Hilti ST 1800-A22 Operating Instructions Manual
Hide thumbs
Also See for ST 1800-A22:
- Original operating instructions (298 pages) ,
- Manual (72 pages) ,
- Operating instructions manual (19 pages)
Related Manuals for Hilti ST 1800-A22
Summary of Contents for Hilti ST 1800-A22
- Page 1 ST 1800A22 English Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 2 Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 3 Revolutions per minute 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
- Page 4 ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Cordless metal screwdriver ST 1800A22 Generation Serial no.
- Page 5 ▶ Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control. Using and handling the cordless power tool ▶ Use only the specified batteries in the power tools. Use of any other batteries may present a risk of injury and fire.
- Page 6 Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 7 Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 8 3 Description 3.1 Overview of the product Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 9 It is possible to use a stand-up tool for driving collated screws. ▶ Use only Hilti Liion batteries from the B 18 / B 22 series with this product. ▶ Use only Hilti battery chargers of the C4/36 series with these batteries.
-
Page 10: Operation
5 Operation 5.1 Inserting the battery WARNING Risk of injury! Inadvertent starting of the impact screwdriver. ▶ Before fitting the battery, check that the cordless impact screwdriver is switched off and that the forward/reverse switch is in the middle position (i.e. safety lock engaged). WARNING Electrical hazards! Risk of short circuiting. - Page 11 ▶ Fit the depth gauge. 5.3 Setting the depth gage (accessory) ▶ Adjust the depth gauge. 5.4 Using the protective cap Note When the depth gauge is not fitted, the guard protects the depth gauge holder from dirt and damage. ▶...
- Page 12 ▶ Fit the accessory tool or, respectively, remove it. 5.6 Fitting / removing the screw guide (optional) Note Use of the Hilti ST-SG 5.5/6.5 screw guide is recommended for sandwich panel screws. ▶ Fit / remove the screw guide. 5.7 Setting forward or reverse rotation Note An interlock prevents switching while the motor is running.
- Page 13 ▶ Set the forward/reverse switch to the desired direction of rotation. 5.8 Setting the torque ▶ Set the desired torque. 5.9 Safe operation WARNING Electric shock A fastener coming into contact with a concealed electric cable may result in electric shock.
- Page 14 ▶ Always hold the tool by the grip and/or with the hands on plastic parts of the casing. 5.10 Switching on Note The metal construction screwdriver must be pressed lightly against the working surface as it will otherwise not start (for safety reasons). The running speed can be controlled smoothly right up to maximum speed by varying how far the control switch is pressed in.
- Page 15 ▶ Switch off after sustained operation. 5.13 Removing screws Note Remove the depth gauge or screw guide, if fitted. Set the forward / reverse switch to the “Reverse” position. ▶ Remove the screws. 5.14 Removing the battery ▶ Remove the battery. 6 Care and maintenance of cordless tools WARNING Danger of electric shock! Carrying out care and maintenance while the battery is fitted presents a...
-
Page 16: Troubleshooting
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com... - Page 17 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
- Page 18 10 Manufacturer’s warranty ▶ Please contact your local Hilti representative if you have questions about the warranty conditions. Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 19 Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...
- Page 20 Hilti = registered trademark of Hilti Corp., Schaan 20160714 Printed: 27.07.2016 | Doc-Nr: PUB / 5293030 / 000 / 00...