Rinse Thermos, Decanter and Serving station ............................Dayly cleaning ........................................Weekly cleaning ........................................ Cleaning Serving station ..............................7 Exterior cleaning ......................................PROGRAMMING ....................................8 A-2, DA-4, Thermos A, Mega Gold A ................................Cater ..........................................Tower ..........................................HVA/HVM ........................................Grinder Original ......................................POSSIBLE SOLUTION ................................19 Original A/M ........................................
Page 3
Grinder original ......................................Grinder EK21 ........................................HVA\HVM ........................................V-2............................................Serving station 2.5L ....................................... Serving station 5L ......................................DIMENSION ..................................... 71 A-2/M-2 ..........................................DA-4/DM-4........................................Thermos A/M ........................................Mega Gold A/M ....................................... Single Tower ........................................Tower ..........................................Single Cater/ Tea Cater ....................................
GENERAL FILTERBREW & SERVING CONCEPT Introduction Thank you for choosing a FILTERBREWER coffee machine. We hope you enjoy it ! Read the user guide before using the machine. Always keep this guide close at hand for future This guide contains important instructions for reference.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Rinse Thermos, Decanter and Serving station Before each brewing, rinse the thermos, decanter or serving station with fresh tap water. When cleaning the outside, use a soft rag with liquid cleaning agent to prevent scratches. CAUTION! The machine should not be submerged in water or washed in a dishwasher.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Dayly cleaning Wash the thermos, decanter(B) and the filter holder with liquid solution for coffee machines. Always remove the filter immediately and clean the filter holder daily, coffee will get moldy. Clean the spray nozzle(A) and the surrounding area. Use a soft rag and liquid solution that does not scratch.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Cleaning Serving station Disassemble the level tube and clean it every week with the enclosed brush. Take off the main lid and clean the mixer tube(A). Cleaning of Serving station Fill the serving station with hot water. ( Full IMPORTANT! brewing without coffee and filter ).
PROGRAMMING FILTERBREW & SERVING CONCEPT A-2, DA-4, Thermos A, Mega Gold A Select machine type Enter the procedure to select machine type is the following: Press all three buttons at the same time before turning on the mains switch The buzzer beeps once.
Page 9
PROGRAMMING FILTERBREW & SERVING CONCEPT A-2, DA-4, Thermos A, Mega Gold A Adjust water amount Adjust amount of brew water Press the buttons at same time in 5 seconds. The buzzer beeps twice. Display shows 0. - Press the button to increase amount of water.
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Normal operation with reduced outlet time This mode is entered by pressing the before turning the mains switch on. The buzzer gives a 5s beep to indicate this mode. This machine operates like in normal mode but the outlet times are reduced by 90% in order to allow faster adjustment of valve times.
Page 11
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Adjusting of water quantity The procedure to enter this mode is the following: ADJUST DISPLAY Press buttons at the same time for 5 seconds until you hear 3 beeps. The display shows the current setting. Adjust with the buttons = (increase) and = (decrease).
Page 12
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Select machine type In this mode the machine type can be chosen. The procedure to enter this mode is the following: Press buttons at the same time before turning the mains switch on until you hear 6 beeps. The display shows the machine type.
Page 13
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Test functions Press buttons at the same time before turning the mains switch on, puts the control board into test mode for time and temperature controlled machines. For the other types pressing buttons before power-on results in test mode.
PROGRAMMING FILTERBREW & SERVING CONCEPT Tower Normal operation with reduced outlet time This mode is entered by pressing before turning the mains switch on. The buzzer gives a 5s beep to indicate this mode. This machine operates like in normal mode but the outlet times are reduced by 90% in order to allow faster adjustment of valve times.
Page 15
PROGRAMMING FILTERBREW & SERVING CONCEPT Tower Adjusting water temperature Press left buttons at the same time for 5 seconds until you hear1 beep. Display shows the present setting(A). Adjust with the left buttons (increase water temp.) and (decrease water temp.) Confirm the new settings by pressing the left button once.
PROGRAMMING FILTERBREW & SERVING CONCEPT HVA/HVM Select machine type Use a decanter to fill up the water tank to the long sensor pin.(A) Keep button (B) pressed while turning on the power switch.(D) The display will show T1, change the type of machine with buttons (B) or (C). T1 = HVA automatic T2 = HVM manual Confirm the choice by holding down the buttons (B) and (C) at the same...
PROGRAMMING FILTERBREW & SERVING CONCEPT Grinder Original Normal operation There are several sub modes for this mode: READY The machine is in this mode after power on. The motor is off and timers are stopped. Pressing the button changes the number of cups to be prepared.
Page 18
PROGRAMMING FILTERBREW & SERVING CONCEPT Grinder Original Adjust coffee amount Press buttons simultaneously for 6 seconds. The display (A) shows the current time setting for grinding. You can now choose to increase or decrease the time 15 = 1.5 seconds for grinding, by pressing the buttons This means that you increase or decrease the amount of coffee grounds.
