Hunt Electronic HVRM-T1600L Install & User's Manual

16 channel h.264
Hide thumbs Also See for HVRM-T1600L:
Table of Contents

Advertisement

English
HVRM-T1600L
Install & User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HVRM-T1600L and is the answer not in the manual?

Questions and answers

Summary of Contents for Hunt Electronic HVRM-T1600L

  • Page 1 English HVRM-T1600L Install & User’s Guide...
  • Page 2: Introduction

    Introduction Thank you for purchasing a HUNT digital video recorder. This manual is for HVRM-T1600L. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual. This user manual and the software and hardware described here are protected by copyright law.
  • Page 3 Caution As this equipment undergone EMC registration and suitable for business purpose, distributors and users are aware of this point. FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment.
  • Page 4: Important Notice

    Installaction & User Manual Important Notice 1. Do not place heavy objects on the top of the product. 2. This equipment is indoor use and all the communication wiring are limited to inside of the building 3. Product is for indoor use. It is not weatherproof. Use product with referring to its environmental specifications (Temperature &...
  • Page 5 B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
  • Page 6: Table Of Contents

    Installaction & User Manual Contents INTRODUCTION ................2 KEY FEATURES ................11 INSTALL MANUAL................14 FEATURE ................. 14 Supplied Accessories ....................14 Description & Function ....................15 1.2.1 Front ........................15 1.2.2 Rear ........................17 1.2.3 REMOTE CONTROLLER ..................18 2.
  • Page 7 Menu Structure ......................47 Function Menu ......................47 Factory Reset ....................... 48 MONITORING ................53 Basic Screen ......................53 Single Full Screen Mode ..................... 53 Multi Screen Mode ......................53 Screen Description ....................... 53 Auto Switch Mode ......................54 4.5.1 System Standard Mode ..................
  • Page 8 Installaction & User Manual SEARCH MODE ......................61 5.2.1 Time Search ......................61 5.2.2 Schedule Search ....................61 5.2.3 Event Search ......................62 5.2.4 Thumbnail Search....................63 Copy..........................64 5.3.1 CD/DVD ........................ 64 5.3.2 RE4 ........................65 5.3.3 AVI ........................66 6.
  • Page 9 Recording setup ......................103 6.6.1 Program setup ..................... 103 6.6.2 Manual/Schedule recording setup ................ 105 7. WEB VIEWER ................110 System requirement....................110 Login .......................... 110 User Setup ......................... 111 Browser available ....................... 112 Monitor ........................113 7.5.1 Screen division and changing video position ............113 7.5.2 Move to Playback ....................
  • Page 10 Installaction & User Manual 9 USER MANUAL FOR MOBILE VIEWER ........ 124 Log-In page ........................ 124 Monitoring page ......................124 TROUBLE SHOOTING ..............126 THE WAY TO CHECK THE MANUFACTURING DATE ....128 AVAILABLE HDD ................129 COMPATIBLE CD/DVD LIST ............129 SPECIFICATION................
  • Page 11: Key Features

    KEY FEATURES Monitoring Screen Supprots real live video with high resolution per each channel and variable display mode.  Real H.264 Video  Various monitoring Single, 4ch, 9ch, 10ch, 16ch  Auto Switching(AUTO) Composite 4 ea, DVI 2ea Audio Recording Supprots real-time audio input and recording ...
  • Page 12 Installaction & User Manual Search / Playback It supports variable and convenient functions for search & playback.  Play back by time,date,channel  Easy and convenient search using mouse  Pre/Post search from a freeze frame  Play back by Event (Sensor, Video Loss, Motion Detection, Text) ...
  • Page 13  Supports User friendly GUI and mouse function  Easy and simple firmware upgrade thru. USB memory  PTZ Control (SPEED DOME), PRESET fucntion  Available to control up to 16 DVRs with one remote controller...
  • Page 14: Install Manual

    Installaction & User Manual Install Manual 1. Feature Supplied Accessories Unpack and check all the items as below AC Cord, Remocon, Setup CD, HDD Fixing Clamp, SATA Cable, HDD Fixing Screw, Rack Mount...
  • Page 15: Description & Function

    Description & Function 1.2.1 Front 구분 기능 DVD-Multi Back up use for recorded data by DVD/CD media Back up USB Port Use connecting USB memory or Mouse Power LED Display Power status Network LED Display network status Recording LED Display recording status. Playback LED Display playback status.
  • Page 16 Installaction & User Manual Remote controller receiving sensor Enter/Play To select menu or enter playback mode. ◀/REW To move or select in menu and change replay speed to reverse direction in playback mode ▶/FWD To move or select in menu and change replay speed to forward direction in playback mode.
  • Page 17: Rear

