Nordson Vantage Customer Product Manual
  1. Manuals
  2. Brands
  3. Nordson Manuals
  4. Paint Sprayer
  5. Vantage
  6. Customer product manual
Nordson Vantage Customer Product Manual

Nordson Vantage Customer Product Manual

Manual powder spray gun
Hide thumbs Also See for Vantage:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Customer Product Manual
r
Vantage
Manual Powder Spray Gun
Customer Product Manual
Part 1070278-04
Issued 04/16
For parts and technical support, call the
Finishing Customer Support Center at (800) 433-9319.
This document is subject to change without notice.
Check http://emanuals.nordson.com/finishing for the latest version.
NORDSON CORPORATION • AMHERST, OHIO • USA

Advertisement

Table of Contents
loading

Related Manuals for Nordson Vantage

Summary of Contents for Nordson Vantage

  • Page 1 Customer Product Manual Part 1070278-04 Issued 04/16 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change without notice. Check http://emanuals.nordson.com/finishing for the latest version. NORDSON CORPORATION • AMHERST, OHIO • USA...

  • Page 2: Table Of Contents

    ....Contact Us Notice This is a Nordson Corporation publication which is protected by copyright. Nordson Corporation welcomes requests for information, comments, and Original copyright date 2006. No part of this document may be inquiries about its products.

  • Page 3: Part

    Change Record Change Record Revision Date Change 04/16 Removed approval label and DOC. Part 1070278-04 E 2016 Nordson Corporation...
  • Page 4 Change Record Part 1070278-04 E 2016 Nordson Corporation...

  • Page 5: Safety

    Any approvals Read and follow these safety instructions. Task- and equipment-specific warnings, cautions, and obtained for Nordson equipment will be voided if instructions for installation, operation, and service instructions are included in equipment documentation where appropriate.

  • Page 6: Fire Safety

    Use only replacement parts that are designed grounding strap connected to the gun handle or for use with original equipment. Contact your other true earth ground. Nordson representative for parts information Shut off electrostatic power supplies and and advice. ground gun electrodes before making adjustments or cleaning powder spray guns.

  • Page 7: Description

    (multiplier) is user-replaceable. The spray gun is as it exits the nozzle, and the electrostatic field used with the Vantage Manual Spray Gun Control generated between the electrode and the grounded Unit and a standard or low-flow powder pump. The workpiece.

  • Page 8: Installation

    (Blue) 0−7 BAR NOTE: Tighten the gun cable retaining nut to 6 NSm (4.4 ft-lb). An optional 4-meter extension cable is available. Do not add more than two extension cables to the gun cable. Part 1070278-04 E 2016 Nordson Corporation...
  • Page 9 C. Hopper 3. Blue, 8-mm air tubing (atomizing) 7. POWER INPUT cable D. Spray gun 4. Black, 8-mm air tubing (flow rate) 8. Blue, 10-mm air tubing (IN) Note: Typical powder pump and hopper shown. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 10: Operation

    Remove the O-rings first. and electrostatic setpoints as described in the Do not immerse the spray gun in alcohol. Do control unit manual. not use any other solvents. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 11: Weekly Maintenance

    Figure 3 Daily Maintenance 1. Extension 4. Wear sleeve 7. Set screw 2. Resistor probe 5. Conical nozzle 8. Hose adapter 3. Powder inlet body 6. Deflector Part 1070278-04 E 2016 Nordson Corporation...

  • Page 12: Troubleshooting

    These procedures cover only the most common problems that you may encounter. If you cannot solve the problem with the information given here, call the Nordson Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative for help.
  • Page 13 Failed gun resistor Check the resistor with a megohmmeter for 153−187 megohms at 500 volts. Malfunctioning control unit Check for 21 Vdc between pins 2 and 3 (spray gun end of cable) with the trigger depressed. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 14: Continuity And Resistance Checks

    153 and 187 megohms at 500 volts. If the reading is out of this range, replace the resistor probe. Figure 5 Multiplier/Resistor Assembly Resistance Check 1. Electrode 3. Spring contact 2. Resistor probe 4. Multiplier Part 1070278-04 E 2016 Nordson Corporation...

  • Page 15: Gun Cable Continuity Checks

    1 and 2 Close trigger switch Negative (Common) Positive (+21 Vdc) μA Feedback Open Ring-tong terminal Ground Blue Gun End Yellow 1 2 3 NORDSON Green Control Unit End Figure 6 Gun Cable Continuity Checks Part 1070278-04 E 2016 Nordson Corporation...

