1. Manuals
  2. Brands
  3. Eiki Manuals
  4. Projector
  5. EK-800U
  6. Service manual

Eiki EK-800U Service Manual

Hide thumbs Also See for EK-800U:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Manual

SERVICE MANUAL

EK-800U
Date
Revise Version
Description
2016.01.11
V1.0
Initial Issue
Copyright January 2016 All Rights Reserved
(C) 2016 EIKI Industrial Inc,

Advertisement

Table of Contents
loading

Related Manuals for Eiki EK-800U

Summary of Contents for Eiki EK-800U

  • Page 1: Service Manual

    SERVICE MANUAL EK-800U Date Revise Version Description 2016.01.11 V1.0 Initial Issue Copyright January 2016 All Rights Reserved (C) 2016 EIKI Industrial Inc,...
  • Page 2 Preface This manual is applied to EK-800U projection system.The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products.We expect your customers will appreciate the service that you offer them.

  • Page 3: Table Of Contents

    2-30 Remove the DMD,DMD Board 2-31 Remove the Color Wheel Docking Board 2-33 Remove the AC Inlet 2-34 Remove the Power Supply 2-35 Remove the Fan 7 and Fan 10 2-36 Remove the bottom cover 2-37 Repair Action 2-38 EK-800U...
  • Page 4 3-13 Network Troubleshooting 3-14 Chapter 4 Test & Inspection Test Equipment Needed Service Mode and Factory Mode Factory Reset Calibration Adjustment 4-11 Chapter 5 Firmware Upgrade Formatter/Scalar/LAN/MCU Firmware Upgrade Recovery Mode Re-write Serial Number 5-11 Appendix A Exploded Image EK-800U...

  • Page 5: Highlight

    I/O Terminal • R/G/B/H/V, Y/Pb/Pr: • BNC x 5 • VGA: • D-sub 15 pin x 1 • Video: • BNC x 1 • VGA (Out): • D-sub 15 pin x 1 • 3D Sync: • BNC x 1 EK-800U...
  • Page 6 • Color type (Optional): 6 segments (Y41 type) • 0~40 degree • 0~2500 ft: 0~40 degree Operating Temperature • 2500~5000 ft: 0~35 degree • 5000~10000 ft: 0~30 degree Note:Measurement,measuring conditions and method of notation all comply with ISO 21118 international standards. EK-800U...

  • Page 7: Chapter 2 Disassembly Process

    4. Hex Sleeves 5 mm 5. Hex Sleeves :14.0 mm 6. Needle-nose pliers 7. Projector * Caution: -This process is protective level II. Operators should wear electrostatic chains. -The unit should be powered down and disconnected from mains. -When disassemble Engine module (2-18), please notice that it require specific environmental conditions (clean room). EK-800U...

  • Page 8: Disassemble Projector Lens

    Chapter 2 Disassembly Process 2-2 Disassemble Projector Lens 1. Press and hold on the lens bar. 2. Hold on projector lens, rotate it carefully (As red arrow), then remove it carefully. lens EK-800U...

  • Page 9: Remove The Fan 1 And Fan

    1. Open the lamp cover module to loosen two captive screw. 2. Remove the lamp cover module. 3. Loosen four screws and unplug two connectors to remove the fan 1 and fan 2. 4. Disconnect the extended wire then separate the outlet vent cover and fan. EK-800U...
  • Page 10 5. Tear off two rubbers to separate fan 1 and fan 2. Note:Fan 1 and fan 2 are the same. 6. Unscrew two screws to remove the fan docking board. Fan docking board 7. Replace the rear cover if required. Rear cover EK-800U...

  • Page 11: Remove The Lamp 1 And Lamp 2 Module

    Chapter 2 Disassembly Process 2-4 Remove the Lamp 1 and Lamp 2 Module 1. Loosen three captive screws to remove lamp 1 module. lamp1 2. Loosen three captive screws to remove lamp 2 module. lamp2 EK-800U...