    1.2.2 Rear Input/ Output name Description Power connector Socket for AC100V~AC240V power cord. CH1~16 BNC input for camera connection Loop out BNC output(Loop) for camera connection. Monitor 1~4 BNC connection for monitor output. Audio input(RCA) RCA connection for Audio input Audio output Speaker output terminal.
  • Page 18: Remote Controller

    Installaction & User Manual 1.2.3 REMOTE CONTROLLER It is available to use all functions of DVR. If several DVR are set with unique ID numbers, they can be controlled with one remote controller. To use remote controller, it is necessary to set ID first which want use.
  • Page 19 SEARCH To indicate search menu CHANNEL BUTTON To select channel SELECT Not use In case of selecting over 10 (+10 + 1) Not use Not use MENU Covert to menu screen HELP Not use ◀/REW Move setting menu to left direction/REW ▶/FWD Move setting menu to right direction/FWD ▲/PAUSE...
  • Page 20: Installation

    Installaction & User Manual 2. Installation Installation and Connection 2.1.1 Connecting & Running 2.1.1.1 Connecting camera Connect CCTV camera to DVR with BNC cable as below. - The video type for all channels should be either NTSC or PAL, not be combined both - DVR sets video signal’s impedance (75Ω) automatically.
  • Page 21: Supplying Power

    2.1.1.3 Supplying Power Connect power cable as below. - When supplying power, DVR starts booting automatically. - In order to cut off power, press power switch on DVR front during 5 seconds, then select “YES” after appearing a pop-up window. - For supplying power again, push the Power button.
  • Page 22: Running Osd Menu

    Installaction & User Manual Running OSD menu 2.2.1 OSD menu configuration Press [MENU] in keypad of front to open configuration menu as below Main Menu Sub Menu Configuration (1) Main Menu : The selected tab is show in bright color and the related sub-menu will be shown left- below the tab.
  • Page 23: Setting Remote Controller

    Keep pressing [▲/▼], [◀/▶] arrow button until the word is looking for and press Enter. In case of deleting input word press [], spacing words press [] button. To exit from dialogue box, press [Enter] after finishing word input. 2.2.2 Setting remote controller 2.2.2.1 Setting ID of DVR When controlling several DVRs with one remote controller, set Remote Control ID as follows.
  • Page 24: Installation Examples

    Installaction & User Manual 2.2.2.2 Setting ID If several DVRs are with unique ID numbers, they can be controlled with one remote controller. To select a specific DVR, keep pressing the ID button of remote controller until a buzzer sounds during 2 seconds.
  • Page 25 2.2.3.2 Advanced configuration Connect camera, monitor , audio, sensor, relay etc.. 2.2.3.3 External storage & back up configuration Use USB for back up.
  • Page 26: Basic Setting

    Installaction & User Manual 2.2.3.4 Internet / Intranet configuration 2.2.4 Basic Setting 2.2.4.1 Viewing Image When power is on, eDVR starts automatically and displayed in basic 16ch-split screen after booting. <Reference> If user password is set, a prompt for entering the password will be appeared. Factory default is reserved as not responding keypad on DVR front (It is not from factory default)
  • Page 27 2.2.4.2 Setting Date & Time - Press [MENU] button and select “ System” when OSD menu is appeared. - Select“Date/Time”and press [Enter] button. Time Zome Use the left or right arrow key on the front or the mouse wheel to select your time zone. Each press of the arrow keys changes the time zone.
  • Page 28 Installaction & User Manual (1) Select yes or no of using NTP. (2) Select NTP mode among Client, server, Both using directional key. [◀/▶] or [▲/▼] (3) Select Public or Both. (4) Enter server IP address when configuring server type by Local. (5) Configure communication interval with server.
  • Page 29 (2) Select using [◀/▶] or [▲/▼] arrow button and select “YES”, then, press [ENTER] button. To cancel, press [ESC] button. 2.2.4.3 Record Setting Select “Record” pressing menu button in front. Program Setting Set resolution, frame rate, quality by each channel that user want record in “Program” of record menu...
  • Page 30: Connecting And Configuring Dio Ports

