Table of Contents
Advertisement
b
Leeding and fiLLing brake
EBT (Easy Bleed Technology) makes it easy to bleed the brake.
L
The only difference between bleeding and filling – if any – is the
L
amount of oil required – the procedure is identical.
Always fill at the brake calliper, never at the brake lever!
L
Loss of oil and irreparable damage to the braking system.
Open the screw plugs for bleeding and filling only.
Use MAGURA Royal Blood (mineral oil) exclusively for bleeding
and filling – never DOT brake fluid.
Because MAGURA Royal Blood does not age, it is not necessary to
L
bleed or refill your MAGURA brake regularly. Do this only if one of
the following reasons requires it:
The brake does not respond immediately when the brake lever is
Ö
actuated.
Pressure point is not clearly defined, it is spongy or does not
Ö
remain constant.
After changing the brake hose.
Ö
To bleed or fill your MAGURA brake you will need the MAGURA
L
Service Kit or the MAGURA Pro Bleed Kit – available from dealers.
Insert barbed fitting
tightly into the filling line by hand
1
)
(
)
Fill filling syringe
with MAGURA Royal Blood.
2
(
)
)
Make sure that there is no air in the filling syringe and filling line.
)
Pull the piston of the bleeding syringe
)
Piston base is above bleed bore
Ö
If your bleeding syringe does not have the bleed bore, you can
L
make it yourself – the easiest way is to use a Ø 2 mm drill bit for
wood or metal.
24
maintenanCe
[
].
h1
out as far as the stop.
3
(
)
.
4
(
)
At the right brake lever: clockwise in "Plus" (+) direction.
L
At the left brake lever: counterclockwise in "Plus" (+) direction.
Rotate rotating dial (BAT)
1
(
)
[
].
C1
Remove the wheel.
)
Carefully press brake pads apart to the stop with transport device
)
or a wide screwdriver.
All brake pistons
are in fully extended position
1
Ö
(
)
Removing brake pads – see
)
Screw in brake pad locking screw
)
Insert transport device
between the brake pistons from below
6
)
(
)
until it locks.
Use two transport devices per brake calliper with 4-piston brake
callipers and fasten them with a rubber ring or similar if neces-
sary!
Align brake caliper vertically.
)
If your assembly stand makes it impossible to align the brake
L
calliper vertically, you will have to unscrew it to bleed it. We always
recommend this procedure, because it is better to hold the brake
calliper above the level of the brake lever on completion of the
bleeding process and before removing the filling syringe to prevent
oil loss.
Unscrew the screw plug
7
(
)
)
Screw the barbed fitting of the filling syringe
)
and tighten with tightening torque of 4 N·m (35 lbf·in)
Loosen the bottom clamping screw
)
Turn the brake lever so it is pointing horizontally forwards or
)
backwards
[
].
h3
Tighten the bottom clamping screw
)
4 N·m (35 lbf·in).
Unscrew the EBT screw
8
)
(
)
to the stop in the "Plus" (+) direction
)
[
].
g2
, page 23.
c
hanging brake PadS
[
].
h2
5
(
)
from the filler hole of the brake calliper.
into the filler hole
2
(
)
[
h2
[
].
A3
3
(
)
with tightening torque of
from the bleed hole
[
].
h3
].
Hide quick links:
Advertisement
Table of Contents