  • Page 12: Remove The Color Wheel Module

    Chapter 2 Disassembly Process 2-5 Remove the Color Wheel Module 1. Loosen one screw to open the Color wheel cover. CW cover 2. Loosen three captive screws to take out the color wheel module. Color wheel EK-800U...

  • Page 13: Remove The Fuse

    Chapter 2 Disassembly Process 2-6 Remove the Fuse 1. Remove the fuse holder by rotating it counter-clockwise. 2. Take out the fuse holder. 3. Separate the holder and fuse. Fuse EK-800U...

  • Page 14: Remove Top Cover

    Chapter 2 Disassembly Process 2-7 Remove Top Cover 1. Loosen four captive screws first. 2. Pull the top cover ahead to remove top cover module. Note:There are eight snaps under the top cover module. Top cover EK-800U...

  • Page 15: Remove Main Board

    Chapter 2 Disassembly Process 2-8 Remove Main Board 1. Remove ten (yellow) screws securing top shielding. 2. Remove nine hex screws ,two captive screws (red) and one hex screw (yellow). 3. Cut off the cable tie. EK-800U...
  • Page 16 Chapter 2 Disassembly Process 4. Remove nine screws (yellow) and unplug twenty one connectors (red) to remove formatter board module. R S T EK-800U 2-10...
  • Page 17 J53 TO FAN BD (30pin) White Connector and Black wire tube J18 LAMP2 (5 pin) White Connector and Black wire tube J17 LAMP1 (5 pin) Composed of White/Yellow/Red/Black/ J40 H-SENSOR Gary Wire, White Connector and Black wire tube (5 pin) EK-800U 2-11...
  • Page 18 J62 DET Wire, White Connector and Blue wire tube (4 pin) Composed of Black/Red/White/Blue/ J63 DET Wire, White Connector and Blue wire tube (4 pin) Composed of Black/Red/White/Blue/ J64 DET Wire, White Connector and Blue wire tube (4 pin) EK-800U 2-12...
  • Page 19 8. Remove two connectors securing main board module, then separate the input cover. 9. Loosen three screws and unplug two connectors to separate formatter board. Note: There are two connectors between formatter board and scalar board. Formatter board EK-800U 2-13...
  • Page 20 Chapter 2 Disassembly Process 10. Loosen three screws (red) and remove three standoffs (yellow) to separate the scalar board and PW808 media board. PW808 board 11. Remove three hex standoffs. Scalar board EK-800U 2-14...
  • Page 21 Chapter 2 Disassembly Process 12. Remove nine screws securing the main board bottom shielding. EK-800U 2-15...

  • Page 22: Remove The

    Chapter 2 Disassembly Process 2-9 Remove the front cover and components 1. Pull down the filter cover then take out it. 2. Remove five screws, tear off 3M tape, sponge and take out the cable from hole then securing the shielding. EK-800U 2-16...
  • Page 23 Chapter 2 Disassembly Process 3. Remove six screws securing the front cover module. 4. Remove four screws then separate two switchs. 5. Take out two IR sensor boards from the front cover. interlock switch IR sensor board Front cover EK-800U 2-17...

  • Page 24: Remove The Back Cover

    Chapter 2 Disassembly Process 2-10 Remove the Back Cover 1. Remove ten screws securing the back shielding. 2. Remove twelve screws. 3. Remove two screws and one connector then take out the rear cover module. EK-800U 2-18...
  • Page 25 4. Remove two screws . 5. Unplug one connectors to separate the LED board and cable. LED board 6. Unplug four connectors and remove two screws to take out the fan 3 and interlock switch. Fan 3 Interlock switch EK-800U 2-19...
  • Page 26 Chapter 2 Disassembly Process 7. Remove two screws . 8. Unplug one connectors to separate the rear cover connector board and cable. Rear cover connector board Rear cover EK-800U 2-20...

