Page 1
ST 1800-A22 Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Οδηγιες χρησεως Használati utasítás Instrukcja obsługi Инструкция по зксплуатации Návod k obsluze Návod na obsluhu Upute za uporabu Navodila za uporabo Ръководство...
ORIGINAL OPERATING INSTRUCTIONS ST 1800‑A22 cordless screwdriver for metal 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages.
Observe the information printed in the operating instructions concerning operation, care and maintenance. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Do not use the battery as a power source for other unspecified appliances.
Page 8
2.4 Lubrication Grease lubrication 2.5 Grip Vibration-absorbing ergonomic grip (in-line grip) 2.6 Power tool overloading and overheating indicator The power tool is equipped with an electronic protection system to prevent overloading and overheating. The power tool switches itself off automatically in the event of overloading and overheating. After releasing the control switch, the power tool may not restart immediately when the switch is pressed again (while the power tool is cooling down).
3 Accessories Designation Description Short designation Depth gauge ST‑DG 19 for screws with sealing washers up to 19 mm diameter Depth gauge ST‑DG 22 for screws with sealing washers up to 22 mm diameter Guard ST‑DC Screwdriving accessories S‑NSD sockets for driving hex. screws (7, 8, 10, 12, ¼", ⁵⁄₁₆", ³⁄₈") Stand-up tool SDT 25/15...
Noise and vibration information (measured in accordance with EN 60745‑2‑2): Typical A-weighted sound power level 81 dB (A) Typical A-weighted emission sound pressure level 70 dB (A) Uncertainty for the given sound level 3 dB (A) Triaxial vibration values (vibration vector sum) Screwdriving without impact action, a 0.5 m/s²...
Page 11
c) When battery pack is not in use, keep it away switch or energising power tools that have the switch on invites accidents. from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, d) Remove any adjusting key or wrench before turn- that can make a connection from one terminal to ing the power tool on.
Observe the special instructions applicable to the of the type recommended by Hilti for wood dust transport, storage and use of Li-ion batteries. and/or mineral dust together with this tool. Ensure e) Avoid short-circuiting the battery.
(forward/reverse switch in the middle position). Use (transport position). only the Hilti batteries approved for use with this If you disconnect a battery pack from the power tool power tool. for transport or storage, make sure that the contacts of the battery pack are not short-circuited.
Page 14
The speed of the power tool can be controlled Compression of the screw seal is increased. smoothly (increased from zero to maximum) by pressing the control switch gradually. 7.8.3 Removing the depth gauge 7 6 To switch the tool off, release the control switch. Pull the depth gauge forward, away from the power tool.
8.1 Care of insert tools Charge the battery with the Hilti charger approved for use with Li-ion batteries. Clean off dirt and dust deposits adhering to the insert NOTE...
The retaining lugs on the battery are Clean the retaining lugs and check an audible double click. dirty. that the battery engages securely. Contact Hilti Service if the problem persists. The power tool or the battery Electrical fault. Switch the power tool off immedi- gets very warm.
Dispose of the batteries in accordance with national regulations or return them to Hilti. Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling.
12 EC declaration of conformity (original) Hilti Corporation, Feldkircherstrasse 100, Designation: Cordless screwdriver for FL‑9494 Schaan metal Type: ST 1800‑A22 Generation: Year of design: 2010 We declare, on our sole responsibility, that this product Markus Messmer Tassilo Deinzer complies with the following directives and standards: Head of Quality, Processes &...