ADJ Encore Profile 1000 Color User Instructions page 5

Encore Profile 1000 Color
6. After you have adjusted the RGBW colors to make your desired
color you can then activate strobing by pressing the SET UP but-
ton to enter strobing.
7. "STRO" will be displayed, this is strobing mode. The strobing can
be adjusted between "00" (strobing off) to "15" (fastest strobing).
Color Change Mode:
1. Plug the fixture in and press the MODE button until "JUMP RUN
SNAP:XX" is displayed. "XX" represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color change
mode.
3. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color
change. The speed can be adjusted between "01" (slowest) to
"16" (fastest).
Color Fade Mode:
1. Plug the fixture in and press the MODE button until "FADE RUN
FADE:XX" is displayed. "XX" represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade
mode.
3. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the color fade.
The speed can be adjusted between "01" (slowest) to "16" (fast-
est).
Auto Run Mode:
1. Plug the fixture in and press the MODE button until "AUTO RUN
FAD+SNAP" is displayed.
2. Press the SET UP button and "SPEED:XX" will be displayed. Use
the UP and DOWN buttons to adjust the speed of the Auto Run.
The speed can be adjusted between "01" (slowest) to "16" (fast-
est).
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLR MACS
COLOR:XX" is displayed. "XX" represents a number between
00-64.
2. Use the UP and DOWN buttons to scroll through the 64 colors
and find you desired color. After you have found your desired
ADJ Products, LLC - www.adj.com - Encore Profile 1000 Color User Manual Page 8
Operating Instructions Encore Profile 1000 Color
color you can activate strobing by pressing the SET UP button to
enter the strobe mode.
3. "STROB:XX" will be displayed, this is strobe mode. The strobing
can be adjusted between "00" (flash off) to "15" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
The Encore Profile 1000 Color has 5 DMX modes: 4 channel mode,
5 channel mode, 6 channel mode, 10 channel mode, and 11 channel
mode. See page's 17-23 for each mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"DMX MODE:XXX" is displayed. "XXX" represents the current
displayed DMX address. Use the UP or DOWN buttons to select
your desired DMX address, then press the SETUP button to select
your DMX channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX channel
modes. The channel modes are listed below:
• "CHAN: 04" is 4 Channel DMX Mode.
• "CHAN: 05" is 5 Channel DMX Mode.
• "CHAN: 06" is 6 Channel DMX Mode.
• "CHAN: 10" is 10 Channel DMX Mode.
• "CHAN: 11" is 11 Channel DMX Mode.
4. Please see pages 17-23 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
System Reset:
This will return the fixture to its factory settings.
1. Plug the fixture in and press the MODE button until "OTHER
MODE" is displayed.
2. Press the SET UP button until "SYSRESET" is displayed.
3. Press the UP and DOWN buttons simultaneously to reset or press
the MODE button to exit.
ADJ Products, LLC - www.adj.com - Encore Profile 1000 Color User Manual Page 9
Operating Instructions