Optex OA-FLEX AIR T User Manual page 4

ADJUSTMENTS
1
Secondary Activation area angle adjustment
1-1.Secondary Activation area depth angle adjustment
When adjusting the 2nd row close to the door,
see Dipswtich settings table dipswitch16 for the easier adjustment.
Deep
-16° 0°
NOTE Make sure that the Secondary Activation area does not overlap with the door / header, and there is no highly
reflecting object near the detection area otherwise ghosting / signal saturation may occur.
REFERENCE
Area depth adjustment with INFRARED FINDER (Separately available)
1.Turn the depth angle adjustment screw to the right (Deep) to place the
Secondary Activation area most away from the door.
2. Set INFRARED FINDER sensitivity to "H" (High) and place it on the floor as shown below.
3. Turn the depth angle adjustment screw to the left (Shallow) until the emitting area is placed at the position where
INFRARED FINDER is in the low detection status (Slow Red Blinking).
1-2.Secondary Activation area width angle adjustment
The width of the activation Secondary Activation area
can both be moved at the same time 7° either left or right in 2 step.
Left
2
Secondary Activation area width elimination
To adjust the Secondary Activation area width,
use the adjustment screws.
NOTE
When setting the Secondary Activation area width,
make sure to turn the adjustment screws until it clicks.
cannot be eliminated separately, neither can
1 2
3
FLEX EYE angle adjustment
Make sure to select the FLEX EYE angle depending on the door type and the intended touchless plate position
otherwise the sensor does not send an output when a hand is waved.
3-1.FLEX EYE width adjustment
Left Right
3-2.FLEX EYE Depth adjustment
Shallow Deep
-14° +2°
NOTE After adjust the angle, please check the FLEX EYE is on the best position for your use.
Please check the door will be open, when you are detected in the area between 2nd to 4th row.
Operation indicator color will be purple, when all the adjustment are OK.
3-3.Affix the touchless plate on the appropriate position after adjusting the FLEX EYE.
Make sure to affix the touchless plate where a head
CAUTION
is not caught by the door during door closing.
Risk of getting caught.
4
Dipswitch settings
Dipswitch settings table
Function
Dipswitch
Low Middle
Secondary
1
Activation area
Dipswitch 1 2 1
Sensitivity
2 6'7" to 8'2" 6'7" to 8'2"
Dipswitch
30sec. 60sec.
3
Presence timer
Dipswitch
3 4 3
4
Dipswitch
Setting1 Setting2
5
Frequency
Dipswitch
5 6 5
6
Normal Rain
Dipswitch
Rain mode
7
7
Normal Snow
Dipswitch
Snow mode
8
8
6rows 5rows
Dipswitch
9
Row adjustment
Dipswitch
10
9 10 9 10
OFF ON
BLUEZONE
Dipswitch
11
(1st row)
11
N.O. N.C.
Secondary
Dipswitch
12
Activation output
12
Dipswitch
Low Middle
13
FLEX EYE
Sensitivity
Dipswitch
13 14 13
14
ON OFF
Dipswitch
FLEX EYE mode
15
15
OFF ON
Dipswitch
Installation mode
16
16
Deep
Shallow
[feet,inch(m)]
Shallow
6'7"
6'7"
(2.0)
(2.0)
9'10" 9'10"
(3.0) 9'10" (3.0) 6'7"
6'7" 3'3" 0
(3.0) (2.0) (1.0)
Secondary Activation area
INFRARED FINDER
Secondary Activation area
7° to Left
[feet,inch(m)]
6'7"
(2.0)
9'10"
(3.0) 6'7"
3'3" 0 3'3" 3'3"
Right
(2.0) (1.0) (1.0) (1.0)
1 2 7 8
Left Right
eliminated eliminated
6'7"
(2.0)
9'10"
(3.0)
6'7"
(2.0)
7 8
1
Double slide door Single slide door
[feet,inch(mm)]
Operation
indicator :
Purple
Setting
Comment
Set the sensitivity according to the
High S-High
mounting height. Values below dipswitch
are reference only.
2
1 2 1 2
7'7" to 8'10" 8'2" to 9'10"
All rows have the presence detection
180sec. 600sec.
function.
The presence timer can be selected from
4 3 4
3 4
4 settings.
When using more than one sensor close
Setting3 Setting4
to each other, set the frequency different
for each sensor.
6 5 6 5 6
Set this switch to Rain if the sensor is
used in a region with a lot of rain.
7
Set this switch to Snow if the sensor is
used in a region with snow or a lot of
8 insects.
4rows 3rows
Set the depth rows with dipswitches
9 and 10.
9 10 9 10
When dipswitch 11 is set to ON, the
BLUEZONE (1st row) is active and looks
through the threshold.
11
Select "N.O."/"N.C." for
Secondary Activation output.
12
Adjust sensitivity for "FLEX EYE"
High S-High
detection.
14 13 14 13 14
Select the FLEX EYE mode ON or OFF.
See FLEX EYE MODE.
15
Set dipswitch 16 to ON to adjust the 2nd
row. During the installation mode only the
2nd row remains active and the operation
indicator shows yellow. After setting the
16
row switch dipswitch 16 OFF.
CHECKING
Check the operation according to the chart below.