  • Page 27: Remove The Left Cover

    Chapter 2 Disassembly Process 2-11 Remove the Left Cover 1. Remove six screws securing the left cover. 2. Remove two screws to disassemble the interlock switch. Left cover EK-800U 2-21...

  • Page 28: Remove The Keypad

    Chapter 2 Disassembly Process 2-12 Remove the Keypad 1. Remove two screws securing the keypad cover. 2. Remove six screws and one connector to disassemble the keypad board. keypad board EK-800U 2-22...

  • Page 29: Remove The Right Cover And Fan

    Chapter 2 Disassembly Process 2-13 Remove the Right Cover and Fan 4 1. Remove six screws securing the right cover. Right cover 2. Loosen three screws to remove the fan 4 module. EK-800U 2-23...

  • Page 30: Remove The Lamp Driver

    4 and bracket. Fan 4 2-14 Remove the lamp driver 1. Cut off the cable tie (red), unplug six connectors and ten screws. 2. Pull out the lamp driver 2 module then remove three connectors. EK-800U 2-24...
  • Page 31 Chapter 2 Disassembly Process 3. Loosen three screws to remove fan driver board. Fan driver board 4. Separate the bracket and Lamp driver 2 from four spacer supports. Lamp driver 2 EK-800U 2-25...
  • Page 32 Chapter 2 Disassembly Process 5. Loosen the four screws and unplug three connectors to remove the light cut module. Light cut module 6. Loosen four standoffs (yellow) and separate the lamp driver 1 from four spacer supports (blue). Lamp driver 1 EK-800U 2-26...

  • Page 33: Remove The Optical Engine Module

    1. Loosen two screws to remove the thermal switch. 2. Remove five screws securing the fan 8 module and duct blower module. 3. Remove three screws to separate the fan 8 and fan duct. Fan 8 Fan duct EK-800U 2-27...
  • Page 34 4. Remove five screws securing the fan 5 module and fan duct blower module. Fan duct blower 5. Remove three screws to separate the fan 5 and bracket. Fan 5 6. Remove six screws securing the fan 6 module. EK-800U 2-28...
  • Page 35 Chapter 2 Disassembly Process 7. Remove three screws to separate the fan 6 and bracket. Fan 6 8. Loosen eight screws to remove the engine module. Engine module EK-800U 2-29...

  • Page 36: Remove The Da,Lamp Housing

    Chapter 2 Disassembly Process 2-16 Remove the DA,Lamp Housing 1. Remove three screws and two connectors securing the DA module. 2. Then remove two screws securing the DA. 3. Remove one screw securing the photo sensor board. Photo sensor board EK-800U 2-30...

  • Page 37: Remove The Dmd,Dmd Board

    Chapter 2 Disassembly Process 4. Remove four screws securing the lamp housing module. Lamp housing module 2-17 Remove the DMD,DMD Board 1. Remove four screws securing the thermal module. Note: Use a new thermal pad when assemble the heat sink. EK-800U 2-31...
  • Page 38 3. Take out the DMD module then separate the DMD from DMD bracket. 4. Take out the DMD mask then loosen four screws to remove the thermal module. Note: Use a new thermal pad when assemble the heat sink. EK-800U 2-32...

  • Page 39: Remove The Color Wheel Docking Board

    Chapter 2 Disassembly Process 2-18 Remove the Color Wheel Docking Board 1. Remove two screws and unplug one connector securing the color wheel docking board. Color wheel docking board 2. The Optical engine module. Optical engine module EK-800U 2-33...

  • Page 40: Remove The Ac Inlet

    2-19 Remove the AC Inlet 1. Loosen six screws and take out the cable from wire mount then remove the bracket. 2. Separate the cable and fuse holder. Fuse holder 3. Separate the bracket and AC inlet. AC inlet EK-800U 2-34...

  • Page 41: Remove The Power Supply

    Chapter 2 Disassembly Process 2-20 Remove the Power Supply 1. Remove nine screws securing the power supply. 2. Unplug four connectors (red) securing the power supply. Power supply 3. Remove two cables. EK-800U 2-35...

