Do not use this machine for other than its 19. Check damaged parts. Before further use of the intended use. If used for other purposes, JET machine, a guard or other part that is damaged disclaims any real or implied warranty and holds...
Page 3
27. Use recommended accessories; improper 33. Don’t use in dangerous environment. Don’t use accessories may be hazardous. power tools in damp or wet location, or expose them to rain. Keep work area well lighted. 28. Maintain tools with care. Keep tools sharp and clean for the best and safest performance.
11.0 Troubleshooting BGB-series Belt Grinders ....................12 12.0 Replacement Parts ............................. 13 12.1.1 Motor and Base Assembly – Exploded View - Models BGB-142/248/260-1 ........13 12.1.2 Motor and Base Assembly – Parts List – Model BGB-142 ..............14 12.1.3 Motor and Base Assembly – Parts List – Model BGB-248 ..............15 12.1.4 Motor and Base Assembly –...
4.0 Specifications for BGB-series Belt Grinders Model number BGB-142 BGB-248 BGB-260-1 BGB-260-3 Stock number 577100 577125 577150 577153 Motor and Electricals Motor type Totally enclosed fan cooled, induction Horsepower 1-1/2 Phase 115/230V (prewired 115V) 230/460V Voltage (prewired 230V) Cycle 60 Hz Listed FLA (full load amps) 11.5 / 5.8...
= not applicable The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
Failure to comply may cause serious An optional adaptor plate (not included) is available or fatal injury. for mounting the grinder to the JET JDCS-505 Dust Collection Stand. See your dealer or visit our Use only 3-wire extension cords that have 3-prong website for ordering information.
Table 1 is recommended. If in doubt, use the next heavier gauge. The smaller the gauge 6.2 Voltage conversion number, the heavier the cord. For models BGB-142, BGB-248, BGB-260-1: Conductor AWG # (American Wire Gauge) Remove four screws from control panel, and...
Figure 7-1: Belt Grinder identification 7.3 Abrasive belt tension 7.0 Adjustments To de-tension abrasive belt, turn tension knob counterclockwise and pull knob to the right. Disconnect machine from To tension, push knob to the left. The pawl will “click” power source before making adjustments. as it engages each ratchet tooth.
Running indicator light – Illuminates when motor is operating. 9.3 Abrasive belt replacement MODELS BGB-142/248/260-1 only: Disconnect machine from power source. On/off switch with safety key – Pull up to start Open side cover, and open dust cover by motor, push down to stop.
Collection Stand. Contact your dealer to order, or Install new belt and slide motor back to tension it. call JET at the phone number on the cover. Secure all covers and screws. # 414832 – Adaptor Plate Kit (for BGB-142/248) 9.6 Additional servicing...
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually.
12.1.2 Motor and Base Assembly – Parts List – Model BGB-142 Index No Part No Description Size 1 ....BGB248-101 ..... Switch Box ..................... 1 2 ....6295815 ....Phillips Round Hd Tapping Screw ......M3 x 10L ....... 8 3 ....
12.3.2 Belt and Housing Assembly – Parts List – Model BGB-142 Index No Part No Description Size 1 ....BGB248-201 ..... Compression Spring ..................1 2 ....TS-1502031 ....Socket Head Cap Screw ......... M5-0.8P x 12L ..... 2 3 ....
12.4.2 Belt and Housing Assembly – Parts List – Model BGB-248 Index No Part No Description Size 1 ....BGB248-201 ..... Compression Spring ..................1 2 ....TS-1502031 ....Socket Head Cap Screw ......... M5 x 0.8P x 12L ... 2 3 ....
Page 24
Index No Part No Description Size 61 ....BGB248-261 ..... Knob ......................1 62 ....F010391 ....Socket Head Set Screw ........... M5 x 0.8P x 5L ..... 1 63 ....BGB248-263 ..... Hub Supporting Shaft ..................1 64 ....
12.4.3 Belt and Housing Assembly – Parts List – Model BGB-260-1 Index No Part No Description Size 1 ....BGB248-201 ..... Compression Spring ..................1 2 ....TS-1502031 ....Socket Head Cap Screw ......... M5 x 0.8P x 12L ... 2 3 ....
Page 26
Index No Part No Description Size 61 ....BGB248-261 ..... Knob ......................1 62 ....F010391 ....Socket Head Set Screw ........... M5 x 0.8P x 5L ..... 1 63 ....BGB248-263 ..... Hub Supporting Shaft ..................1 64 ....
12.4.4 Belt and Housing Assembly – Parts List – Model BGB-260-3 Index No Part No Description Size 1 ....BGB248-201 ..... Compression Spring ..................1 2 ....TS-1502031 ....Socket Head Cap Screw ......... M5 x 0.8P x 12L ... 2 3 ....
Page 28
Index No Part No Description Size 61 ....BGB248-261 ..... Knob ......................1 62 ....F010391 ....Socket Head Set Screw ........... M5 x 0.8P x 5L ..... 1 63 ....BGB248-263 ..... Hub Supporting Shaft ..................1 64 ....
Index No Part No Description Size ....414832 ...... Adaptor Plate Kit, BGB-142/248 (#1 thru 5) ............ 1 ....TS-149105 ....Hex Cap Screw ............M10 x 1.5P x 35L ..4 2 ....TS-2361101 ....Lock Washer ............M10 ......8 3 ....
12.6.1 Adaptor Plate (OPTIONAL) – Exploded View – Model BGB-260-1/260-3 12.6.2 Adaptor Plate (OPTIONAL) – Parts List – Model BGB-260-1/260-3 Index No Part No Description Size ....414833 ...... Adaptor Plate Kit, BGB-260-1/260-3 (#1 thru 5) ..........1 ....TS-149105 ....Hex Cap Screw ............M10 x 1.5P x 35L ..4 2 ....
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®...
Need help?
Do you have a question about the BGB-142 and is the answer not in the manual?
Questions and answers