Advertisement
ATTACHING AIR TUBE COMBINATIONS TOR CIIASSIS PI,AN ONI,Y
When oil burner chassis and air tube combination are packed separately, the
burner must be assembled as follows:
l- Lay burner chassis on its back as shown at right. Insert air tube into burner
chassis lining up the 3 holes in the chassis with the 3 holes in the air tube.
Install the 3 screws s/s long and secure.
2- Install proper nozzle into gun assembly. Loosen and remove the two
screws located on the transformer top plate at the front of the burner
chassis and swing open. Slide drawer assembly into air tube (see Fig. 2).
3- Once installed, adjust grun assy., either back or forward to position nozzle
from head, For correct positioning (see Fiq. 3). Secure the slide plate by
tightening thumb screw at side of housing. Attach flared nut of Oil Line
Assy., (Copper Oil Line) to the end of this adapter fitting as shown.
Install arrow decal as shown so position of Drawer Assy. is always known
(see Fiq. 4).
Recheck for nozzle centering before burner is installed (see Fig, l). Make
sure electrode tips ciear retention head.
INSERT "SE'' SERIES GUN SETTING GAUGE
(AS SHOWN EELOW) TO CHECK NOZZLE
POSITION AND ELECTRONIC SETTING.
Figure 3
ELECTRODE
BURNER AIR TUBE
NOZZLE
FLAMELOCK CONE
"sR" SEFTES
GUN SETTING GAUGE
ALL DIM'S AS SHOWN UNLESS OTHEFWISE SPECIFIED
'/a "
t / 8 "
BURNER OIL PIPE
B URNE R A I R T U BE
4%
FLAMELOCK HEAD
NOZZLE FACE TO FACE OF INNER AIR CONE
TRACK FOR GUN ASSEMBLY
AOJUSTMENT BRACKET
Figure 1
t/2"
Figure 2
EG-l - 21755-001 Rev. 0406-20-88 PAGE 6
ATTACHING AIR TUBE COMBINATIONS FOR CHASSIS PLAN ONLY
When oil burner chassis and air tube combination are packed separately, the
burner must be assembled as follows:
1- Lay burner chassis on its back as shown at right. Insert air tube into burner
chassis lining up the 3 holes in the chassis with the 3 holes in the air tube.
Install the 3 screws
%
long and secure.
2- Install proper nozzle into gun assembly. Loosen and remove the two
screws located on the transformer top plate at the front of the burner
chassis and swing open. Slide drawer assembly into air tube (see Fig. 2).
3- Once installed. adjust gun assy., either back or forward to position nozzle
from head. For correct positioning (see Fig. 3). Secure the slide plate by
tightening thumb screw at side of housing. Attach flared nut of Oil Line
Assy., (Copper Oil Line) to the end of this adapter fitting as shown.
Install arrow decal as shown so position of Drawer Assy. is always known
(see Fig. 4).
Recheck for nozzle centering before burner is installed (see Fig.
1).
Make
sure electrode tips clear retention head.
•
Figure 1
INSERT "SR" SERIES GUN SETTING GAUGE
(AS SHOWN BELOW) TO CHECK NOZZLE
POSITION AND ELECTRONIC SETTING.
•
1(2--
II
~ -£1/8
L1
cHB:1~w
~~
-
~~I(B"
FLAMELOCK HEAD
ELECTRODE
FLAMELOCK CONE
"SR" SERIES
GUN SETTING GAUGE
~
ALL DIM'S AS SHOWN UNLESS OTHERWISE SPECIFIED
NOZZLE FACE TO FACE OF INNER AIR CONE
NOZZLE
TRACK FOR GUN ASSEMBLY
ADJUSTMENT BRACKET
~-+_
GUN ASSEMBLY
ADJUSTMENT BRACKET
BURNER AIR TUBE
DECAL--==tr:r-
ELECTRODE SUPPORT
Figure 2
EG·1 . 21755-001 Rev. 04106-20-88
PAGE 6
Advertisement
