Table of Contents
Advertisement
1.
WARNINGS AND GENERAL SAFETY INSTUCTIONS
This manual contains important safety information.
An incorrect installation or an improper use may cause serious damages to persons or objects.
Read this manual carefully and completely. Pay particular attention to the sections marked by the symbol:
This indicates that risk to personal injury may occur if not adhered to.
Store this manual safety for future use.
Always disconnect main power supply before operating in the automatic gate.
Make sure that the earth system is perfectly working and always connect the automatic gate to it.
The installation of automatic gates and doors must fully comply with the requirements set forth in 2006/42/EC Directive, with particular
reference to EN 12445 and EN 12453 standards.
The final connection to the electrical mains, testing and start-up of the automation must be performed by skilled and qualified personnel
(professional gate installers), who is responsible for carrying out the risks analysis and verifying the compliance of the system with the
current safety standards.
This product is exclusively designed and manufactured for the intended use specified in this manual.
Any other use than stated could compromise the integrity and the safety of the product and therefore is strictly prohibited.
The automation is designed to move driveway gates and not intended to be used for any other purpose.
Do not let children play with the radio transmitters and any other device which could accidentally start the gate automation.
Use exclusively original parts by manufactured by Proteco for maintenance.
Do not carry out any alteration on the components of the automatic gate.
Proteco SRL will not accept liability for any components and/or additional devices used in-conjunction with the automation that has not
been produced exclusively by Proteco.
EU DECLARATION OF CONFORMITY AND DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
hereby declare that the products listed below:
MOVER 5, MOVER 8, MOVER 15, MOVER 15 T, CAT 5 , CAT 8
MOVER 5 110V, MOVER 8 115V, MOVER 15 115V, CAT 5 115V , CAT 8 115V
Electromechanical gearmotor for rack/chain-driven slidng gate and accessories
comply the following Essential Requirements of directive 2006/42/CE Allegato I (direttiva Macchine):
1.1.2 - 1.1.3 - 1.1.5 - 1.2.1 - 1.2.2 - 1.2.3 - 1.2.6 - 1.3.2 - 1.3.4 - 1.3.9 - 1.4.1 - 1.4.2.1 -1.5.1 - 1.5.4 - 1.5.6 -1.5.8 - 1.5.13 - 1.6.1 - 1.6.4 - 1.7.1 1.7.3 1.7.4
are in conformity with the following derectives:
2004/108/CE (electromagnetic compatibility)
1999/5/CE (R&TTE)
2011/65/CE (directive on the restriction of the use of certain hazardous substances in electrical and electronic equipmemt)
The above listed products are delivered, limitedly to the applicable parts, according to the following standards:
- EN 12453
Industrial, commercial and garage doors and gates. Safety in use power operated doors. Requirements.
- EN 12445
Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Test methods.
- EN60335-1
Household and similar electrical appliances - Safety - Part 1: General requirements.
- EN60335-2-103
Household and similar electrical appliances - Safety - Part 2-103: Particular requirements for drives for gates, doors and windows.
They also state that:
- the relevant technical documentation is compiled in accordance with part B of Annex VII of directive 2006/42/CE
- the relevant technical documentation is compiled and preserved by Proteco S.r.l.
Which undertakes to transmit it by mail in response to a reasoned request by the national authorities.
- the partly completed machinary must not be put into service until the final machinery into which it is to be incorporated has
been declared in conformitywith the provisions of the dorective 2006/42/CE
Castagnito, 19/01/2016
2.
PRODUCT DESCRIPTION AND INTENDED USE
MOVER gear motor is designed to automate residential or commercial sliding gate with rack.
Any other use than above described has to be considered as inappropriate and strictly prohibited.
All models feature an irreversible gearing system that locks the gate when it is in its fully closed position.
Therefore no additional lock is needed.
In case of a power failure the motor lock can be released to move the gate manually (see section 6).
1
In accordance with Annex II B of Machinery Directive 2006/42/CE
The legal representatives of
Proteco S.r.l.
via Neive 77, 12050 Castagnito (CN) Italia
tel (+39) 0173210111 - fax (+39) 0173210199
www.proteco.net - info@proteco.net
.
Marco Gallo
Managing Director
01_2015
Hide quick links:
Advertisement
Table of Contents
