Advertisement
FX
-4AD-PT SPECIAL FUNCTION BLOCK
2N
This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX
-4AD-PT special function block and should be read and understood before
2N
attempting to install or use the unit.
Further information can be found in the FX PROGRAMMING MANUAL(ΙΙ) and FX
FX
/FX
SERIES HARDWARE MANUAL.
3U
3UC
Guidelines for the Safety of the User and Protection of the FX
special function block.
This manual should be used by trained and competent personnel. The definition of such a person or
persons is as follows:
a) Any engineer using the product associated with this manual, should be of a competent nature,
trained and qualified to the local and national standards. These engineers should be fully aware of
all aspects of safety with regards to automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and qualified to
the local and national standards.
c) All operators of the completed equipment should be trained to use this product in a safe and
coordinated manner in compliance to established safety practices.
Note: The term 'completed equipment' refers to a third party constructed device which contains or uses
the product associated with this manual.
Notes on the Symbols Used in this Manual
At various times throughout this manual certain symbols will be used to highlight points of information
which are intended to ensure the users personal safety and protect the integrity of equipment.
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
•
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage
that may arise as a result of the installation or use of this equipment.
•
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for the actual use of
the product based on these illustrative examples.
•
Owing to the very great variety in possible applications for this equipment, you must satisfy yourself as
to its suitability for your specific application.
1. INTRODUCTION
•
The FX
-4AD-PT analog block amplifies the input from four platinum temperature sensors (Pt 100, 3
2N
wire, 100 Ω) and converts the data into 12 bit reading's stored in the main unit. Both Centigrade (°C)
and Fahrenheit (°F) can be read. Reading resolution is 0.2°C to 0.3°C / 0.36°F to 0.54°F.
•
The FX
-4AD-PT can connected to the FX
/FX
/FX
/FX
2N
0N
1N
2N
Controllers (PLC).
•
All data transfers and parameter setups are adjusted via software control of the FX
of the TO/FROM applied instructions in the PLC.
•
The FX
-4AD-PT occupies 8 I/O points on the PLC expansion bus. The 8 I/O points can be allocated
2N
from either inputs or outputs. The FX
-4AD-PT draws 30mA from the 5V rail of the main unit or
2N
powered extension unit.
2. EXTERNAL DIMENSIONS
USER'S GUIDE
JY992D65601E
DIN rail
mounting slot
35 (1.38)
/FX
/FX
/FX
/
0N
1N
2N
2NC
-4AD-PT
2N
3. CONNECTION WITH PLC
3.1 Connection with PLC
The FX
-4AD-PT unit can be connected to the PLCs as follows. Restrictions apply to the maximum
2N
number of connectable units, depending on the DC24V/DC5V Power Supply capacities and the Main Unit/
Special Function Unit types. For details, refer to the respective PLC manual.
FX
/FX
: The maximum connectable units is 8.
2N
3U
*1
FX
: The maximum connectable units is 8.
3UC
To connect the FX
required.
FX
: The maximum connectable units is 4.
2NC
To connect the FX
FX
: The maximum connectable units is 8.
1N
FX
: The maximum connectable units is 4.
0N
*1 Up to 7 units can be connected to an FX
3.2 Special function block numbers
Other special units of blocks that use FROM/TO instructions, such as analog input blocks, analog output
blocks and high-speed counter blocks, can be directly connected to the main unit of the PLC or to the right
side of other extension blocks or units.
COM
X0
X2
L
N
24+
X1
FX
-48MR-ES/UL
2N
Y0
Y2
Y4
Y6
COM1
Y3
COM2
Y5
Y7
FX
-48MR-ES/UL
2N
X000-X027
Y000-Y027
4. WIRING
4.1 Wiring
Pt100
1
shielded CH1
/FX
/FX
series Programmable
2NC
3U
3UC
-4AD-PT; by use
2N
Pt100
1
shielded
DC24V±10% 50mA 2
4
3
D grounding
PLC
(100
or less)
Extension cable
Weight: Approx. 0.3 kg (0.66 lbs)
Dimensions: mm (inches)
87 (3.43)
55 (2.17)
Mounting holes
4 (0.16)
4.5 (0.18) dia.
POWER
24V
LED
24V
A/D
A/D
LED
Extension cable
9 (0.35)
4 (0.16)
Terminal screws M3 (0.12)
and connector
-4AD with the FX
main unit, FX
-CNV-IF or FX
2N
3UC
2NC
-4AD-PT with the FX
main unit, FX
-CNV-IF is required.
2N
2NC
2NC
-32MT-LT PLC.
