Jet BGC SERIES Operator's Manual
  1. Manuals
  2. Brands
  3. Jet Manuals
  4. Grinder
  5. BGC SERIES
  6. Operator's manual

Jet BGC SERIES Operator's Manual

Bench grinders
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
BGC SERIES
BENCH GRINDERS
www.jetequipment.com

Advertisement

Table of Contents
loading

Related Manuals for Jet BGC SERIES

Summary of Contents for Jet BGC SERIES

  • Page 1 OPERATOR’S MANUAL BGC SERIES BENCH GRINDERS www.jetequipment.com...

  • Page 2: Specifications

    Vancouver office. Proof of purchase date and an explanation of the problem must accompany the merchan- dise. If our inspection discloses a warrantable defect JET will repair or replace the product at our option and return the product freight prepaid.
  • Page 3 READ ALL INSTRUCTIONS BEFORE OPERATING GRINDER WARNING 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE LOOSE TOOLS AND WRENCHES. Always check to see that tools and adjusting wrenches are removed from tool before turning it on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4.
  • Page 4 19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
  • Page 5 ing from the adapter must be connected to a permanent ground such as a properly grounded outlet box. CAUTION. In Canada only the Grounding as shown on Fig. A will be acceptable. Also the extension cords shall be CSA certified SJT type or better. FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING GRINDER Wear eye protection that complies with ANSI Z87.1 specifications.
  • Page 6 SWITCH The switch is located on the front of the grinder near the bottom. To turn the tool “ON" depress the rocker switch at the left side near the word “ON". To turn the tool “OFF" depress the right side portion of the rocker switch, near the word “OFF".
  • Page 7 INSTALLING THE EYE SHIELDS TURN OFF AND UNPLUG BENCH GRINDER. Remove the steel strip from the top surface of each Eye Shield by removing the two screws. Install the shields, (they are identical and will fit either side) to the brackets, as shown in Figure 3.

  • Page 8: Changing Accessories

    CHANGING ACCESSORIES TURN OFF AND UNPLUG THE BENCH GRINDER. USE ONLY GRINDING WHEELS THAT MEASURE 6 INCHES IN DIAMETER FOR MODE BGC-6 AND 8 INCHES IN DIAMETER FOR MODEL BGC-8. MODEL BGC-6 HAS 1/2 INCH ARBORS ON BOTH SIDES. MODEL BGC-8 HAS 5/8 INCH ARBORS ON BOTH SIDES.

  • Page 9: Grinding Wheels

    OPERATING INSTRUCTIONS As you face your bench grinder, the wheel on the left is a medium (60 grit) wheel for medium material removal and general purpose grinding. The wheel on your right is a coarse (36 grit) wheel for fast material removal. To operate the bench grinder, put on safety glasses and turn the tool on.
  • Page 10 DESCRIPTION MAXIMUM SAFE SPEED GRINDING WHEELS 1/2" Face, 6" dia. 60 Grit Medium Grinding Wheel 3,825RPM 5/8" Face, 6" dia. 60 Grit Medium and 36 Grit Coarse Grinding Wheel 4,136RPM 3/4" Face, 6" dia. 60 Grit Medium Grinding Wheel 4,136RPM 3/4"...
  • Page 12 BGC-6 (240153), BGC-8 (240154) PARTS LIST Please state the model number of your grinder when ordering parts. NO. DESCRIPTION Q’TY NO. DESCRIPTION Q’TY ASSEMBLY OF SHAFT CONDENSOR FIXER 1 ROTOR TOOTH WASHER STATOR SCREW COPPER WIRE ELECTRIC CORD STATOR HOUSING SCREW BASE TOOTH WASHER...

Table of Contents