    Installaction & User Manual Schedule Setting Set recording mode as “Schedule & Event” and set by date/ time. Checking method for recording <Reference> If recording setting is finished correctly, “REC LED” in front is flickering. In addition, it is marked [S] indicating that all channels are recording.
  • Page 31: Connecting And Configuring Sensor

    - Standard wire : Pie off the wiring cover 8~10mm and solder it. Wire gage should AWG 22~26. - Sold wire : Peel off the wiring cover 8~10mm and solder it.Wire gage should be AWG 20~26. 2.3.2 Inserting & removing wire To insert &...
  • Page 32 Installaction & User Manual Connecting sensor input Connect S1 ~ S16 with referring the following image. It shows to connect a dry contact (Please refer “Wire Handling”. Setting Sensor (1) Press [Menu] button and select “Event” when OSD menu is appeared. (2) Move to sub menu pressing [Enter] or using [▼] button and select [Enter].
  • Page 33: Connecting Relay And Setting

    (2) Select sensor that user want set and set type. (3) Press [ESC] after finishing value setting. 2.3.3.2 Connecting relay and setting Specification In order to run relay output of DVR normally, the following conditions are required. Output Ch. 2EA relay outputs Output type Dry contact SPEC...
  • Page 34: Connecting Serial Port

    Installaction & User Manual 2.3.3.3 Connecting serial port Configuring serial ports for Pan/Tilt/Zoom If DVR supports thru. COM port, it is available to connect PTZ camera and control it. For a list of supported protocols, please refer to the list on the OSD configuration menu. The following figure shows how to connect PTZ camera to RS485 (COM2).
  • Page 35 COM2/COM3 diagram (RS-485) COM1 diagram (RS-232) Available PTZ is same as below table. Model name Manufacturer Webgate Keyboard KBD300A, WGI SPD1800/2600 Webgate WKC-100 keyboard BOSCH AutoDome, TC8560X-4 Bosch Pelco PELCO(P), PELCO(D) Honeywell Honeywell 755/655, HRX-2000, ScanDome2 Sony EVI-D3x Sony VT VPT-4x SDZ160/330, Samsung SPD, Samsung Techwin Keyboard SCC3000, Samsung SRX-100B...
  • Page 36 Installaction & User Manual Samsung Electric Samsung SCC641 Panasonic WV-CS850 Panasonic LG GAC-PT2 Keyboard KBD300A, WGI SPD1800/2600 Honeywell Merit-Lilin FastDome Merit Elmo Elmo PTC200C Canon VC-C4 Canon HTC-230S Dongyang Unitech RVision Elbex Elbex VIDO VIDO Vicon VICON Hunt Hunt ORX-1000 Sysmenia LiveEye Fine CRR-1600...
  • Page 37 2.3.3.4 Connection to external device via Serial port Text input device connection (ATM / POS / Access Control) Using COM1/RS232, TEXT DATA can be recorded with synchronizing POS/ATM.. Like above picture, connect COM1/RS232 (9pin D-Sub) in Device menu and configure Serial and Text Serial (COM1) Setup (1) OSD Select “Device”...
  • Page 38: Usb Device Connection

    Installaction & User Manual (2) Selecting COM1 and configure “Text”in Device (3) Setup the value of Baud Rate/Parity/Stop bit/Data bit with the device. Text Setup (1) Select “Deice” on OSD, and move to sub menu. (2) Select “Text”and configure relevant text information. <Reference>...
  • Page 39 In case of normal connection, if executing Copy menu, disk will be recognized same as below and Set copy range  Select Drive  Execute Copy [CD/DVD Copy] [RE4 Copy] Select the channel to copy.
  • Page 40 Installaction & User Manual [AVI Copy] <Reference> A USB Flash memory which should install additional program on Windows OS, can not be recognized. 2.3.3.6 Video In/Out connection Video Input/Output is Loop through and check the connectivity automatically and set end resistance.
  • Page 41: Hdd

    2.3.4 HDD ※ Please, refer to Appendix for available HDD list. 2.3.4.1 HDD registration and format After mounting HDD and booting system, “Disk Manager” will execute automatically. If not, please, check the connectivity of HDD (1) Press [Enter] button in “Disk Manager” (2) Using [▲/▼] Key, select new HDD(Displayed [No] on Enabled item) and press [Enter].
  • Page 42: Remote Monitor And Control

    Installaction & User Manual has a problem, and press “Enter” Key. (3) “Removed disk will be Confirmed” message will be pop-up and select “Yes” to delete it from the list. (4) Select the new HDD from the list and press “Enter” key. (5) Select “Yes”...
  • Page 43: Network Configuration

