Hilti DX860-ENP Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Tools
  5. DX 860-ENP
  6. Operating instructions manual

Hilti DX860-ENP Operating Instructions Manual

Powder-actuated fastening tool
Hide thumbs Also See for DX860-ENP:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions
Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01
Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00
DX 860-ENP
Operating instructions
Mode d'emploi
Manual de instrucciones
en
fr
es

Advertisement

Table of Contents
loading

Related Manuals for Hilti DX860-ENP

Summary of Contents for Hilti DX860-ENP

  • Page 1 DX 860-ENP Operating instructions Mode d’emploi Manual de instrucciones Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...
  • Page 2 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...
  • Page 3 max. min. max. min. Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...
  • Page 4 X-ENP Standard High-strength steel steel S 235, S275 S 355, S275 E 36, ST 37, E 42, ST 52, 340-470 N/mm 490-630 N/mm Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...
  • Page 5 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...

  • Page 6: Table Of Contents

    Make a note of this informa- 5. Safety precautions tion in your operating instructions and always refer to 6. Before use it when making an enquiry to your Hilti representative 7. Operation or service department. 8. Care and maintenance 9.

  • Page 7: Description

    I-VO 805 PS Protective glasses, clear I-VO 808 PS Protective glasses, tinted Ear protectors Small Hilti lubricant spray Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...

  • Page 8: Technical Data

    Untidiness at the workplace can lead to accidents. To avoid the risk of injury, use only genuine Hilti fas- ● Keep the grips of the tool clean, dry and free form oil ●...

  • Page 9: Before Use

    If nec- cartridge strip is present in the tool, push it forward essary, have the tool repaired at a Hilti service centre. in the direction of cartridge transport until it can be Check the piston stopper and piston for wear and ●...

  • Page 10: Operation

    (5E) These instructions must be observed at all times. Adjust the power regulation wheel to the next lower For detailed information, please ask your local Hilti rep- setting. resentative for a copy of the applicable technical guide- 3.
  • Page 11 3. Carry out the steps described at 8.2.1 or 8.2.2. 7.3 Unloading the tool 4. Turn the rotating sleeve subsequently back through 90° to its original position. 7.3.1 Removing cartridges from the tool -WARNING- Do not attempt to forcibly remove cartridges from the cartridge strip or from the tool.

  • Page 12: Care And Maintenance

    If necessary, per with or modify the piston in any way. have the tool repaired at a Hilti service centre. 7. Pull out the catch before inserting the piston. Hold Use the tool only with the recommended cartridges and the catch in this position until the piston is fully power settings.
  • Page 13 1. Stand the tool on its grip (upside down). -NOTE- 2. Press the red button above the magazine and allow Use of lubricants other than Hilti lubricant spray may the fastener strips to slide out of the magazine. cause damage to rubber parts of the tool, especially the -CAUTION- piston stopper.

  • Page 14: Troubleshooting

    If still not possible, contact Hilti. -NOTE- Do not attempt to forcibly remove cartridges from the strip or from the tool.
  • Page 15 Clean the tool. (8.2.1 and 8.2.2) If these measures fail to remedy the problem, please contact Hilti. Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 01...

  • Page 16: Disposal

    Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. National and international directives and regulations must be observed.

  • Page 17: Health And Safety Of The Operator

    ± 2 dB (C) Further information about user health and safety can be 12.2 Vibration found at www.hilti.com/hse. Total vibration in accordance with 2006/42/EC does not exceed 2.5 m/s². Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00...
  • Page 18 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2973 | 1112 | 00-Pos. 2 | 1 Printed in Liechtenstein © 2012 Right of technical and programme changes reserved S. E. & O 202946 / A2 Printed: 10.04.2017 | Doc-Nr: PUB / 5126862 / 000 / 00...

Table of Contents