3UC
IN 0
1
2
3
4
5
6
7
X4
X6
X10
X14
X16
X20
X22
X24
COM
X0
X2
X4
X6
X5
X7
X13
X15
X17
X21
X23
X25
L
N
24+
X1
X3
X5
POWER
POWER
POWER
0
1
2
3
4 5 6
7
20
21
22 23 24 25 26
27
IN
10
11
12 13
14
15
16
17
POWER
T.V
PROG.E
6
7
20
21
22 23 24 25 26
27
CPU.E
FX -4AD
FX
-16EX
FX -4DA
16 17
2N
2N
2N
Y10
Y14
Y20
Y22
Y24
Y26
COM5
IN 0
Y0
Y2
Y4
Y6
Y10
COM3
Y13
COM4
Y15
Y21
Y23
Y25
Y27
COM1
Y1
Y3
COM2
Y5
Y7
COM3
1
2
3
24V
4
24V
5
6
A/D
D/A
7
FX
-4AD
FX
-16EX
FX
-4DA
FX
2N
-32ER
2N
2N
2N
X030
Special block
X050-X067
Special block
-X047
No.1
Y030-Y047
No.0
5V
The cable of the Pt 100 sensor or a twisted shielded
4.7K
4.7K
cable should be used for the analog input cable. This
L+
100K
analog input cable should be wired separately from
L-
100K
I-
power lines or any other lines which may induce noise.
AG
FG
The three wire method improves the accuracy of the
sensors by compensating voltage drops.
CH4
If there is electrical noise, connect the FG (frame
L+
L-
ground) terminal with the ground terminal. (In CH1,
5V
I-
there is no FG terminal. Use FG terminal of other
FG
AG
channels.)
24+
+15V
DC/DC
AG
Connect the ground terminal on the FX
converter
24-
-15V
with the grounded terminal on the main unit. Use
grounding on the main unit, if grounding is possible.
FX
-4AD-PT
2N
Either an external or the 24V built-in supply in the PLC
may be used.
For additional data regarding EMC considerations
please see section 10.
4.2 Using crimp terminations
• Use crimp terminals as indicated on the left.
less than
6.2mm (0.24)
• Secure the terminal using a tightening torque of between 0.5 and 0.8
Use M3 (0.12)
55 (2.17)
• Wire only to the module terminals discussed in this manual. Leave all
less than
6.2mm (0.24)
5. INSTALLATION NOTES AND USAGE
5.1 General specification
Item
General specifications
Dielectric withstand voltage
5.2 Power supply specification
Item
Analog circuits
Digital circuits
5.3 Performance specification
Analog Inputs
Item
Both °C and °F are available by reading the appropriate buffer memory (BFM).
-1PS-5V is
3UC
Platinum Temperature Pt 100 sensors (100 Ω), 3-wire, 4-channel (CH1, CH2,
Analog input signal
CH3, CH4), (DIN 43760, JIS C 1604-1997, JIS C 1604-1981)
1 mA. sensor: 100 Ω Pt 100
Current to sensor
Compensated range
-100°C to +600°C
-1000 to 6000
Digital output
12-bit conversion 11 data bits +1 sign bit
Minimum resolvable
0.2°C to 0.3°C
temp.
± 1% full scale (compensated range)
Overall accuracy
See section 7.0 for special EMC considerations
Conversion speed
60ms (15 ms for 4 channels)
Analog Inputs continued...
X10
X12
X14
X16
X7
X11
X13
X15
X17
IN
POWER
0
1
2
3
4
5
6
7
10
11
12 13
14
15
16
17
POWER
OUT
0
1
2
3
4
5
6
7
+6,000
10
11
12 13
14
15
16
17
Y12
Y14
Y16
Y11
Y13
COM4
Y15
Y17
24V
A/D
Conversion
Characteristics
-100°C
FX
-4AD-PT
2N
Special block
No.2
Miscellaneous
Item
Isolation
Number of occupied I/O points
-4AD-PT unit
2N
⋅
N
m.
others vacant.
Specification
Same as those for the main unit
500V AC, 1min (between all terminals and ground)
Specification
24V DC ± 10%, 50mA
5V DC, 30mA (internal power supply from the main unit)
Centigrade
Fahrenheit
-148°F to +1112°F
-1480 to +11120
16-bit binary with sign
0.36°F to 0.54°F
+11,120
Digital
Digital
output
output
-148°F
-1,000
+600°C
-1,480
+1,112°F
Temp. input°F
Temp. input°C
Specification
Photo-coupler isolation between analog and digital circuits.
DC/DC converter isolation of power from the main unit.
No isolation between analog channels.
The block occupies 8 I/O points
(can be either inputs or outputs)
Advertisement
