Advertisement
Relay playback (continuous
playback
on decks 1 and
2)
1. Load the tapes into both decks 1 and 2.
2, Set the MODE switch to"
~
".
3. Select the deck 1 or deck 2 by pressing
the DECK
select switch if required.
4. Press the PMY
or 4 PLAY switch.
-
Relay playback
will continue
from deck 1 (or 2) to
deck 2 (or 1) until the STOP switch is pressed.
[
Deck 1 forward side
Deck 1 reverse side
Deck 2 forward side
Deck 2 reverse side
Fast forwarding
and rewinding
Press the
w
or
44
switch. The
or 4
indicator
blinks.
When the tape has been wound to the end (or start), the
fast forward
or rewind function
will be automatically
released.
Note:
During cassette deck operation,
if an operating
problem
occurs, press the EJECT button and remove the cas-
sette. Reinsert it completely
and resume operation.
LISTENING TO THE RADIO
Memory operation
This unit enables
12 stations
FM, SW1, SW2 and MW
bands to be preset in the memory.
Manual presetting
1. Select the band (FM, SW1, SW2 or MW) using the
BAND SELECT switch.
2. Press the UP or DOWN switch to tune in the station.
For FM/MW reception:
Press the switch and release it as soon as the fre-
quency starts to change. The frequency
will change
continuously
until a station is tuned in, at which time
it will stop automatically
and the frequency
received
will be displayed.
- When the switch
is pressed
before a station
is
tuned in, the frequency
tuning will stop.
- When receiving a station with weak signals, press
the switch once and then again and again until the
station is received. Every time the switch is pressed,
the frequency
will change
in 9 kHz or 10 kHz
increments
for MW and 0.05 MHz increments
for
FM.
For SW1/SW2 reception:
This unit can be received only following
meter bands.
Swl
Meter band
Frequency
range
90 m
3.2- 3.4 MHz
75 m
3.9- 4.0 MHz
60 m
4.75-5.06
MHz
49 m
5.95 -6.2 MHz
41 m
7.1 -7.3 MHz
SW2
Meter band
Frequency
range
31 m
9.5-9.775
MHz
25 m
11.7 -11.975
MHZ
19m
15.1-15.45
MHz
16m
17.7 -17.9 MHz
13m
21.45-21.75
MHz
Press and hold down the UP or DOWN switch. When
you are close to the desired
frequency,
release it.
(When the switch is pressed for more than 3seconds,
the frequency
will change in 0.05 MHz steps.)
Press the switch once and then again and again until
the station is received. Every time the switch is pressed,
the frequency
will change in 0.005 MHz steps.
3. Press the MEMORY switch. "MEMORY"
blinks on the
tuner/timer
display.
4. Select the required preset number by pressing the UP
or DOWN PRESET/APT switch or one of the [1] to [1 2]
number switches
on the remote controller,
The fre-
quency
is replaced
by the preset
number
on the
display,
eg: MW
P 3
kHz
MEMORY
When the band is selected
by the controls on th -
main unit, check whether the [1] to [12] number-_
switches on the remote controller
are functioning
as preset tuning switches.
5. Re-press the MEMORY switch to preset the station.
"MEMORY"
disappears
and the display returns to the
original display.
If the next step is not taken within 30 seconds in the
steps "3" to "5", "MEMORY"
disappears.
In this
case, press the MEMORY switch again.
6. Repeat steps 1 (or2) to 5, and successively
preset the
stations.
Automatic presetting
(only for FM/MW reception)
1. Select the band.
2. Press and hold down both UP and DOWN PRESET/
APT switches for at least 3 seconds, until "MEMORY"
blinks,
The unit starts automatic
presetting
upwards
in fre-
quency from the low end of band.
3. When 12 stations have been preset or the high end or
band is reached, the automatic
presetting
will stop.
"MEMORY"
disappears
and the preset
number
1
station will be heard,
4. Select another band and repeat steps 2 and 3.
Clearing the memory
1.Select the band.
2. Select the preset number to be cleared by pressing
the UP or DOWN PRESET/APT switch or one of the [1 ]
to [12] number
switches.
The preset
number
ap-
pears,
3. Press the CLEAR switch while the preset number is
displayed
(within 2 seconds).
The preset station will
then be cleared from the memory
but the cleared
station will still be heard.
-15-
Advertisement