    <Reference> To protect DVR damage, after connecting Ethernet cable, input Power. Please, check Ethernet cable connection firmly. Input power on DVR and check their connectivity. 2.3.5.2 Network configuration Ethernet Set type as Ethernet and input IP, Netmask,Gateway, DNS. The way to input is using directional key or mouse wheel. PPPoE Set type xDSL, and move to xDSL menu.
  • Page 44: External Device Connection

    Installaction & User Manual 2.3.6 External device connection DVR has external Storage Device Interface and 1 ea of eSATA port. Using eSATA port, user can expand Storage capacity up to 8TB. <Note> Since some of eSATA device can not be compatible with DVR, before the usage, please, contact the seller and check its compatibility in advance.
  • Page 45 <Note> 1) The network cable connected to DVR should be Gigabit Ethernet Cable (Category-6). If not, it is not connected to DVR. 2.3.7.2 Set ID Configuration Set ID using Rotary Switch located on the back. This ID is used as IP Address of NVS04R and the form of IP address is 10.10.20.XXX.
  • Page 46 Installaction & User Manual 2.3.7.3 Power connection and operation (1) Connect power as below. (2) As soon as power is connected, the device starts booting. <Note> 1) It takes around 1 minute to connect NVS04R and DVR after connecting power. Four LEDs at the front starts blinking and they are fully on when connection is completed.
  • Page 47: User Manual

    User Manual 3. Menu Use Menu Structure The menu structure will be shown like below image, and each menu setting method descriped from chapter 4 to chapter 6. Function Menu To run Function menu, please, click the right button of mouse or push “Help” button on the front panel.
  • Page 48: Factory Reset

    Installaction & User Manual Function of Playback Factory Reset In order to reset value to factory value, go to System Setting->System->Setting, and once press Factory Reset then the warning message will be appear, click “Yes” to reset the DVR value to factory.
  • Page 49 User No Password used Setup DVR Alias DVR0 DVR Keyboard ID Remote Controller Utility Language English Firmware Update >> System Log >> Factory Reset >> Network Type Ethernet DHCP IP addr Default IP Net Mask Default Net Mask Gateway Default Gateway Network DNS1 4.2.2.1...
  • Page 50 Installaction & User Manual Contrast PTZ Home Idle Time PTZ Port None PTZ Address Monitor Alarm Pop-up(Sec) User Sequence << Configuration SEQ Time(Sec) Monitor Covert >> Multi Mode 4E, >> VGA Mode 800x600@56Hz Infor Level >> Audio Channel Audio Recording Audio Audio Gain Sync Video Channel...
  • Page 51 Event Duration >> Playback Deinterlace Normal Resolution All D1 Frame Rate All 6 Quality All Q5 Program Event Resolution All D1 Frame Rate All 6 Quality All Q5 Factory Default value HVRM-T1600L Rec mode Normal Event List Half Half Half Half...
  • Page 52 Installaction & User Manual Half Half...
  • Page 53: Monitoring

    4. Monitoring All analog video image channels connected to DVR is displayed to screen by Power connection. It is to utilize all monitoring mode of DVR. Basic Screen After Power connection, the DVR operates on automately. It boots with LED on. After booting, 16 channel screens are displayed.
  • Page 54: Auto Switch Mode

    Installaction & User Manual Auto Switch Mode There are System Standard modes and User Defined mode in Auto Switch mode. And Users Sequence mode operates by the press [SEQ] button. 4.5.1 System Standard Mode By [Auto] button, it can monitor auto switching of all channels. Press [MENU] for the setting switching term or using mouse click menu icon from function menu.
  • Page 55: Event Screen

    There are 16 modes for user sequence mode. Event Screen When there is an event occurred, the green color [M] and red color [S] will be display from status bar. In case of [M] displayed, the camera name will be turned to green color, and it will turn to yellow when Motion Detection event finish.
  • Page 56: Zoom Screen Mode

