Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Proteco MOVER 5
Summary of Contents for Proteco MOVER 5
- Page 1 Installation Manual MOVER OPENER FOR RACK-DRIVEN SLIDING MOTOR...
-
Page 3: Table Of Contents
Index WARNINGS AND GENERAL SAFETY INSTUCTIONS .................... pag. 01 DICHIARAZIONE DI CONFORMITA’ ........................pag. 01 PRODUCT DESCRIPTION AND INTENDED USE ....................pag. 01 TECHNICAL SPECIFICATIONS ........................pag. 02 PACK CONTENTS ............................ pag. 02 DIMENSIONS ............................. pag. 02 INSTALLATION ..............................pag. 03 Preliminary Checks .......................... -
Page 4: Warnings And General Safety Instuctions
Use exclusively original parts by manufactured by Proteco for maintenance. Do not carry out any alteration on the components of the automatic gate. Proteco SRL will not accept liability for any components and/or additional devices used in-conjunction with the automation that has not been produced exclusively by Proteco. -
Page 5: Technical Specifications
Technical Specifications CAT 5 CAT 8 CAT 5 115V CAT 8 115V MOVER 5 MOVER 8 MOVER 15 MOVER 15T MOVER 5 115V MOVER 8 115V MOVER 15 115V 230V~50-60Hz 230V~50-60Hz 230V~50-60Hz 380V 115V ~ 50-60Hz 115V ~ 50-60Hz 115V ~ 50-60Hz... -
Page 6: Installation
INSTALLATION Preliminary Checks Before the installation, to ensure correct working of the automation, please check the followings: • Make sure the gate’s structure is suitable to be automated • Check the weight, dimensions and type of the gate is appropriate to this type of automation. •... -
Page 7: Preliminary Installation Work And Masonry For Anchor Plate
Preliminary installation work and masonry for Fig. 2 anchor plate Check the fixing height of the rack on the gate and calculate the height of concrete baase for the mtor accordingly a) Dig the foundation pit for the gear motor whilst considering the anchor plate dimensions. -
Page 8: Assembling The Rack
Assembling the rack Fig. 9 3.5.1 Installing the Toothed Rack B117 – PVC rack M4 20x26mm with inner steel frame (0.5m sections) a) Move the gate manually to its open position. b) Align the first section of the rack to the gate edge and lower it on the pinion. -
Page 9: Welding Metal Toothed Rack B102
Assembling the limit-switch brackets Fig. 14 3.6.1 PVC brackets for Toothed Rack B117 a) IIdentify closing and opening brackets according to the motor position against the gate (Fig. 14). OPENING CLOSING limit-switch limit-switch b) Manually close the gate up to 3cm before the closing mechanical stop. -
Page 10: Assembling The Chain
Fig. 18 Fig. 19 Click Click Motor on the RIGHT Motor on the RIGHT OPENING limit-switch CLOSING limit-switch Once the assembling of the limit brackets to rack is completed, open and close the gate manually to check that the brackets always activate the limit-switch system before the gate reaches its mechanical stops. This checking is important to preserve the correct working of the automation and continued good mechanical condition of the gate. -
Page 11: Limit-Brackets Fixing For Chain-Driving Motor
Fig. 25 3.7.1 Limit-brackets fixing for chain-driving motor OPENING CLOSING Please pay attention when fixing limit-brackets, once fixed to the gate no further adjustments are possible. limit-switch limit-switch We recommend the following procedure: a) Drive the gate manually to almost complete open/close position, make sure that the gate don't touch its mechanical stop yet. -
Page 12: Release Procedure For Manual Operation
Any components displaying significant wear should be obtained from Proteco or associated agents and replaced immediately. DISPOSAL Do not pollute the environment Some components may contain polluting substances. - Page 13 01_2015...
- Page 14 Proteco S.r.l. Via Neive, 77 - 12050 CASTAGNITO (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 - info@proteco.net - www.proteco.net...