Advertisement
Quick Links
Quick Start Guide
SZ09-EN-001
1. To ensure the printing quality, please don't open the light shield unless it's necessary.
Caution
2. Unused photopolymer resin needs to be stored in a dark, dry, and cool place.
3. Please clean the finished model with isopropyl alcohol (IPA).
Warning
Please put on gloves while using photopolymer resin to avoid direct contact with hands.
User Guide
The instruction(user guide) is stored in an attached USB disk.
This guide only applies to Flashforge Hunter DLP 3D printer
Advertisement
Related Manuals for Flashforge Hunter
Summary of Contents for Flashforge Hunter
- Page 1 3. Please clean the finished model with isopropyl alcohol (IPA). Warning Please put on gloves while using photopolymer resin to avoid direct contact with hands. User Guide The instruction(user guide) is stored in an attached USB disk. This guide only applies to Flashforge Hunter DLP 3D printer...
- Page 3 Getting to Know Your HUNTER The Back of the Printer Light Shield Z-Axis Power Switch Power Input Port Platform Screw Built Plate Vat Film Screw Resin Vat Touch Screen Stand-by Switch U Disk Input USB Input...
-
Page 7: Pour Photopolymer Resin Into Vat
Pour Photopolymer Resin into Vat 1. Tear off the seal, then open the cap. 2. There is a rubber plug at the mouth of the bottle. Lift the ring open and take out the rubber plug. M A X Caution Pour photopolymer resin slowly to prevent liquids from spilling out. -
Page 8: First Print
1. Connect power cable and power cord adapter. 2. Plug the power cable into the outlet on the 3. Insert the attached USB stick into Hunter. back of Hunter and turn on the power button. 3. Click [Print]-[ USB Memory ]- [20mm_box], then click start icon to start printing. - Page 11 Caution Please pay attention to the direction during installation as shown in the left. 4. Adjust the direction when needed, put the build platform back in place then tighten the bolt.
- Page 12 How to Remove the Resin Vat 1. Unscrew the two screw on both sides. 2. Take out the resin vat. Caution Please pay attention to the direction during installation. Refer to figure 2. If there is photopolymer resin left in resin vat, please put it back to the printer and cover it with light shield as soon as possible to avoid the liquid being solidified by exposing to light.
- Page 13 How to Change the Vat Film Flat Washer Please don't lose two washers while remove the bolt. Spring Washer 1. Place resin vat flat on workbench, unscrew all bolts with hexagon 2. Turn the resin vat over, unscrew four bolts from the bottom of the wrench.
- Page 14 Clean Parts Keep screw holes aligned Resin Vat Bottom Plate Silicone Middle Plate Washer Transparent Glass Silicone Washer Wall Wall 5. Carefully clean the resin vat bottom plate, middle plate, wall, 6. After washing, place the resin vat on a workbench, then install the transparent glass and silicone washer.
- Page 15 Keep screw holes aligned 9. Tear off the cover on the other side. 10. Put the film onto the resin vat. 11. Turn over the assembled parts. 12. Follow the right sequence to install the screws at four corners according to the illustration.
- Page 16 Handle with care, to avoid damaging vat film 13. Install all the rest screws in the sequence as shown. 14. Put the transparent glass on the vat film Handle with care to avoid breaking the transparent glass. 15. Put the bottom plate back into place. 16.
-
Page 17: Basic Maintenance
10 Basic Maintenance Don't pour the used photopolymer resin back to the original bottle! Keep the two glass plates( as illustrated) clean and without fingerprint. Store the remaining photopolymer resin in a clean sealed container, and keep away from light. Please keep the resin free of any solidified print residue.