Table of Contents
Advertisement
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Block
Detailed
Function
Code
C
0
4
0
C
0
6
0
C
2
1
0
C
2
2
0
C
3
1
1
C
3
1
1
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
2
C
3
1
3
C
3
1
4
C
3
1
4
C
3
1
7
C
3
1
9
C
3
1
9
C
3
1
9
C
3
2
1
C
3
2
1
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
2
C
3
2
3
C
3
2
4
C
3
2
4
C
3
2
6
HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U
Symptom/State
0
Non-standard battery is used.
0
The battery is too hot.
0
Condensation.
0
Video head is dirty.
LOAD direction. Loading does not
0
complete within specified time
UNLOAD direction. Loading does not
1
complete within specified time
0
T reel side tape slacking when unloading.
1
S reel side tape slacking when unloading.
2
T reel fault.
3
S reel fault.
4
T reel and S reel FG short fault.
0
FG fault when starting capstan.
0
FG fault when starting drum.
2
FG fault during normal drum operations.
Retry fault when catching one's finger
2
in cassette compartment.
Vector fault (Judgement with the set
7
state that is impossible actually for fault
of sensors.)
Vector fault (Judgement with the set
8
state that is impossible actually for fault
of sensors.)
Vector fault (Judgement with the set
9
state that is impossible actually for fault
of sensors.)
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
S reel side tape slacking when
1
unloading.
2
T reel fault.
3
S reel fault.
4
T reel and S reel FG short fault.
0
FG fault when starting capstan.
0
FG fault when starting drum.
FG fault during normal drum
2
operations.
Difficult to adjust focus
0
(Cannot initialize focus.)
Use the InfoLITHIUM battery.
Replace the battery or remove it and put it in cool place.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
If it does not recover, inspect the focus MR sensor of lens drive
block (Pin q;, qs of CN5002 on the VC-543 board).
If not faulty, inspect the focus motor drive circuit
(IC6001 on the VC-543 board).
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
Correction
Hide quick links:
Advertisement
Table of Contents
