Automation system for counterweight balanced (up and over) garage doors (12 pages)
Summary of Contents for Proteco Q80S
Page 1
24 Vac, max 20 W Accessories power supply 24 Vdc , max 5 W Working temperature -20 +50 °C PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Frequently examine the installation for signs of wear or damage to cables. Do not use if repair or adjustment is needed. Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
15 16 17 ALIM. 230Vac PEDESTRIAN BLACK STOP START POLE DISCONNECT DEVICE COMMON 230V CLOSING OPENING PHOTOCELLS PHOTOCELLS PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Page 6
Pole disconnect means must be incorporated in the fixed wiring to the control panel J5 = plug for optional modules Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
In case of gate opening from right to left please adjust parameter accordingly to 01 (see page 16). Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Should you need to temporary exclude the OPENING PHOTOCELLS connections, please set parameter in the ACCESSORIES menu to =DISABLED. 10 11 Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
To select this mode, please set the dip-switches on the module as shown: 1= ON 2= OFF 3= ON Dip-switch 4 is non influential. Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
If further adjustments of the sensibility level for obstacle detection are needed, please refer to setting in the FORCE menu. Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
In case of fault of the limit switches the motor will stop running in any case after 120 seconds. Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Ensure materials are passed to the authorised collection centres, according to the laws and the regulations on force, for safe disposal. Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
= flashing = FIX (LED) DEAD MAN’S SWITCH mode = STANDARD mode = DEAD MAN’S SWITCH mode Q80S_2014 PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Page 28
Programming settings have been saved Rotating segments: motors running Small dots: brightness of the dot is proportional to the force settings PROTECO S.r.l. Via Neive, 77 - 12050 Castagnito (CN) ITALY Tel. +39 0173 210111 - Fax +39 0173 210199 info@proteco.net - www.proteco.net...
Page 29
COMPLIANCE DECLARATION Manufacturer: PROTECO S.r.l. Address: Via Neive, 77 – 12050 Castagnito (CN) – ITALIA declares that The product type: Q80A electronic controller for sliding gate automation (1 motor), 220V Models: PQ80S Accessories: MRX01 Is built to be integrated into a machine or to be assembled with other machinery to crate a machine under provisions of 2006/42/EC Machinery Directive.