Contents 1 Preliminary note ���������������������������������������������������������������������������������������������������3 1�1 Symbols used ������������������������������������������������������������������������������������������������3 2 Safety instructions �����������������������������������������������������������������������������������������������4 3 Function and features ������������������������������������������������������������������������������������������5 4 Function ���������������������������������������������������������������������������������������������������������������5 4�1 Evaluation ������������������������������������������������������������������������������������������������������5 4�2 Switching function ������������������������������������������������������������������������������������������6 4�3 Analogue function �����������������������������������������������������������������������������������������6 5 Installation������������������������������������������������������������������������������������������������������������8 6 Electrical connection ��������������������������������������������������������������������������������������������8 7 Operating and display elements ��������������������������������������������������������������������������9 8 Menu ������������������������������������������������������������������������������������������������������������������10 8�1 Menu structure ���������������������������������������������������������������������������������������������10 8�2 Explanation of the menu ������������������������������������������������������������������������������...
10�2 Fault indication ������������������������������������������������������������������������������������������17 11 Technical data and scale drawing ��������������������������������������������������������������������17 11�1 Setting ranges ��������������������������������������������������������������������������������������������17 12 Factory setting �������������������������������������������������������������������������������������������������18 1 Preliminary note 1.1 Symbols used ► Instruction > Reaction, result […] Designation of buttons, switches or indications → Cross-reference Important note Non-compliance can result in malfunctions or interference�...
2 Safety instructions • Read this document before installing the unit� Ensure that the product is suita- ble for your application without any restrictions� • Non-adherence to the operating instructions or technical data can lead to personal injury and/or damage to property� • Improper or non-intended use may lead to malfunctions of the unit or to unwan- ted effects in your application�...
Type of pressure: relative pressure Pressure resistance Order no. Measuring range (max. permissible Bursting pressure pressure)* PY2954 -1���10 -14�5���145 1088 2 175 * in case of static overpressure MPa = bar ÷ 10 / kPa = bar × 100 Static and dynamic overpressures exceeding the indicated overload pres- sure are to be avoided by taking appropriate measures�...
4.2 Switching function OUTx changes its switching state if it is above or below the set switching limits (SPx, rPx)� The following switching functions can be selected: • Hysteresis function / normally open: [OUx] = [Hno] (→ fig. 1). • Hysteresis function / normally closed: [OUx] = [Hnc] (→ fig. 1). First the set point (SPx) is set, then the reset point (rPx) at the requested distance� • Window function / normally open: [OUx] = [Fno] (→ fig. 2).
Page 7
Voltage output 0 ... 10 V Factory setting Measuring range scaled U [V] U [V] P = system pressure, MEW = final value of the measuring range In the set measuring range the output signal is between 0 and 10 V� It is also indicated: System pressure above the measuring range: output signal >...
5 Installation Before mounting and removing the sensor, make sure that no pressure is applied to the system� ► Insert the unit in a G¾ process connection� ► Tighten firmly� 6 Electrical connection The unit must be connected by a qualified electrician� The national and international regulations for the installation of electrical equipment must be adhered to�...
7 Operating and display elements 1 2 3 4 5 6 7 8 Mode/Enter Set 1 to 8: Indicator LEDs - LED 1 to LED 6 = system pressure in unit of measurement as indicated on the label� - LEDs 4 to 6 not used for units with 3 adjustable units of measurement� - LEDs 5 and 6 not used for units with 4 adjustable units of measurement�...
8.2 Explanation of the menu SP1/rP1 Maximum / minimum value for system pressure, at which output 1 changes its switching status� SP2/rP2 Maximum / minimum value for system pressure, at which output 2 changes its switching status� Output function for OUT1: • Switching signal for the limit values: hysteresis function [H ��] or window function [F ��], normally open [�...
9 Parameter setting During the parameter setting process the unit remains in the operating mode� It continues its monitoring function with the existing parameters until parameter setting has been terminated� 9.1 Parameter setting general Each parameter setting requires 3 steps: Parameter selection ►...
Page 13
► Press [Set] and keep it pressed until Mode/Enter Set the valid code no� is displayed� ► Press [Mode/Enter] briefly� On delivery by ifm electronic: no access restriction� ► Press [Set] briefly� > The first parameter of the sub-menu Mode/Enter Set is displayed (here: [HI])�...
9.2 Setting the output signal 9.2.1 Setting the output function ► Select [OU1] and set the switching function: [Hno] = hysteresis function / normally open, [Hnc] = hysteresis function / normally closed, [Fno] = window function / normally open, [Fnc] = window function / normally closed� ►...
9.3 User settings (optional) 9.3.1 Setting the unit of measurement for the system pressure ► Select [Uni] and set the unit of measurement: [bAr], [mbAr] [MPA], [kPA] [PSI] [IH2O] (only PN2009, PN2027, PN2028, PN2069) [inHG] (only PN2009) [mmWS] (only PN2028) 9.3.2 Configuring the display ►...
9.3.5 Setting the output polarity ► Select [P-n], set [PnP] or [nPn]� 9.3.6 Setting the damping for the switching outputs ► Select [dAP], set value between 0�01 ��� 4�00 s; (at 0�00 [dAP] time is not active)� dAP-value = response time between pressure change and change of the switching status in seconds (s)�...
10 Operation After power on of the supply voltage the unit is in the Run mode (= normal operati- on)� It carries out its measurement and evaluation functions and generates output signals according to the set parameters� Operating indicators → 7 Operating and display elements. 10.1 Read the set parameter values ►...
Page 18
12 Factory setting Factory setting User setting 25 % VMR* 23 % VMR* 75 % VMR* 73 % VMR* -1 bar 100 % VMR* 0.06 0.10 bAr / mbAr * the indicated percentage of the final value of the measuring range of the corresponding sensor in bar / mbar is set�...