  • Page 42: Remove The Fan 7 And Fan

    2-21 Remove the Fan 7 and Fan 10 1. Remove five screws securing the duct blower module and fan10. Fan 10 2. Remove six screws and one extend wire securing the duct blower module and fan 7. Fan 7 EK-800U 2-36...

  • Page 43: Remove The Bottom Cover

    Chapter 2 Disassembly Process 2-22 Remove the bottom cover 1. Remove the foot through the bottom of the projector. 2. Loosen ninteen screws to remove base shielding. EK-800U 2-37...

  • Page 44: Repair Action

    Board Board Wheel ware Board Firmware Version Update Color Wheel Index calibration Reset Lamp Hour Factory Reset Calibration Calibration Adjustment Focus Adjustment Re-write Serial Number Lens Calibration ADC calibration G Sensor Calibration Network Test HDBase T Function Test EK-800U 2-38...

  • Page 45: Chapter 3 Troubleshooting

    Solid Red – Over temperature Status Flashing Red – Fan failure Off – Picture mute is off and Shutter is open – image is displayed Shutter Flashing Green – Picture mute is on and Shutter is closed – image is black EK-800U...

  • Page 46: Equipment Needed

    Chapter 3 Troubleshooting 3-2 Equipment Needed 1. Projector 2. PC (Personal computer) 3. DVD player 4. Screw drivers 5. VGA cable, power cord, component cable, audio cable,HDMI cable 6. Voltage test meter EK-800U...

  • Page 47: Main Procedure

    Does the lamp B. power ignite? Troubleshooting C. PIN protect Is PIN protect Troubleshooting D. Image Is Image OK? Performance Troubleshooting E. Remote Is Remote Control Control OK? Troubleshooting F. Network Is network OK? Troubleshooting No Fault Found EK-800U...

  • Page 48: No Power Troubleshooting

    Pin 1 Voltage Pin 20 Use the voltage test meter to test the voltage of J2 of Main Board Pin 1, 13,15=5V? Change Power supply Change Main Board/Keypad Board Continue function test and other troubleshooting once power button backlight lit EK-800U...

  • Page 52: Pin Protect Troubleshooting

    PIN protect on? Show Enter PIN dialog Turn off the unit ,then hold Show Wrong power Button And press PIN correct? PIN message Enter button immediately. PIN will be reset to default .(Default PIN:Sequentially press these keys:1.2.3.4.5) Normal operation EK-800U...

  • Page 59: Chapter 4 Test & Inspection

    - CL-200 - Quantum Data 802B or CHROMA 2327 (Color Video Signal & Pattern Generator) 4-2 Service Mode and Factory Mode - EK-800U contains 2 kinds of mode 1. Service Mode (1) Turn on the projector (2) Press "Menu" button on Remote Controller or Keypad, choose "OPTION"...
  • Page 60 "LEFT +DOWN+RIGHT+UP" by keypad to access service mode. (5) Enter "OK" to get into service mode. 2. Factory Mode (1) Turn on the projector (2) Press "Exit->Right->Right->Right" buttons sequentically on remote control or keypad to get into factory mode. EK-800U...

  • Page 61: Factory Reset

    OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting: (1) Please press "Menu" button. (2) Get into service mode (refer to 4-2) (3) To execute "Factory Reset" function. EK-800U...

