Advertisement
ADJUSTMENTS
1
Area angle adjustment
1-1.Area depth angle adjustment
When adjusting the 2nd row close to the door,
see dipswitch 16 in Dipswitch settings table and REFERENCE for
the easier adjustment.
Shallow
-8°
+8°
Make sure that the detection area does not overlap with the door / header, and there is no highly
NOTE
reflecting object near the detection area otherwise ghosting / signal saturation may occur.
1-2.Area width angle adjustment
The angle of the detection area
can both be moved 7° either left or right in 2 steps.
3.5°×2
3.5°×2
Left
2
Area width adjustment
Adjust the detection area width with
the adjustment screws.
eliminated
NOTE
When setting the detection area width,
make sure to turn the adjustment screws until it clicks.
cannot be eliminated separately, neither can
1 2
3
FLEX EYE angle adjustment
Make sure to adjust the FLEX EYE angle depending on the door type and the intended touchless plate position
otherwise the sensor may not detect when a hand is approached.
3-1.FLEX EYE width angle adjustment
Left
Right
6°×7
6°×7
3-2.FLEX EYE depth angle adjustment
Shallow
Deep
-14°
+2°
NOTE
After adjusting the angle, make sure that the FLEX EYE is placed on the proper position for your use.
Affix the touchless plate on the appropriate position after adjusting the FLEX EYE.
Make sure to affix the touchless plate where a hand
CAUTION
is not caught by the door during door opening and closing.
Risk of getting caught.
4
Dipswitch settings
After changing the dipswitch settings,
make sure to push the function switch for 2 seconds.
Dipswitch settings table
Function
Low
High
Dipswitch
Sensitivity
1
1
Dipswitch
30sec.
60sec.
2
Presence timer
Dipswitch
2
3
2
3
Dipswitch
A
B
4
Frequency
Dipswitch
5
4
5
4
6rows
5rows
Dipswitch
6
Row adjustment
Dipswitch
7
6 7
6 7
OFF
ON
Dipswitch
Immunity
8
8
N.O.
N.C.
Dipswitch
Activation output
9
9
Enable
Disable
Dipswitch
Self Monitoring
10
10
10
High
Low
Dipswitch
Safety output
11
11
11
High
Low
Dipswitch
Safety input
12
12
12
Low
High
FLEX EYE
Dipswitch
13
Sensitivity
13
13
ON
OFF
FLEX EYE
Dipswitch
14
mode
14
14
OFF
ON
BLUEZONE
Dipswitch
15
(1st row)
15
15
OFF
ON
Dipswitch
Installation mode
16
16
16
Deep Shallow
[m(feet,inch)]
Deep
2.0(6 ' 7 " )
2.0(6 ' 7 " )
2.5(8 ' 2 " )
2.5(8 ' 2 " )
3.0
2.0
1.0
0
(9 ' 10 " )
(6 ' 7 " )
(3 ' 3 " )
Left
[m(feet,inch)]
2.0(6 ' 7 " )
2.0(6 ' 7 " )
2.5(8 ' 2 " )
2.5(8 ' 2 " )
2.0
1.0
0
1.0
Right
(6 ' 7 " )
(3 ' 3 " )
(3 ' 3 " )
1
2
7
8
Left
Right
eliminated
2.0(6 ' 7 " )
2.5(8 ' 2 " )
2.0
(6 ' 7 " )
1
7 8
Double slide door
Single slide door
[m(feet,inch)]
0.08
(3")
Operation
indicator :
Purple
push 2 seconds
Setting
Comment
Set the detection area sensitivity according to
the mounting height.
1
The presence timer is applied to
180sec.
600sec.
BLUEZONE(1st row), 2nd row and 3rd row.
The presence timer can be selected
3
2
3
2
3
from 4 settings.
C
D
When using more than one sensor close
to each other, set the frequency different
for each sensor.
5
4
5
4
5
4rows
3rows
Set the depth rows with dipswitches 6 and 7.
6 7
6 7
Set dipswitch 8 to "ON" when the sensor
operates by itself (Ghosting).
8
Dipswitch 9 is for the Activation output
to door controller.
9
When the door remains open and the
operation indicator shows Fast/Slow Green
Blinking, refer to TROUBLESHOOTING.
If the door still remains open, set dipswitch 10
to "Disable".To comply with EN 16005, set
dipswitch 10 to "Enable".
Dipswitch 11 is for the Safety output
(to door controller).
Dipswitch 12 is for the Safety input
(from door controller).
Adjust sensitivity for FLEX EYE.
Select the FLEX EYE mode "ON" or "OFF".
ON : Activation output is emitted when a
detection occurs in FLEX EYE and the
2nd to 4th row.
OFF : Activation output is emitted when a
detection occurs in the 2nd to 6th row.
When dipswitch 15 is set to "ON", the
BLUEZONE (1st row) is active and looks
through the threshold.
Set dipswitch 16 to
"ON"
row. During the installation mode only the
2nd row remains active and the operation
indicator shows yellow. After setting the row
switch dipswitch 16 "OFF".
CHECKING
Check the operation according to the chart below.
Entry
[m(feet,inch)]
Image
Operation
indicator
9
2.0
1.0
0
-1.0
Activation
(6 ' 7 " )
(3 ' 3 " )
(3 ' 3 " )
output (
*1
)
9
11
Safety
output
11
Right
[m(feet,inch)]
Entry
Image
1.0
0
1.0
2.0
(3 ' 3 " )
(3 ' 3 " )
(6 ' 7 " )
Operation
Front view
indicator
[m(feet,inch)]
9
Activation
*1
output (
)
9
11
Safety
output
11
1.0
0
1.0
2.0
(3 ' 3 " )
(3 ' 3 " )
(6 ' 7 " )
2
3 4 5
6
7
8
NOTE
*1
:
*2
:
INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS
WARNING
1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth.(Do not use any cleaner / solvent.)
