Advertisement
F
USING THE TIMERS
ON/OFF timer:
This enables radio programmed
to be recorded unat-
tended. CD play or tape playback can be started and
stopped
at the selected times.
WAKE UP timer:
This wakes you up to the sound of a CD, tape or radio.
SLEEP timer:
This allows you to fall asleep to the sound of a CD,
tape or radio.
Note:
Make absolutely
sure that the clock shows the correct
present time before setting any of the timers.
USING THE ON/OFF TIMER
First set the ON and OFF times and the source whose
sound is to be heard (for the tuner, select the band and
preset station).
Operation
will start with the selected
source at the ON time and the power will be switched off
at the OFF time.
'hetimersettings
are stored in the memory and retained
'=ven
when the timer operation
has been completed.
Each time the ON/OFF timer is to be actually operated,
set the unit to the standby
mode.
1. Set the timer ON/OFF times and the operation
mode.
(See "ON/OFF timer settings"
section.)
2. Prepare to hear the sources and prepare to record.
-
For CD play, load discs and select the disc num-
ber.
-
For tape playback,
load the tape into deck 1 or
deck 2. When tapes have been loaded into both
decks, deck 2 takes precedence.
-
For tape
recording/playback,
select the MODE
switch position which corresponds
to the record-
ing/playback
time, and set the DOLBY NR switch
as desired. Tape will start from the forward side.
- Turn down the VOLUME
control for unattended
recording.
3. Check the timer settings.
(See "To check the timer
settings"
section.)
--% Check that "TIMER ON OFF" (or "TIMER REC ON
OFF") is displayed, and then press the POWER switch
to turn off the power.
ON/OFF timer settings
1.
2.
3.
Press the TIMER sfitch.
The "TIMER ON" and previ-
ous timer ON time setting appear.
eg: TIMER
ON
1:10
PM
Press the MEMORY switch
before the 10 seconds
elapse. The "MEMORY"
and hours displays blink.
TIMER
ON
1:10
PM
MEMORY
Set the timer ON time by pressing the UP and DOWN
switches and then MEMORY switch (in the same way
as instructed
under "ADJUSTING
THE CLOCK').
TIMER
ON
10:20
PM
MEMORY -
TIMER
OFF
2:00
PM
MEMORY
The previous
timer OFF time setting
now appears,
and both the "TIMER OFF" and hours displays blink.
4. Set the timer OFF time in the same way as described
in step 3.
TIMER
OFF
11:00
PM
MEMORY -
TIMER
SOURCE
dlSC
MEMORY
The previous source setting display blinks.
5. Select the source
by pressing
the UP and DOWN
switches and then MEMORY switch.
-
Every time the UP switch is pressed,
the source
changes
in the following
sequence
(or in the re-
verse sequence
if the DOWN switch is pressed):
dlSC - TAPE - TU - TU REC - dlSC -...
6. Press the MEMORY switch. A return is made to the
original
display,
and the timer
operation
standby
mode is established.
("TIMER ON OFF" remains lit)
Note:
When the ON/OFF timer (or WAKE UP timer) is set for
the first time or when the memory contents have been
lost due to a power failure, " -:-
-" is displayed
for
both the ON and OFF times (or for the wake-uptime).
In cases like this, the MEMORY switch must be pressed
after
the
times
have
been set using the UP and
DOWN switches.
If the MEMORY switch is pressed
with the"
-:-
-" display remaining
unchanged,
"Err"
appears, the setting mode is released, and a return is
made to the original display.
The timer mode is released if a power failure occurs
during timer operation.
Also the UP and DOWN PRESET/APT
switches
can
be used for the setting timer.
With tuner reception or unattended
recording
The station for timer operation
must be preset.
1.
2.
3.
Perform step 5 above until "TU" blinks on the display.
TIMER SOURCE
TU
MEMORY
-
Select '[TU REC" in the case of unattended
record-
ing.
When the MEMORY switch
is pressed,
the band,
preset number and frequency
of the previous timer
operation
are displayed.
eg: TIMER
SOURCE
P
2
MW
594
kHz
MEMORY
Select the band using the BAND SELECT switch, and
indicate the desired preset number using the UP and
DOWN switches orthe[1]to[12]
number switches on
the remote controller,
TIMER SOURCE
P 2 FM 88.10 MHz MEMORY
Note:
When a preset number
cleared
has been selected,
" ----
" blinks. If the MEMORY switch is pressed then,
"Err"
appears,
the setting
mode is released
and a
return is made to the original mode.
Press the MEMORY switch. A return is made to the
original display.
(The "TIMER ON OFF" or "TIMER
REC ON OFF"
remains lit.)
-20-
Advertisement