  • Page 62: Calibration

    - Connect PC and projector by RS232 cable then AC on. - Double click the “Factory mode tool” on PC then click “NVRam Reset All” to excute G-sensor calibration. - Wait for a while until the lamp light on, then the calibration is success. EK-800U...
  • Page 63 - Adjust the adjustment gear by hex socket, let the frequency of image shows agree with the table which corresponding brightness value. - After adjust it, tighten the screws on the side of gear (as yellow circle). EK-800U...
  • Page 64 - Press “Auto” key to execute the video calibration. Criteria - There should not have any lack of SMPTE BAR. Color levels should be sufficient and normal. - There is not any abnormal lines on the SMPTE BAR image. EK-800U...
  • Page 65 - Press "Auto" key to execute the PC calibration. Criteria - If there is noise on the screen, the product is Grays 16 considered as failure product. -The screen appears normal, it shouldn’t appear any abnormal condition, such as lines and so on. EK-800U...
  • Page 66 Shutter LED flashing yellow. - After several minutes, the projector will auto- power on, the fan calibration and auto waveform is finished. Note: If the Fan RPM does not meet the RPM range, change the corresponding Fan. (Fan5:3300~3700,Fan6:2500~2700,Fan7: 3300~3700,Fan8:3400~3700,Fan10:3400 ~3700) EK-800U...
  • Page 67 Note: If the brightness value is very far from 16, it may indicate that DA is not operating smoothly and needs to replaced. - Select DA. - Press Select, following Open > Close > Open to check whether DA is operating correctly. EK-800U...

  • Page 68: Adjustment

    - Refocus position 1 and see if position 2 is also in focus. If not, repeat step 1 to 3. - Adjust position 3 is the same method as position 2. - Repeat step till positions 1, 2 and 3 are in focus at the same time. EK-800U 4-10...

  • Page 69: Rod Adjustment

    - If the other color does not disappear, adjust the screw Z first, and then adjust the screw X and Y. Inspection item- Color saturation. Criteria - It should not have any abnormal color at the rim of the image by estimating through the eyes. EK-800U 4-11...
  • Page 70 It should be locked in the correct place. Plastic Parts All plastic parts can not be broken and damaged. Safety or warning All safety and warning labels should be visible, label including all contents. All interface connectors should be complete and Connector workable. EK-800U 4-12...

  • Page 71: Chapter 5 Firmware Upgrade

    5. Firmware Upgrade Note: Please always perform "Factory Reset" after all firmware has been upgraded. Section 1: Formatter/Scalar/LAN/MCU Firmware Upgrade 5-1-1 Equipment Needed Software: - EIKI B70 Upgrade Firmware Wizard 20151029.zip Hardware: - Projector - Power Cord - RJ45 cable(CAT-5e)
  • Page 72 Chapter 5 Firmware Upgrade 5-1-2 Firmware Upgrade Procedure 5-1-2-1 Windows Setting 1. Close Windows firewall. 2. Set HDD sleep timer larger than two hours. 3. Run as administrator in case of Windows 7 system. EK-800U...
  • Page 73 5-1-2-2 Installation of the Firmware Upgrade Utility 1. Download the latest firmware program file from the website, Unzip the file to the desktop and open the folder created. 2. Execute the Upgrade_Wizard.exe. 3. Update Details: - Compatible projector(s): WUXGA EK-800U...
  • Page 74 - Connect the RJ-45 cable to the projector and the computer. - Set the IP address of the computer to match the first three numbers of the projector. (for projector 192.168.000.100, set computer to 192.168.000.xxx where xxx is not 100) - Click "Next" to continue. EK-800U...
  • Page 75 - Do not start or exit any programs on the computer. - Do not turn off the projector or computer. - Do not connect or disconnect any cables or power cords. - Click "Next" to continue. 8. Choose upgrade items, then click next EK-800U...
  • Page 76 - This may take an hour, please wait. 10. Upgrade Scalar – PW392 - Installing firmware to projector. - This may take half an hour, please wait. 11. Upgrade LAN – PW808 - Installing firmware to projector. - This may take ten minutes, please wait. EK-800U...
  • Page 77 - This may take five minutes,please wait. 13. Checking in progress - After upgrading firmware procedure - Reboot to check firmware procedure - Send command to upgrade M8535 (optional) - Step 1 : Wait LAN ready - Step 2 : Wait the projector start up EK-800U...
  • Page 78 Chapter 5 Firmware Upgrade - Step 3 : Query FW version - Step 4 : Upgrade M8535 - Step 5 : Recheck projector reversion EK-800U...
  • Page 79 Chapter 5 Firmware Upgrade 14. Updating result - When firmware upgrade completes, will shows "Update Successful". V00.83 V00.83 A00.27 A00.27 F05.29 F05.29 G00.56 G00.56 15. Enter into factory mode to check Formatter/Scalar/ LAN/MCU firmware version. EK-800U...

