Ports – Ethernet Menu
Command
ETH.DEFAULTGATEWAY
ETH.DHCP
ETH.DNSPRIMARY
ETH.DNSSECONDARY
ETH.ECHO
ETH.IPADDRESS
ETH.LOCALHOSTNAME
ETH.MACADDRESS
ETH.NETMASK
ETH.PORT
ETH.REMOTESERVERIP
ETH.REMOTESERVERPORT
Ports – USBCOM Menu
Command
EDP.ECHO#2
ECHO
EDP.EOLDLY#2
EOLDLY
EDP.PRNMSG#2
PRNMSG
EDP.REMPNT#2
REMPNT
EDP.RESPONSE#2
RESPNS
EDP.SFMT#2
SFMT
EDP.TERMIN#2
TERMIN
EDP.TRIGGER#2
TRIGGE
Stream Tokens Menu
Command
STR.GROSS
String transmitted for the <M> token for gross weight.
STR.INVALID
String transmitted for the <S> token when weight is invalid.
STR.MOTION
String transmitted for the <S> token when scale is in motion.
STR.NEG
Character transmitted for the <P> token when the weight is
negative.
STR.NET
String transmitted for the <M> token for net weight.
STR.OK
String transmitted for the <S> token when the scale is ok.
STR.POS
Character transmitted for the <P> token when the weight is
positive.
STR.PRI
String transmitted for the <U> token for primary units.
STR.RANGE
String transmitted for the <S> token when the scale is out of
range.
STR.SEC
String transmitted for the <U> token for secondary units.
STR.TARE
String transmitted for the <M> token for tare weight.
STR.ZERO
String transmitted for the <S> token when the scale is at
center of zero.
62
880 Installation Manual
Menu
DFTGWY
Default gateway
DHCP
Dynamic Host Configuration Protocal
DNSPRI
Primary DNS server address
DNSSEC
Secondary DNS server address
ECHO
Specifies whether characters received by the
port are echoed back to the sending unit
IPADRS
IP address for the device
LHSTNM
Local host name
MAC
MAC address
NETMSK
Subnet mask address
PORT
Port used for communication
RMOTIP
Remote IP address
RMOTPT
Remote port number
Table 6-7. PORTS – Ethernet EDP Commands
Menu
Specifies whether characters received by the port are
echoed back to the sending unit
Port end-of-line delay
Displays print message
Remote Print
Specifies whether the port transmits replies to serial
commands
Stream format
Termination character
Selects the operation of the port.
Table 6-8. PORTS – USBCOM EDP Commands
Description
Table 6-9. Stream Tokens EDP Commands
Description
Description
Default
G
I
M
-
N
" "
SPACE
L
O
K
T
Z
Choices / Range
Valid IP address
OFF, ON
Valid IP address
Valid IP address
OFF, ON
valid IP address
Alphanumeric, max Length: 16
n/a – read only
Valid IP address
Range: 1 - 65535
Valid IP address
Range: 1 - 65535
Choices / Range
OFF, ON
Range: 0 - 255
OFF, ON
BOTH, LOCAL, REMOTE
OFF, ON
Alphanumeric, max Length: 200
CR/LF, CR
COMAND, STRLFT, STRIND
Choices / Range
Alphanumeric, Max Length: 8
Alphanumeric, Max Length: 2
Alphanumeric, Max Length: 2
NONE, SPACE, -
Alphanumeric, Max Length: 8
Alphanumeric, Max Length: 2
NONE, SPACE, +
Alphanumeric, Max Length: 8
Alphanumeric, Max Length: 2
Alphanumeric, Max Length: 8
Alphanumeric, Max Length: 8
Alphanumeric, Max Length: 2
Need help?
Do you have a question about the 880 and is the answer not in the manual?