Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Related Manuals for Eiki EK-620U
Summary of Contents for Eiki EK-620U
- Page 1 Warping and Blending Manual AP Applicable models EK-620U,621W,625U EK-800U,810U,811W,815U,820U Oct., 2019...
-
Page 2: Table Of Contents
Contents Preparation 1. Connection - - - - - 3 2. Projector - - - - - - - 4 3. PC (Laptop) - - - - - 5,6 Operation ・How to connect - - -7,8 ・Save / Open - - -- - -9 ・General - - - - - - - - 10 ・Warp - - - - - - - - - - 11,12 ・Edge Blending - - - -13,14... -
Page 3: Preparation
Preparation 1. Connection Connect an RJ45 cable to Ethernet port on the projector and the PC (Laptop). <Direct connection> <Multi connections> LAN Port 102... -
Page 4: Projector
2-1. Projector OSD menu : SETUP >Communications> LAN DHCP : OFF (direct connection) / ON (Multi connections) IP Address : Subnet Mask : Default Gateway : Do not need to change. <NOTE> When a DHCP server exists in the connected network, it assigns an IP address to the projector and the computer automatically. -
Page 5: Pc (Laptop)
3-1. PC (Laptop) Start > Control Panel > Network and Internet 3-2. Right-click on Local Area Connection, and select 【Properties 】. - Page 6 3-3. In the Properties window, select the Networking tab, and select 【 Internet Protocol Version 4 (TCP/IPv4 ) 】. 3-4. Select 【 Properties 】. 3-5. Select and following the projector IP address. Change the any numbers from Projector’s LAN information. Same as Projector’s LAN information...
-
Page 7: Operation
Operation This AP provides three major functions including 【 Warp 】 【 Edge Blending 】 and 【Black Level 】. ・Old version AP needs to be removed before install the new one. ・This function makes user be able to operate a single projector. Connecting Setting 1: Select 【File】→【New Multi-Function】. - Page 8 3： Input IP Address and press [Connect]. 4： Connection is successful, icon will be changed from Delete Connecting projector 1： Select Icon 2： [Edit][Delete] 3： Disappear the selected Icon...
-
Page 9: Save / Open
Save / Open Open 1: Select [File][Open] 2: Select directory and file. 3: Edit IP address and connect to the projector. 4: Click [Reconfigure]to load the settings. Save 1: Select [File][Save] 2: Select directory and edit the file name. <NOTE> [Configure] button is not available after selected【... -
Page 10: General
【 General 】 Projector Output Resolution (Default: WUXGA) ・Select the native resolution of the projector. Connect Setting (Default: 192.168.0.100) ・Connect to the shown IP address. Function Settings ・Reset All: Reset all settings to default value. This function is not available after pressed the 【 Warp 】 【 Edge Blending 】 or 【Black Level 】. -
Page 11: Warp
【 Warp 】 Move Pitch (Default: 100) ・Set the amount of movement at a time ・Adjust the range of moving pitch by mouse or using 【+】and【-】on the keyboard. Grid Number (Default: 3x3) ・Set the Warp's grid number ・Adjust the grid number by mouse or using 【Ctrl】and【+】, 【Ctrl】and【-】on the keyboard. -
Page 12: Warp
Test Pattern ・Show the grid pattern on the projection screen. ・ Color: Can be select the color Red or Green. Example of adjustment with test pattern ・Use test pattern to speed up the warping/blending process as shown below. Reset ・Reset all the setting value for only warp function. -
Page 13: Edge Blending
【 Edge Blending 】 Default setting value on each resolution 【WUXGA (1920 x 1200)】 Default Value Bottom Left Right Start 1100 1820 Width 【WXGA (1280 x 800)】 Default Value Bottom Left Right Start 1180 Width ・ Check “Enable Marker” and appear the blending line on the screen. Marker “Start”... -
Page 14: Edge Blending
Enable Marker ・ Marker can help to align the over-lapped area. ・ Set the start position and corresponding width to speed up the blending process as shown below. Gamma (Operating range : 1.0 – 3.0 Default: 2.2) ・ Change the gamma curve of the blending area. ・... -
Page 15: Black Level
【 Black Level 】 This function is only for adjusting non over-lapped area when whole image is dark. <Example of adjustment black level> Grab 4 points on black level tab to match the non over-lapped area and start to adjust the brightness of black level. Click the palette row to edit colors dialog for color settings. - Page 16 Green Cyan Yellow ・ Black level function only supports quadrangle shape and there are four points to determine the quadrangle shape. ・ Select the control point, use mouse or [W,A,S,D] on the keyboard. ・ Selected the control point is changed to hollow. ・...
- Page 17 Transparent (Operating range : 1.0 – 3.0 Default: 2.2) This function only available when projecting color images after black level adjustment. With this “Transparent” function will make the over-lapped area of the image appearing brighter. When the projection image is not black, over-lapped area won't see brighter.