  • Page 16: Repair

    (5) that secure the hanger (17) to the extension and remove the hanger. Install the hanger on the new extension. 9. Perform the disassembly steps in reverse to install the new multiplier/resistor probe assembly in your spray gun. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 17: Contact Tip Replacement

    2. See Figure 8. Unscrew the damaged contact tip (1) from the end of the resistor probe (2). 3. Apply dielectric grease to the threads of the new contact tip and into the end of the probe. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 18: Resistor Replacement

    Contact Tip and Resistor Replacement 1. Contact tip 3. Resistor spring 5. Multiplier well 2. Resistor probe 4. Multiplier 6. Resistor probe cavity Note: Clean item 5, grease items 1, 3, 5, and 6. Part 1070278-04 E 2016 Nordson Corporation...

  • Page 19: Parts

    The number in the Part column is the Nordson Corporation part number. A series of dashes in this column (- - - - - -) means the part cannot be ordered separately.

  • Page 20: Gun Parts

    S BRACKET, cable/tube retaining 982098 S SCREW, fillister head, slotted, M4 x 0.7 x 6 - - - - - - S CABLE, manual gun, Vantage, 6 meter 1070246 S SCREW, pan head, #2-56 x 0.437 in., slotted, zinc 983113...
  • Page 21 Vantager Manual Powder Spray Gun Figure 9 Gun Parts Part 1070278-04 E 2016 Nordson Corporation...

  • Page 22: Service Kits

    S SCREW, pan head, #2-56 x 0.437 in., slotted, zinc 983113 S WASHER, lock, split, 2, steel, zinc 983510 S WASHER, flat, 0.094 x 0.188 x 0.025 in., brown Figure 10 Cable Service Kit Part 1070278-04 E 2016 Nordson Corporation...

  • Page 23: Multiplier Service Kits

    S SERVICE KIT, holder, resistor 125613 S EXTENSION NOTE A: Standard multiplier shipped with the spray gun. B: Optional multiplier used to give powder particles a positive charge. Contact your Nordson representative or powder supplier for more information. Figure 11 Multiplier Service Kits Resistor Service Kit See Figure 12.

  • Page 24: Handle Service Kit

    SERVICE KIT, trigger 132334 S PIVOT, trigger 125617 S TRIGGER, hand gun, modular 133783 S SPRING, trigger, return 982370 S SCREW, pan head, slotted, M2 x 5 Figure 13 Handle and Trigger Service Kits Part 1070278-04 E 2016 Nordson Corporation...

  • Page 25: Shorting Plug

    POWDER TUBING, 11 mm ID, blue 900649 POWDER TUBING, 9.5 mm ( in.) ID, blue Options Contact your Nordson representative for more information about these options. Option Descriptions Option Description Nozzles and Deflectors Nozzles and deflectors are available in a variety of sizes and configurations.

  • Page 26: Option Part Numbers

    450-mm LANCE EXTENSION Ion Collectors 189492 KIT, handgun, ion collector 189493 KIT, 150-mm lance, ion collector 189494 KIT, 300-mm lance, ion collector Miscellaneous Options 183468 KIT, cup gun 1083221 CABLE, manual gun, 6 meter extension Part 1070278-04 E 2016 Nordson Corporation...

  • Page 27: Optional Nozzles

    134384 4-mm 141044 141045 3-mm 139935 139902 O-Ring 940084 6-mm 139937 139903 O-Rings 941181 141013 141017 60_ Cross-Cut Wear Sleeve 134385 141014 141015 90_ Cross-Cut Figure 15 Common Flat-Spray Nozzle Parts Castle 147495 147877 Part 1070278-04 E 2016 Nordson Corporation...

  • Page 28: Conical Nozzle And Deflector Selection

    Versa-Spray II Large Medium surfaces 26 mm Short Versa-Spray II Parts with Medium- gaps and recesses 26 mm 32 mm with Parts with pattern Medium- gaps and adjuster recesses 38 mm 45 mm Large surfaces Part 1070278-04 E 2016 Nordson Corporation...

  • Page 29: Conical Nozzle And Deflector Parts

    16-mm DEFLECTOR, Tivar, with O-ring 133714 19-mm DEFLECTOR, Tivar, with O-ring 940084 S O-RING, silicone, 0.188 x 0.312 x 0.063 in. NOTE A: This O-ring is included with all deflectors. Figure 16 32-mm Conical Nozzle and Deflectors Part 1070278-04 E 2016 Nordson Corporation...
  • Page 30 NOZZLE, short, with O-rings 941181 S O-RING, silicone, 0.875 x 1.063 x 0.094 in. 132348 SLEEVE, wear, conical NOTE A: This O-ring is included with all deflectors. Figure 18 Short Conical Nozzle and Deflectors Part 1070278-04 E 2016 Nordson Corporation...

Table of Contents