2. Do not wash the sensor with water.
3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.
[m(feet,inch)]
4. When the operation indicator blinks Green, contact your installer or service engineer.
0.08
5. Always contact your installer or service engineer when changing the settings.
(3")
6. Do not paint the detection window.
1. When turning the power ON, always walk-test the detection area to ensure the proper operation.
NOTE
2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)
TROUBLESHOOTING
Door operation
Door does not
open when a
person enters the
detection area and
FLEX EYE.
Door opens when
a person enters
the detection area.
Door opens when
no one is in the
detection area.
(Ghosting)
Door remains
open
Proper operation
* : After changing the dipswitch settings, make sure to push the function switch for 2 seconds.
REFERENCE
Area depth adjustment with INFRARED FINDER (Separately available)
1.Turn the depth angle adjustment screw to the right (Deep) to place the
detection area most away from the door.
2. Set INFRARED FINDER sensitivity to "H" (High) and place it on the floor as shown below.
3. Turn the depth angle adjustment screw to the left (Shallow) until the emitting area is placed at the position where
INFRARED FINDER is in the low detection status (Slow Red Blinking).
to adjust the 2nd
Manufacturer
OPTEX Co.,LTD.
5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: +81(0)77 579 8700
WEBSITE: www.optex.co.jp/as/eng/index.html
Outside of
Entry to
Power off
detection area
4th to 6th row
None
Green
Orange
N.O.
OFF
N.C.
High
ON
OFF
Low
OFF
Entry to
Entry to
Outside of
BLUEZONE
FLEX EYE
detection area
(
*2
)
only
Fast Purple
Blue
Green
Blinking
N.O.
OFF
N.C.
ON
High
OFF
ON
ON
Low
ON
OFF
OFF
Activation output shows the status of when FLEX EYE mode is enabled. (Dipswitch 14 is set to "ON".)
When dipswitch 15 is set to "ON".
Operation
Possible cause
indicator
None
Wrong power supply voltage.
Wrong wiring or connection failure.
Unstable Wrong detection area(2nd to 4th row) and
FLEX EYE positioning.
Sensitivity of detection area(2nd to 4th row) is
too low.
Sensitivity of FLEX EYE is too low.
Short presence timer.
Dirty detection window.
Proper
Wrong wiring or connection failure.
Proper
FLEX EYE function is not working.
(Dipswitch 15 is up side position)
Unstable
Objects that move or emit light in the
detection area.
The detection area overlaps with that of another
sensor.
Waterdrops on the detection window.
The detection area overlaps with the door/header. Adjust the detection area to "Deep"(Outside).
Sensitivity of detection area is too high.
Sensitivity of FLEX EYE is too high.
Others
Proper
Wrong setting of dipswitches.
Proper
Sudden change in the detection area.
Wrong wiring or connection failure.
Yellow
Installation mode is set to "ON".
Fast
Sensitivity of detection area is too low.
Green
Sensitivity of FLEX EYE is too low.
Blinking
Dirty detection window.
Sensor failure.
Slow
Signal saturation. (2nd and/or 3rd row)
Green
Blinking
The detection area overlaps with the door/header. Adjust the detection area to "Deep" (Outside).
Setting error.
Red &
Green
Blinking
Slow
Signal saturation.
Green
(4th, 5th, 6th row and/or BLUEZONE)
Blinking
Slow
Signal saturation. (FLEX EYE)
Purple
Blinking
FLEX EYE overlaps with the header.
Detection area
Detection area
European Subsidiary
OPTEX Technologies B.V.
Henricuskade 17, 2497 NB The Hague, The Netherlands
FAX.: +81(0)77 579 7030
TEL.: +31(0)70 419 41 00
E-MAIL: info@optex.eu
Entry to
Entry to
Entry to
FLEX EYE
and
3rd row
2nd row
2nd to 4th row
Red
Red Blinking
Purple
OFF
ON
ON
OFF
OFF
ON
Possible countermeasures
Set to the stated voltage.
Check the wires and connector.
Check ADJUSTMENT 1,2,3.(*)
Set the detection area sensitivity higher.
Set the FLEX EYE sensitivity higher.
Set the presence timer longer.
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Check the wires and connector.
Check ADJUSTMENT 4 dipswitch 14.(*)
Remove the objects.
Check ADJUSTMENT 4 dipswitch 4,5.(*)
Use the rain-cover (Separately available).
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Install in a place keeping the waterdrops off.
Set the detection area sensitivity lower.
Set the FLEX EYE sensitivity lower.
Set dipswitch 8 to "ON".(*)
Check ADJUSTMENT 4 dipswitch 9,11,12.(*)
Check ADJUSTMENT 4 dipswitch 1 to 3.(*)
If the problem still persists, hard-reset the
sensor.(Turn the power OFF and ON again.)
Check the wires and connector.
Set dipswitch 16 to "OFF".(*)
Set the detection area sensitivity higher.
Set the FLEX EYE sensitivity higher.
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Contact your installer or service engineer.
Remove highly reflecting objects from the
detection area. Lower the sensitivity.(*)
Change the area depth angle.
After changing the dipswitch settings, make
sure to push the function switch for 2 seconds.
Remove highly reflecting objects from the
detection area. Lower the sensitivity.(*)
Change the area depth angle.
Remove highly reflecting objects from the
FLEX EYE. Lower the FLEX EYE sensitivity.
Change the area depth angle for FLEX EYE.
Adjust FLEX EYE to "Deep" (Outside).
INFRARED FINDER
FAX.: +31(0)70 317 73 21
WEBSITE: www.optex.eu
Advertisement