    Installaction & User Manual 1. If Alarm Pop-up Hold (sec) set to Off, Alarm Pop-up will not operate. 2. If Alarm Pop-up Hold (sec) set to Keep, it does not return to previous screen before press any button. Zoom Screen Mode From single full screen mode, press [FUNC] and D-Zoom button then select + button to activate zooming the image.
  • Page 57 Model Manufacturer Bosch BOSCH AutoDome, TC8560X-4 Pelco PELCO(P), PELCO(D) Sony EVI-D3x Sony VT VPT-4x AD SpeedDome SungJin SJ372R1 SungJin Samsung Electric Samsung SCC641 Panasonic Panasonic WV-CS850 SDZ160/330, Samsung SPD, Samsung Techwin Keyboard SCC3000A, Samsung SRX-100B LG GAC-PT2 Honeywell Keyboard KBD300A, WGI SPD1800/2600 WKC-100 webgate Merit-Lilin FastDome...
  • Page 58: Pan/Tilt

    Installaction & User Manual Sysmenia ORX-1000 Fine CRR-1600 LiveEye Tokina Tokina Kodicom KRE Kodicom Nuvico Nuvico Press desired channel button. Press PTZ button from front panel or click PTZ icon from function menu with mouse. PTZ menu (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset) will be appear. Then press [Enter] button or click from mouse.
  • Page 59: Auxiliary Off

    4.9.6 Auxiliary Off This menu is used to stop operation of specific function of PTZ device. Using up / down button or mouse wheel to select the Aux Number. Select Off and press Enter button or click from mouse. 4.9.7 Menu It is to go into connected PTZ’s menu, using up/down/left/right and enter key from front panel for setting the menu, and press ESC button for exit the menu.
  • Page 60: Playback

    Installaction & User Manual 5.Playback Playback Mode 5.1.1 Playback on Standard monitor (16 / 9 division) Please, push play button in monitoring mode or mouse click play button in Function menu. If pushing Play button or FWD button, video playbacks in forward direction at 1× speed. If pushing REW button, video playbacks in reverse direction at 1×...
  • Page 61: Search Mode

    SEARCH MODE This menu is to playback specific time data from the time frame and searching log at Playback mode. There are Time, Calendar, Event, Thumbnail mode. Please, push Search button on the front panel or click in Function menu. 5.2.1 Time Search Select date and time to search and playback video will be moved to the selected point.
  • Page 62: Event Search

    Installaction & User Manual Month : Select Month to search. With mouse wheel, user can change it. Date : Select Date to search. With mouse, select the date and decide the time by wheel. Time : Select the time and push Enter button to play back. 5.2.3 Event Search User can search by all channels, some of channels, all events, motion detection, sensor in...
  • Page 63: Thumbnail Search

    5.2.4 Thumbnail Search Search certain channel by thumbnail type. If select the searched thumbnail, selected date and time video will be played back.. Channel : Select the channel and change the value by direction key or mouse wheel. Start Time : Input the date and time for starting search and change the value using up-down direction key or mouse wheel.
  • Page 64: Copy

    Installaction & User Manual Copy This is for copying recorded video. There are CD/DVD and RE4 and AVI type. Copy function is supported to be used by user who has the authorization. For authority configuration, please, refer to 6.9.3 Security. To use copy function, press [COPY] or Click Copy button in Function menu.
  • Page 65: Re4

    : Select end date and time to copy using up-down key or mouse wheel. Select Disk : Select the media to copy using Enter button on Select Disk. Start : Start Copy. Press Start button with Enter or click the left button of the mouse.
  • Page 66: Avi

    Installaction & User Manual Channel : To pop up the channel selection window, press Enter or use mouse wheel. Select Channel : use can select some or all channels and after selecting channel, press Enter or click mouse left button. Start time : Set start date or time to copy.
  • Page 67 FAT32 Format : Format USB Memory or HDD not formatted. Caution : If copied file is not played back, please, install integrated codec first.
  • Page 68: Configuration

    Installaction & User Manual 6. Configuration Recording Structure There are 4 modes in DVR recording. Configuration relation structure is like below. Please, refer to the below each item for detailed recording configuration. System Setup Time and Disk and authority can be configured. 6.2.1 Date/Time Time set should be configured prior to the recording.
  • Page 69: Time Setup

    6.2.1.1 Time Setup Caution: under recording, if user changes Time, it will affect time change on previously recorded video data in accordance with. Therefore, we recommend backup before time change. Press Main Menu of Function or [MENU] button on the front panel. Move to “quick setup”...
  • Page 70: Ntp Setup

    Installaction & User Manual <Caution> Except date/time configuration, other configuration records automatically, but “date/time” configuration influences critical effect to HDD recording file system, It doesn’t record automatically. To apply the changed value, user must press [apply] button. 6.2.1.2 NTP Setup NTP(Network Time Protocol) make time of connected devices synchronized.
  • Page 71: Disk

