Siemens SINUMERIK 808D Programming And Operating Manual page 147
Iso turning/milling
Hide thumbs
Also See for SINUMERIK 808D:
- Diagnostic manual (566 pages) ,
- Parameter manual (524 pages) ,
- Commissioning manual (508 pages)
Table of Contents
Advertisement
Sample program
;
N001 G49
N002 G10 L10 P11 R200.
N003 G10 L10 P15 R190.
N004 G10 L10 P30 R150.
N005 G92 X0 Y0 Z0
N006 G90 G00 Z250.0 T11 M6
N007 G43 Z0 H11
N008 S30 M3
N009 g99 G81 X400.0 Y-350.0 Z-153.0 R-
97.0 F1200
N010 Y-550.0
N011 G98 Y-750.0
N012 G99 X1200.0
N013 Y-550.0
N014 G98 Y-350.0
N015 G00 X0 Y0 M5
N016 G49 Z250.0 T15 M6
N017 G43 Z0 H15
N018 S20 M3
N019 G99 G82 X550.0 Y-450.0 Z-130.0 R-
97.0 P300 F700
N020 G98 Y-650.0
N021 G99 X1050.0
N022 G98 Y-450.0
N023 G00 X0 Y0 M5
N024 G49 Z250.0 T30 M6
N025 G43 Z0 H30
N026 S10 M3
N027 G85 G99 X800.0 Y-350.0 Z-153.0
R47.0 F500
N028 G91 Y-200.0 K2
G80
N029 G28 X0 Y0 M5
N030 G49 Z0
N031 M30
Programming and Operating Manual (ISO Turning/Milling)
01/2017
; Deselect the tool length compensation
; Setting the tool offset 11 to +200.
; Setting the tool offset 15 to +190.
; Setting the tool offset 30 to +150.
;
Setting the coordinates at the reference position
;
; Tool change
; Initial plane, tool length compensation
; Spindle start
; Positioning, then drill #1
;
Positioning, then drilling #2 and return to plane
;
point R
;
Positioning, then drilling #3 and return to ini-
;
tial plane
;
Positioning, then drilling #4 and return to plane
;
point R
;
Positioning, then drilling #5 and return to plane
;
point R
;
Positioning, then drilling #6 and return to ini-
;
tial plane
;
Return to reference position,
;
Spindle stop
;
Deselection of tool length compensation, tool
;
change
; Initial plane, tool length compensation
; Spindle start
;
Positioning, then drilling #7 and return to plane
;
point R
;
Positioning, then drilling #8 and return to ini-
;
tial plane
;
Positioning, then drilling #9 and return to plane
;
point R
;
Positioning, then drilling #10 and return to ini-
;
tial plane
;
Return to reference position,
;
Spindle stop
;
Deselection of tool length compensation, tool
;
change
; Initial plane, tool length compensation
; Spindle start
;
Positioning, then drilling #11 and return to plane
;
point R
;
Positioning, then drilling #12 and 13, and return
;
to plane point R
; Deselection of the fixed cycle
;
Return to reference position,
;
Spindle stop
; Deselect the tool length compensation
; End of the program
147
Advertisement
Table of Contents
