Advertisement
Number switches
(O to 9, +1 O and [1]to[12])
All these switches are used to select both CD tracks and
preset radio stations.
If the CD 10KEY switch is pressed
then the switches
select CD track numbers.
If the BAND switch is pressed, the switches select preset
radio stations.
PREPARATIONS
FOR REMOTE CONTROL
OPERATION
Inserting batteries
1. Open the battery compartment
lid by pressing
the
latch.
2. Install 2 "AA/SUM-3/R6"
size batteries into the battery
compartment
matching
the polarity as shown in the
battery compartment.
3. Close the battery compartment
lid.
Note:
Always remove batteries
if the remote controller
is not
going to be used fora month or more. Batteries left in the
7 may leak and cause damage.
Remote control range
Use the remote controller within an angle of 30°tothe
Ietl
and right horizontally
and over distances
up to about 7
meters (Fig. 9).
ADJUSTING
THE CLOCK
The clock display blinks when the mains plug is inserted
into the AC outlet for the first time or when the pro-
grammed
details have been lost because
of a power
failure.
Example: To set "7:30PM",
1. Press the CLOCK switch for 1 or more seconds. The
"CLOCK'
and hours displays
blink.
eg: CLOCK
12:00
AM
f nothing further is done, the time setting mode will be
– released after 30 seconds.
2, Press the UP and DOWN switches to set the "hours."
CLOCK
7:00
PM
3. Press the MEMORY switch. The minutes display now
blinks.
CLOCK
7:00
PM
4, Press the UP and DOWN switches
to set the "min-
utes. "
CLOCK
7:30
PM
5. Press the MEMORY switch. The minutes display now
lights and the clock starts operating.
("CLOCK'
re-
mains lit.)
CLOCK
7:30
PM
- These operations
can be done, even if the POWER
switch is turned off.
- The UP and DOWN PRESET/APT switches can also
be used for setting the clock,
- The clock uses the 12-hour system (NOTE AM and
PM).
-
Every time the UP or DOWN switch is pressed, the
display will be incremented
ordecremented
by 1 hour
or 1 minute. If either switch is kept depressed,
the
display will be continuously
incremented
or decre-
mented until the switch is released,
- When the minutes
are being adjusted,
there is no
carry-over to the hour display.
- After the "minutes"
have been adjusted, the time can
be set accurately
by pressing
the MEMORY switch
when the time signal is heard.
-
Reset the time when the display blinks because of a
power failure. Reset the timer ON/OFF times as well.
The TIMER, WAKE UP and SLEEP switches
do not
function while the display is blinking,
- When the system has been powered for about a day,
the clock operation
and memory are backed
up as
follows.
- The clock operation
and memory are backed up
even with a power failure lasting few seconds.
- When a power failure lasts for more than few sec-
onds, the memory contents will be retained for half
a day but the clock display will blink,
BEFORE OPERATION
1. Turn down the VOLUME control so that the sound will
not suddenly
be delivered at a high level.
2. Press the POWER switch. To turn off the power, press
it again, "P.OFF"
appears on the tuner/timer
display
for 5 seconds.
- When the mains lead is connected
to the AC outlet,
the unit is set standby,
When the power is switched ON:
Tuner/Timer:
"Frequency
display"
appears
on the display.
(The
display which was indicated
before the power was
switched
off will appear.)
Amplifier:
The MOTOR DRIVEN CONTROL indicators
and one
of the function
indicators
light. (The function
which
was selected
before the power was switched
off is
selected.)
The display lights.
CD player:
If the function is "CD", the disc number and "no dlSC"
appears on the display. If discs have been placed on
the disc trays and a disc has been selected,
its disc
number, total number of tracks and total playtime will
be indicated.
With any other function,
the disc number
and "Cd
OFF" appears on the display.
WHAT TO DO IF ...
If the operation
and display do not function
correctly,
turn off the POWER switch of the main unit and then turn
it on again and repeat the operation.
If the power
is not turned
off even by pressing
the
POWER switch, disconnect
the mains lead from the AC
outlet. Then connect the lead to the AC outlet and repeat
the operation.
in this case, reset the clock and memory
contents.
-10-
Advertisement