Entry
[feet,inch(m)]
Image
Operation
indicator
3'3" 0 3'3"
(2.0) (1.0) (1.0)
Primary Activation
output
Secondary 12
Activation
output
12
Entry
Image
Operation
indicator
7° to Right
[feet,inch(m)]
Primary Activation
output
6'7"
Secondary 12
(2.0)
Activation
9'10"
output 12
(3.0)
0 3'3" 6'7"
(1.0) (2.0)
NOTE No output is made when sensor detects an object in the BLUEZONE(1st row).
Front view
INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS
[feet,inch(m)]
WARNING
1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth.(Do not use any cleaner / solvent.)
2. Do not wash the sensor with water.
3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.
4. When the operation indicator blinks Green, contact your installer or service engineer.
5. Always contact your installer or service engineer when changing the settings.
3'3" 0 3'3" 6'7"
6. Do not paint the detection window.
(1.0) (1.0) (2.0)
2 3 4 5 6 7 8
1. When turning the power ON, always walk-test the detection area to ensure the proper operation.
NOTE
2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)
TROUBLESHOOTING
Operation
Door operation
indicator
[feet,inch(mm)]
Door does not
open when a
person enters
Unstable Wrong Secondary Activation area
the Secondary
Activation area.
Door opens Unstable
when no one
is in the
Secondary
Activation area.
(Ghosting)
Door remains
open
Blinking
Proper
operation
Blinking
Blinking
Access setting website from here.
Manufacturer
OPTEX Co.,LTD.
5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: +81(0)77-579-8700
FAX.: +81(0)77-579-7030
WEBSITE:
www.optex.co.jp/as/eng/index.html
Outside of Entry to
Power off
detection area 4th to 6th row
None Green Orange
OFF OFF
N.O. OFF
ON
ON
N.C.
Entry to
Entry to Outside of
FLEX EYE
BLUEZONE detection area
only
Blue Green Purple Blinking
OFF OFF OFF
ON
N.O. OFF OFF
OFF ON ON
N.C.
Possible cause
Wrong power supply voltage.
None
Wrong wiring or connection failure.
positioning.
Sensitivity of Secondary Activation area
is too low.
Sensitivity of FLEX EYE is too low.
Short presence timer.
Dirty detection window.
Proper Wrong wiring or connection failure.
FLEX EYE function is working.
(Dipswitch 15 is down side position)
Objects that move or emit light in the
Secondary Activation area.
The Secondary Activation area overlaps
with that of another sensor.
Waterdrops on the detection window.
The Secondary Activation area overlaps
with the door/header.
Sensitivity of Secondary Activation area
is too high.
Sensitivity of FLEX EYE is too high.
Proper Wrong setting of dipswitches.
Proper Sudden change in the
Secondary Activation area.
Wrong wiring or connection failure.
Yellow Installation mode is set to "ON".
Fast Sensitivity of Secondary Activation area
Green is too low.
Sensitivity of FLEX EYE is too low.
Dirty detection window.
Sensor failure.
Slow Signal saturation.
Green (Secondary Activation area)
Secondary Activation area overlaps
with the door/header.
Slow Signal saturation. (FLEX EYE)
Purple
FLEX EYE overlaps with the header.
North and South America Subsidiary
OPTEX INCORPORATED
18730 S. Wilmington Avenue, Suite 100
Rancho Dominguez CA 90220 U.S.A
TEL.: +1-800-877-6656
FAX.: +1(310)214-8655
WEBSITE: www.optextechnologies.com
Entry to
Entry to Entry to
FLEX EYE
and
3rd row 2nd row
2nd to 4th row
Red Red Blinking Purple
ON
OFF
ON
OFF
Possible countermeasures
Set to the stated voltage.
Check the wires and connector.
Check ADJUSTMENT 1.
Set the Secondary Activation area sensitivity higher.
Set the FLEX EYE sensitivity higher.
Set the presence timer longer.
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Check the wires and connector.
Check FLEX EYE MODE.
Remove the objects.
Check ADJUSTMENT 1.
Or change Frequency setting.
Use the rain-cover (Separately available).
Or wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Or install in a place keeping the waterdrops off.
Adjust the Secondary Activation area to "Deep"
(Outside).
Set the Secondary Activation area sensitivity lower.
Set the FLEX EYE sensitivity lower.
Check ADJUSTMENT 4.
Check ADJUSTMENT 1.
If the problem still persists, hard-reset the sensor.
(Turn the power OFF and ON again.)
Check the wires and connector.
Set dipswitch 16 to " OFF ".
Set the Secondary Activation area sensitivity higher.
Set the FLEX EYE sensitivity higher.
Wipe the detection window with a damp cloth.
Do not use any cleaner or solvent.
Contact your installer or service engineer.
Remove highly reflecting objects from the
Secondary Activation area. Or lower the Secondary
Activation area sensitivity. Or change the area depth
angle for Secondary Activation.
Adjust the Secondary Activation area to "Deep"
(Outside).
Remove highly reflecting objects from the
FLEX EYE. Or lower the FLEX EYE sensitivity.
Or change the area depth angle for FLEX EYE.
Adjust FLEX EYE to "Deep" (Outside).
East coast office
8510 McAlpines Park Drive, Suite 108
Charlotte, NC 28211 U.S.A.
TEL.: +1-800-877-6656
FAX.: +1(704)365-0818
WEBSITE: www.optextechnologies.com