POSSIBLE SOLUTION FILTERBREW & SERVING CONCEPT Original A/M Fault and solution FAULT POSSIBLE SOLUTION IMPORTANT! - Check plug connection to wall socket. All maintenance - Check fuse in plug. Power switch does not lit and installations - Check if hot plate becomes warm, if so must be done replace power switch.
POSSIBLE SOLUTION FILTERBREW & SERVING CONCEPT Cater, Tower, HVA/HVM Fault and solution LEVEL CONTROL Remove the power SHOWN ON THE POSSIBLE POSSIBLE FAULT cord from the wall DISPLAY SOLUTION socket during any installation work. - The high water level - Clean the level sensor. sensor is triggerd - Replace.
Page 33
ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Chassis Chassis Heating Plate 1 Heating Plate 2 Brown Brown White White ROCKET ROCKET SWITCH SWITCH Black Black Blue Blue Chassis 230V Input Main Power Socket...
Page 41
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DA-4 Spare parts list POS. Part No. Description 120433 Decanter lid 110001 Decanter CQ glass 1204012 Lid of tank original 1204013 Strainer 1102016 Brew basket 1.8L 90 mm 1204015 Water tank complete 1.8L 120422 Air inlet plastic 1.8L 1402150 Screw T20,M4X8...
Page 43
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DM-4 Spare parts list POS. Part No. Description 120433 Decanter lid 110001 Decanter CQ glass 1204012 Lid of tank original 1204013 Strainer 1102016 Brew basket 1.8L 90 mm 1204015 Water tank complete 1.8L 1505041 Silicon hose hot 1.8L 120422 Air inlet plastic 1.8L...
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold A Drawing...
Page 45
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold A Spare parts list POS. Part No. Description 1204012 1204013 Strainer 1204015 Water tank complete 1.8L 1204016 Spray nozzle for water tank 140339 Clip for hose 16.4mm 1505041 Siliocn hose hot W 1.8L 1205101 (230V) Brewing element 230V/2200W 120505 (110V)
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold M Drawing...
Page 47
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold M Spare parts list POS. Part No. Description 1204012 1204013 Strainer 1204015 Water tank complete 1.8L 1505062 Overflow hose 1.8L 160212-03 Over heating protection 1205101 (230V) Brewing element 230V/2200W 120505 (110V) Brewing element 110V/1600W 1031503 Silicon hose cold complete 1102016...
Page 49
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos Office Spare parts list POS. Part No. Description 1102016 Brew basket 1.8L 90 mm 1204012 Lid of tank original 1204013 Strainer original 1204015 Water tank complete 1.8L 160821 (230V) Micro switch tank 1.8L 1608221 (110V) Micro switch 125V 1204014...
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos A Drawing Tank Float Strainer Cover Microswitch holder...
Page 51
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos A Spare parts list POS. Part No. Description 1204012 Lid of tank original 1204013 Strainer original 1102016 Brew basket 1.8L 90 mm 1206604 Gasket DIA18mm x 9mm D2mm 1206603 Gasket DIA23.5mm x 15mm D3mm 2760094 Gasket set for inlet hose 1505042...
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos M Drawing Tank Float Strainer Cover Microswitch holder...
Page 53
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos M Spare parts list POS. Part No. Description 1204012 Lid of tank original 1204013 Strainer original 1102016 Brew basket 1.8L 90 mm 1204015 Water tank complete 1.8L 160821 (230V) Micro switch tank 1.8L 1608221 (110V) Micro switch 125V 1204014...
Page 65
EXPLODED VIEW FILTERBREW & SERVING CONCEPT HVA\HVM Spare parts list POS. Part No. Description 1304061 Lid plastic HVA 1031301 HVA lid 1304062 Top plastic HVA 160970 CQ sticker 1802120 Connection faucet short 120200-02 Faucet metal black top 1031641 Electronic unit PCB HVA 1603853 Membrane switch HVA 253207...
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 2.5L Drawing...
Page 68
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 2.5L Spare parts list POS. Part No. Description 1103351 Lid Cover with Tie 1103452 Brew-Thru Lid with SS Tube (2.5L) 1103453 Main housing with Upp 2.5L 1103455 Lower Housing 2.5L 1103456 Outlet Tube Jacket (2.5L) 1103457 Stand 2.5L 1103364...
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 5L Drawing...
Page 70
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 5L Spare parts list POS. Part No. Description 1103351 Lid Cover with Tie 1103352 Brew-Thru Lid with SS Tube (5L) 1103353 Main Housing with Upper Housing 1103355 Lower Housing 5L 1103356 Outlet Tube Jacket (5L) 1103357 Stand 1103364...
DIMENSION FILTERBREW & SERVING CONCEPT Grinder Original Model Grinder Original 570mm 215mm 368mm 390mm...
Page 84
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precaution has been made and warranty claim been issued without delay. The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen.
Need help?
Do you have a question about the A-2 and is the answer not in the manual?
Questions and answers