Subscribe to Our Youtube Channel
Related Manuals for Hilti DX 860-HSN
Summary of Contents for Hilti DX 860-HSN
- Page 1 DX 860-HSN Operating instructions Mode d’emploi Manual de instrucciones Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
- Page 2 Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
- Page 4 h = 5-9.5mm (3/16"-3/8") h < 5mm (3/16") h > 9.5mm (3/8") Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
- Page 5 Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
-
Page 6: Table Of Contents
1. General information In these operating instructions, the designation " the 2. Description tool " always refers to the DX 860-HSN. 3. Consumables and accessories Location of identification data on the tool 4. Technical data The type designation and serial number are printed on 5. -
Page 7: Description
305957 6.8/11 M40, black For high-strength steel on thick (=.27 CAL short, purple) substructures Wearing parts Item no. Ordering designation Explanation DX 860-HSN spare parts pack Piston and piston brake 284990 Accessories Item no. Ordering designation Explanation 285345 Cleaning Kit Scraper, Round brush 9, Flat brush 3/T69, Round brush 10 (conical), Round brush 22 / 28.5,... -
Page 8: Safety Precautions
Before driving fasteners, check that no one is present ● ● beneath the sheet metal being fastened. missible. To avoid the risk of injury, use only original Hilti fas- ● teners, cartridges, accessories and spare parts or 5.4 General safety precautions those of equivalent quality. -
Page 9: Before Use
6. Before use or when the controls do not operate properly. If nec- essary, have the tool repaired at a Hilti service centre. Check the piston brake and piston for wear and to ● ensure that the parts have been fitted correctly (see 6.1 Check the tool... -
Page 10: Operation
2. Press the last fastener strip in as far as it will go and until flush with the end of the magazine. -WARNING- 7.1.3 Loading a strip of Hilti 6.8/11M40 (=.27 CAL Short) cartridges Driving the fastener may cause ●... -
Page 11: Care And Maintenance
7.2 Remedying faults 7.3 After finishing work with the tool 7.2.1 If the tool misfires or a cartridge fails to fire, 7.3.1 Unloading the tool proceed as follows: -WARNING- Do not attempt to forcibly remove cartridges from the 1. Keep the tool pressed against the work surface for 30 cartridge strip or from the tool. - Page 12 -CAUTION- power regulation pin with accessory round brush. Parts of the tool may become very hot after a period of 9. Lubricate the slider and the collar with Hilti lubricant use. Protective gloves must be worn if the following spray.
-
Page 13: Troubleshooting
Possible cause Remedy Cartridge is not trans- Damaged cartridge strip. Change the cartridge strip ported. Tool is damaged. Contact Hilti. Cartridge strip cannot be Tool is damaged. Contact Hilti. removed from the tool. Tool doesn’t fire. Misfire. See 7.2.1 "Remedying faults”. -
Page 14: Disposal
If these measures fail to remedy the problem, please contact Hilti. 10. Disposal Most of the materials from which Hilti power actuated tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old powder-actuated tools for recycling. -
Page 15: Confirmation Of Cip Testing
12. Confirmation of CIP testing The Hilti DX 860-HSN has been system and type tested. Unacceptable defects or deficiencies, etc. determined As a result, the tool bears the rectangular PTB approval during use of the tool must be reported to the person mark showing approval number S 815. - Page 16 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2972 | 0912 | 0,5-Pos. 4 | 1 Printed in Liechtenstein © 2012 Right of technical and programme changes reserved S. E. & O 282486 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5126874 / 000 / 00...
Need help?
Do you have a question about the DX 860-HSN and is the answer not in the manual?
Questions and answers