  • Page 80: Recovery Mode

    Unzip the file and keep on your desktop. - Double click the folder. - Choose the upgrade file based on the system of - 64-bit system execute FlashUpgrader_x64.exe - 32-bit system execute FlashUpgrader_x32.exe - Unzip the file. EK-800U 5-10...
  • Page 81 Chapter 5 Firmware Upgrade 3. Choose "FlashUpgrader.exe" Program. - Double click "FlashUpgrader.exe" to execute FlashUpgrader setup. 4. Choose “USB 2.0”,then click “Flash” button to start FW upgrade. 5. Then will show upgrade progress bar. EK-800U 5-11...
  • Page 82 7. When appear " Programming completed", PW808 firmware upgrade procedure is finished. Note: - The lamp will not operate. - After upgrade finished, remove the power code. EK-800U 5-12...
  • Page 83 5. Connect the projector to AC and power it on. 6. When the source message is displayed on the bottom left of the projected image, click Next. 7. Choose upgrade items, then click next 8. Updating result - When firmware recovery completes, will shows "Update Successful". EK-800U 5-13...

  • Page 84: Re-Write Serial Number

    Chapter 5 Firmware Upgrade Section 3: Re-write Serial Number 5-3-1 Equipment Needed Software: - EIKI B70 HPBU TesterTool.zip Hardware: - Projector - Power Cord - "Cross over" female-female RS232 cable - PC or Laptop EK-800U 5-14...
  • Page 85 - Plug in the power cord. - Connect projector and PC by RS232 cable. 2. Please download the EIKI B70 HPBU TesterTool.zip from website, then double click the file. 3. Execute the "HPBU_Common Tester.exe". Note:Please ensure that the projector and PC baud rate is"19200".
  • Page 86 Chapter 5 Firmware Upgrade Then key in the Serial Number, for example "E58A1005". Then click "RUN" to re-write SN. Then the "Pass" message will be shown on the window. 6. Check Serial number. - press "MENU->OPTION". - check the serial number. EK-800U 5-16...
  • Page 87 51.78917G001 COVER REAR FAN B70 49.8RR01G001 DELTA AFB1212ME 120X120X38mm AXIAL FAN,WIRE LENGTH 350mm 51.78916G001 COVER REAR B70 75.78903G002 ASSY COVER TOP EIKI B70 80.78911G001 PCBA NEW PCBA PW808 MEDIA BOARD FOR B70 EK-800U PROJECTOR 51.78912G001 COVER RIGHT B70 70.78913GR01 ASSY FRONT COVER MODULE FOR 789 (SERVICE) 49.8RR01G001...
  • Page 88 Appendix A (Exploded Image) ASSY FRONT COVER MODULE RSPL Item Description Item # ASSY FRONT COVER MODULE FOR 789 (SERV- 70.78913GR01 ICE) CABLE W.A. 2PIN 520/35mm FILTER SWITCH 42.004D8G001 (LEFT / FRONT COVER) A70 EK-800U...
  • Page 89 Appendix A (Exploded Image) ASSY LEFT COVER MODULE RSPL Item Description Item # 51.78908G001 COVER LEFT B70 CABLE W.A. 2PIN 520/35mm FILTER SWITCH 42.004D8G001 (LEFT / FRONT COVER) A70 EK-800U...
