maintenance And Care; Accessories, Tools; Environment; Ec-Declaration Of Conformity - Festool DOMINO DF 500 Q Original Operating Manual

Procedure
Proceed as follows to create a dowelled joint:
- Select a Domino dowel and insert a matching
jointing bit in the Domino dowel jointer (Chap.
7.1).
- Set the jointing depth (Chap. 7.2). The jointing
depth must be at least 3 mm smaller than the
workpiece thickness so that the dowelled joint
is supportable.
- Set the jointing height to correspond to the
workpiece thickness (Chap. 7.3).
- Mark the areas on the workpiece that belong
together [10-1] so that you will be able to join
them correctly again once you have cut the
dowel holes.
- Position the two workpieces to be joined against
one another and mark the desired positions of
the dowels with a pencil [10-2].
- Set the desired dowel-hole width (Chap. 7.5).
Our recommendation: Cut the fi rst hole without
play (dowel-hole width = Domino dowel width),
and the remaining dowel holes to the next larg-
est dowel-hole width (Fig. 10). The fi rst dowel
hole therefore serves as a reference dimension,
whereas the remaining dowel holes have toler-
ance for manufacturing inaccuracies.
- Cut the dowel holes:
a) the fi rst dowel hole by placing the stop latch
at the side edge of the workpiece,
b) the following dowel holes according to the
pencil markings made beforehand and the
scale of the viewing window [10-3].
9

Maintenance and care

Always remove the power supply plug
from the socket before carrying out any
work on the machine.
All maintenance and repair work which
requires the motor casing to be opened
may only be carried out by an authorised
service centre.
Customer service and repair. Only
through manufacturer or service work-
shops: Please fi nd the nearest address
at: www.festool.com/Service
Use only original Festool spare parts!
EKAT
4
Order No. at: www.festool.com/Service
5
3
2
1
The Domino dowel jointer is to a large extent
maintenance-free. However, we recommend an
annual inspection and/or a check after approx.
100 operating hours at an authorised customer
service workshop. This is for the safety of the user
and the value stability of the Domino dowel jointer.
Always keep the machine and the ventilation slots
clean.
Dust deposits must be removed from the guides
[4-3]. Oil the guides regularly and lightly with
resin-free oil (e.g. sewing machine oil).
To secure the clamp lever (see Fig. 6b):
- Remove the clamp lever and tighten the hexagon
screw.
- Attach the clamp lever to the hexagon screw
again.
The tool is fi tted with special motor brushes with
an automatic cut-out. When the brushes become
worn the power supply is shut off automatically
and the tool comes to a standstill.
10

Accessories, tools

For your own safety, use only original
Festool accessories and spare parts.
Festool offers extensive accessories that enable
you to use your machine effectively for a wide
variety of applications, e.g.: routing circle, guide
rails with rows of holes, routing aid, router base
for bench-mounted use.
The accessory and tool order number can be found
in the Festool catalogue or on the Internet under
„www.festool.com".
11

Environment

Do not throw the power tool in your household
waste! Dispose of the machine, accessories and
packaging at an environmentally-responsible
recycling centre! Observe the valid national regu-
lations.
EU only: In accordance with European Directive on
waste electrical and electronic equipment and im-
plementation in national law, used electric power
tools must be collected separately and handed in
for environmentally friendly recycling.
Information on REACh:
www.festool.com/reach
12

EC-Declaration of Conformity

Dowel jointer
DF 500 Q
Year of CE mark: 2006
We declare at our sole responsibility that this
product is in conformity with the following stand-
ards or standardised documents: EN 60745-1, EN
60745-2-19, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3 in accordance with the regula-
Serial no.
498621, 498622
15