Advertisement
Random
play results when the RANDOM switch is
pressed during normal play.
When the RANDOM switch is pressed during random
play, operation moves to the next random programmed
track.
- The direct play mode is established
even when a
function other than CD has been previously selected.
Repeat play function
This unit has three different
repeat modes.
Press the
REPEAT switch repeatedly to select the desired mode in
the following
sequence.
The selected
repeat mode is
shown on the display,
"REPEAT ONE": Repeating
one track
"REPEAT ALL": Repeating
all the tracks of a disc
"REPEAT
CONTINUE":
Repeating
all the tracks of all
discs
None: Releasing all the repeat modes
The above three modes are effective for normal play,
intro play, random play and intro random play.
In programmed
play mode, only "REPEAT
ONE" and
"REPEAT ALL" modes are effective and the last setting
mode will always be effective.
Time display selection
During play, the remaining
playtime
on the disc which is
being played can be checked
using the TIME switch on
the remote controller.
- With programmed
play, the total remaining
time will
not be displayed.
-
[f the track number exceeds 32, the remaining times
for each track will not be displayed.
- The play times may not match the times listed on the
notes accompanying
the disc.
Every time the TIME switch
is pressed,
the display
changes in the following
sequence:
(Remaining
time for each track) -
(Total remaining
time) -- (Time played for each track)
When stopped,
total play time of the disc which has
been played is displayed.
PROGRAMMED
PIAY (using the remote controller)
The tracks (up to 32) on a disc can be played in any
desired sequence
whatsoever.
- The same tracks can be programmed
over and over
again.
- The tracks are programmed
in the stop mode of "CD"
function.
Programming
procedure
Proceed with the operation
after the CD 10KEY switch
has been pressed.
Example:
Programming
tracks 2 and 6 on DISC 1 and track 9 on
DISC 2
1. Press the MEMORY switch. "[PROG.]"
blinks on the
display, and the display indicates as:
eg: DISC 3 TRACK AL (all)
STEP 1 123
...
2. Select
DISC 1 by pressing
the DISC SKIP switch
repeatedly.
DISC 1 TRACK AL
STEP 1 123...
3.
4.
5.
6,
7.
8.
9.
Set track 2 which is to be played first by pressing the
number switch 2.
DISC 1 TRACK2
STEP 1 123...
Press the MEMORY switch. "[PROG.]"
remains lit.
DISC 1 TRACK 2 STEP 1 2
Set track 6 by pressing
the switch
6. "[PROG.]"
blinks.
DISC 1 TRACK 6 STEP 2 2
Press the MEMORY switch. "[PROG.]"
remains lit.
DISC 1 TRACK 6 STEP 2 26
Select DISC 2 by pressing
the DISC SKIP switch.
"[PROG.]"
blinks.
DISC 2 TRACK AL
STEP 3
Set track 9 by pressing the switch 9.
DISC 2 TRACK 9 STEP 3
Press the MEMORY switch. "[PROG.]"
remains lit.
DISC 2 TRACK 9 STEP 3
9
The tracks can also be selected using the K
or w
switch.
When programming
using the controls
on the main
unit, use the disc select switches to assign the discs
and the SKIP/SEARCH
switches to assign the tracks.
Anv attempt to Proqramme
more than 32 tracks v ""
re&dt in "FULL''"bei;g
displayed
and discontinuatiO_rl
of the programming.
Proaramme
checking and play
1.
2.
E;ety time the MEMORY swi~ch is pressed once, the
programmed
details (disc number, track number and
their play sequence)
appear on the display.
- These displays will not appear during programmed
play.
Programmed
play is started when the E/11 switch is
pressed,
The stop mode is established
when the track pro-
grammed last has been played through.
(In this case,
the programme
is not cleared but remains.)
During programmed
play, if the programmed
track
does not exist on the disc, the display
shows
"PErr"
(programme
error) and then the next pro-
gramme will be played.
Note:
The programme
is cleared in the following
cases:
- When the
switch is pressed in the stop mode
- When the EDIT switch is pressed in the stop mode
- When the mains lead has been disconnected
Revising or correcting a programme
(Adding onto a programme)
1. Press the MEMORY switch in the stop mode, search
for the end of the programme
and display"-
---
,,
-. ---m
2. Assign the desired disc by pressing
the DISC SKIP
switch. " [PROG,]"
blinks.
3. Use the Oto 9 and +1 Oswitches (or the 144 and WI
switches) to select the number of the track which is to
be added.
4. Press the MEMORY switch. "[PROG.]"
remains lit.
-13-
Advertisement
