Cisco Catalyst 2960 Command Reference Manual page 547
Hide thumbs
Also See for Catalyst 2960:
- Configuration manual (2288 pages) ,
- Software configuration manual (980 pages) ,
- Command reference manual (800 pages)
Table of Contents
Advertisement
Chapter 2 Catalyst 2960 Switch Cisco IOS Commands
Table 2-35
Media Type
Ethernet
FDDI
FDDI-NET
Token Ring
Token Ring
concentrator
relay function
(TrCRF)
Token Ring-NET VTP v1 mode is enabled.
Token Ring
bridge relay
function (TrBRF)
Table 2-36
Table 2-36
Configuration
VTP v2 mode is enabled, and you
are configuring a TrCRF VLAN
media type.
VTP v2 mode is enabled, and you
are configuring VLANs other than
TrCRF media type.
78-16882-01
Valid Syntax for Different Media Types
Valid Syntax
vlan vlan-id [name vlan-name] media ethernet [state {suspend | active}]
[said said-value] [mtu mtu-size] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
vlan vlan-id [name vlan-name] media fddi [state {suspend | active}]
[said said-value] [mtu mtu-size] [ring ring-number] [parent parent-vlan-id]
[tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
vlan vlan-id [name vlan-name] media fd-net [state {suspend | active}]
[said said-value] [mtu mtu-size] [bridge bridge-number]
[stp type {ieee | ibm | auto}] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
If VTP v2 mode is disabled, do not set the stp type to auto.
VTP v1 mode is enabled.
vlan vlan-id [name vlan-name] media tokenring [state {suspend | active}]
[said said-value] [mtu mtu-size] [ring ring-number] [parent parent-vlan-id]
[tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
VTP v2 mode is enabled.
vlan vlan-id [name vlan-name] media tokenring [state {suspend | active}]
[said said-value] [mtu mtu-size] [ring ring-number] [parent parent-vlan-id]
[bridge type {srb | srt}] [are are-number] [ste ste-number]
[backupcrf {enable | disable}] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
vlan vlan-id [name vlan-name] media tr-net [state {suspend | active}]
[said said-value] [mtu mtu-size] [bridge bridge-number]
[stp type {ieee | ibm}] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
VTP v2 mode is enabled.
vlan vlan-id [name vlan-name] media tr-net [state {suspend | active}]
[said said-value] [mtu mtu-size] [bridge bridge-number]
[stp type {ieee | ibm | auto}] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id]
describes the rules for configuring VLANs.
VLAN Configuration Rules
Rule
Specify a parent VLAN ID of a TrBRF that already exists in the
database.
Specify a ring number. Do not leave this field blank.
Specify unique ring numbers when TrCRF VLANs have the same
parent VLAN ID. Only one backup concentrator relay function
(CRF) can be enabled.
Do not specify a backup CRF.
vlan (VLAN configuration)
Catalyst 2960 Switch Command Reference
2-519
Advertisement
Table of Contents
