York DHP30NWB21SDCP30NWB21SDHP36NWB21SDCP36NWB21S Service Manual page 26

7. SLEEP button
Under COOL, HEAT or DRY mode, press this button to start up sleep function. "
again to cancel sleep function and "
8. TEMP button
By pressing this button, you can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor
unit's display. The setting on remote controller is selected sequentially as below:
● When selecting " " or no display, with remote controller, temperature indicator on indoor unit displays set temperature.
● When selecting " " with remote controller, temperature indicator on indoor unit displays indoor ambient temperature.
● When selecting " " with remote controller, temperature indicator on indoor unit displays outdoor ambient temperature.
Note:
● Outdoor temperature display is not available for some models. At that time, indoor unit receives "
temperature.
● It's defaulted to display set temperature when turning on the unit.There is no display in the remote controller.
● Only for the models whose indoor unit has dual-8 display.
● When selecting displaying of indoor or outdoor ambient temperature, indoor temperature indicator displays corresponding temperature and
automatically turns to display set temperature after 3s or 5s.
9. I FEEL button
Press this button to start I FEEL function and "
will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the
detected temperature. Press this button again to close I FEEL function and "
● Do not put the remote controller near an object of high temperature or low temperature in order to avoid detecting inaccurate ambient
temperature.
10. LIGHT button
Press this button to turn off display light on indoor unit. "
display light. " " icon is displayed.
11. CLOCK button
Press this button to set clock time. "
pressing of "▲" or " " button, clock time will increase or decrease 1 minute. If hold "▲" or "
Release this button when reaching your required time. Press "CLOCK" button to confirm the time. "
Note:
● Clock time adopts 24-hour mode.
● The interval between two operations can't exceed 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER
OFF is the same.
12. TIMER ON / TIMER OFF button
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, "
blinks. Press "▲" or "
decrease 1min. Hold "▲" or "
confirm it. The word "ON" will stop blinking. "
started up, press "TIMER ON" button to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button,"
controller blinks. Press "▲" or "
TIMER OFF setting will increase or decrease 1min. Hold "▲" or "
required time. Press "TIMER OFF" word "OFF" will stop blinking. "
that TIMER OFF is started up, press "TIMER OFF" button to cancel it.
Note:
● Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the clock time.
● After starting up TIMER ON or TIMER OFF, the air conditioner will be turned on or turned off
according to setting time. ON/OFF button has no effect on setting. If you don't need this function, please use remote controller to cancel it.
20
" icon will disappear.
" will be displayed on the remote controller. After this function is set, the remote controller
" icon on remote controller will blink. Press "▲" or "
"button to adjust TIMER ON setting. After each pressing "▲" or "
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER ON" to
" icon resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
" button to adjust TIMER OFF setting. After each pressing "▲" or "
no display
" will disappear.
" icon on remote controller disappears. Press this button again to turn on
" icon disappears and the word "ON" on remote controller
" icon disappears and the word "OFF" on remote
" button, 2s later, the time will change quickly until reaching your
" icon resumes displaying. Cancel TIMER OFF. Under the condition
" icon is displayed on remote controller. Press this button
"signal, while it displays indoor set
" button within 5s to set clock time. Each
" button, 2s later, time will change quickly.
" icon stops blinking.
" button, TIMER ON setting will increase or
" button,
Service Manual
Technical Information