  • Page 90 ASSY RIGHT COVER MODULE RSPL Item Description Item # 70.78916GR01 ASSY IO COVER MODULE FOR 789 (SERVICE) 51.78912G001 COVER RIGHT B70 51.78915G001 KEYPAD PLASTIC EIKI B70 51.78914G001 COVER RIGHT KEYPAD B70 80.78908G001 PCBA KEYPAD BOARD FOR B70 EK-800U PRO- JECTOR EK-800U...
  • Page 91 Appendix A (Exploded Image) ASSY BOTTOM COVER MODULE RSPL Item Description Item # 51.78911G001 COVER BOTTOM CW DOOR B70 51.78910G001 COVER BOTTOM B70 51.8RR27G003 FOOT ELEVATOR FOOT HOLDER LN2520A A70 52.78902G001 RUBBER ELEVATOR FOOT B70 70.72407GR01 ASSY BLOWER/70X70X25MM MODULE FOR 724 (SERVICE) EK-800U...
  • Page 92 Appendix A (Exploded Image) ASSY MAIN BOARD MODULE RSPL Item Description Item # 80.78911G001 PCBA PW808 MEDIA BOARD FOR B70 EK-800U PROJECTOR 70.78916GR01 ASSY IO COVER MODULE FOR 789 (SERVICE) 70.78911GR01 ASSY SCALAR BOARD MODULE FOR 789 (SERVICE) 70.78912GR01 ASSY FORMAT BOARD MODULE FOR 789...
  • Page 93 Appendix A (Exploded Image) ASSY TOP COVER MODULE RSPL Item Description Item # 75.78903G002 ASSY COVER TOP EIKI B70 EK-800U...
  • Page 94 80.8RRU2G001 PCBA FAN DOCKING BOARD FOR D11WU-H PROJECTOR 80.789W2G001 PCBA REAR LED BOARD FOR B70-WU PROJEC- 42.004FFG001 CABLE W.A. 4PIN 190mm LAMP COVER TO LVPS(INSIDE) A70 49.8RR01G001 DELTA AFB1212ME 120X120X38mm AXIAL FAN,WIRE LENGTH 350mm 19.00013G001 MISC FIZ FUSEHOLDER 5x20mm IP 40 0031.2207 SCHURTER EK-800U VIII...
  • Page 95 Appendix A (Exploded Image) ASSY FAN 6 MODULE RSPL Item Description Item # 70.72407GR01 ASSY BLOWER/70X70X25MM MODULE FOR 724 (SERVICE) EK-800U...
  • Page 96 Appendix A (Exploded Image) ASSY FAN 5 MODULE RSPL Item Description Item # 70.72407GR01 ASSY BLOWER/70X70X25MM MODULE FOR 724 (SERVICE) EK-800U...
  • Page 97 Appendix A (Exploded Image) ASSY FAN 8 MODULE RSPL Item Description Item # 70.72407GR01 ASSY BLOWER/70X70X25MM MODULE FOR 724 (SERVICE) EK-800U...
  • Page 98 ASSY COLOR WHEEL MODULE FOR 789 (SERV- 70.78917GR01 ICE) ASSY LIGHT ENGINE MODULE FOR 789 (SERV- 70.78914GR01 ICE) DMD 1920*1200 PIXEL 0.96” WUXGA 2xLVDS 48.8AYDMGD02 TYPE-A 75.8RR08G001 DA MODULE A70, 72MM THERMAL PAD PHASE CHANGE 52.8RR04G001 MATERIAL,21mmX14mmX0.2mm, K=3.3 PSX, EA- EK-800U...
  • Page 99 Appendix A (Exploded Image) RSPL Item Description Item # 55.8RR01G012 CARTON OUTSIDE EK-800U B70 56.78901G001 CUSHION EPE BOTTOM EK-800U B70 56.78902G001 CUSHION EPE TOP EK-800U B70 SP.78902GC01 Option Remote Control 51.8YS38G001 PE BAG 1000*730*0.1 MM 56.8CG01G001 EPE BAG FOR SHASTA 55.8PV02G001...

Table of Contents