    NTP Server Loc. When NTP mode is client, it is on Enable. Configure yes or no wether NTP server is in Local Network or Public. NTP Local server IP In NTP local server Enable, configure server ip. Input IP address of NTP server or DVR set by NTP server In local network.
  • Page 72 Installaction & User Manual This function makes recording data seen during the limited area. For instance, if setting block playback by 2 day(Pic 2) among 10 days, Just allowed 2 days data can be played back. Block Recording This option is to record only the date you selected. For example, if you select 3 days then DVR will record up to 3 days, and keep overwriting 3 days period of data Disk Full Alarm Warning...
  • Page 73: Disk Status

    - Enabled : Press [Enter] in No mode or scroll mouse wheel. Notice window pops up and show user the message like below. - Caution : This Disk is not available without format. Will you format Disk? - If selecting No, keep previous data and HDD will be Enable to use. - If selecting Yes, delete previous data and HDD will be Enable to use.
  • Page 74 Installaction & User Manual Recorded Video data via Mirroring function can playback in another DVR. But if user want to use the HDD for recording, it should be formatted again. □ File system supporting Max. 32TB □ Support max 8 ea of NVS via Cascade Network Port. □...
  • Page 75 Mirroring HDD for recording, it should be formatted. Mirroring configuration - Off : All mounted HDD will be recorded in order without Mirroring. - DVR : Mirroring recording only with internally mounted HDD (not HDD in NVS04R) - NVS : Mirroring recording only with HDD in NVS04R which is connected to DVR. (not HDD in DVR) - All : Mirroring recording with all HDDs in DVR and NVS04R.
  • Page 76 Installaction & User Manual <Note> 1. For Mirroring function, HDDs capacity and model for Recording and Mirroring should be same. If not, it won’t work. But, in case that HDD capacity is same but just different model, sometimes, it can not work properly.
  • Page 77 When using Mirroring function, according to configuration option, DVR system performance will be down and due to this reason, recording configuration will be adjusted automatically like below table chart. 1) Maximum recording performance per model with NVS Mirroring configuration. [HVRM-T1600L Model] NVS Mirroring Recording Setting Resolution Quality...
  • Page 78: User Setup

    Installaction & User Manual Loc : Mirroring HDD name Free : HDD free space From : Date and time of Start recording. To : Date and time of End recording State : If free space is enough, it is displayed by Mirroring and if 0%, displayed by Replace. With these information, user can notice the HDD replacement timing.
  • Page 79 [Check-1] [Check-2] In the other hand, if all are set by O[check-2], all users can use the functions in accordance with Each users authority. For example, as you can see the below picture, User1 can use PTZ, Relay off, power On, N/mike functions are available, user 2 just can use menu and N/mike functions.
  • Page 80: Utility

    Installaction & User Manual Password input box is displayed. Password can be input with front figure button or text input window. After inputting 8 digit figures, click “Change” button. After that, message pop up window will be shown and press “Yes”. Authority User can use only authorized functions.
  • Page 81 DVR Alias Set the name of DVR. DVR Keyboard ID This menu is to set the address of keyboard when using all functions of DVR by keyboard. Factory default is “1”. If user want to control various DVR by one keyboard, its address should be set with the different value.
  • Page 82 Installaction & User Manual System Log System Log shows boot status of system and user and configuration etc. Factory Reset Change all configuration value by factory default. Config Import/Export This function can allow user to save the configuration DVR by USB, and can export its value to other DVR.
  • Page 83 If data transmission is done, you will see the message like below. Config Import menu can import the configuration value of the saved DVR. Please, insert USB memory which containing Export configuration data to USB port of the DVR, click import button on Config Import/Export menu. All relevant configuration value will be updated to the DVR at once.
  • Page 84: Network

    Installaction & User Manual System Information Display recording status and system configuration of DVR Caution : This function is allowed only for system administrator. Network This is menu for configuring network.
  • Page 85 Type Configure type of Network (Ethernet/xDSL). If connected to cable modem or Lan directly to DVR, configure by “Ethernet”. If DVR connects to xDSL- one of PPPoE type, configure xDSL. But if it is not type of PPPoE, configure ‘Ethernet’. DHCP With DHCP (Dynamic Host Configuration Protocol), all hosts connected to Lan can get Public IP address temporary.
  • Page 86: Xdsl

    Installaction & User Manual Bandwidth Menu for configuring network data transmission capacity. Without any additional configuration, it works but if user want to set, please, ask for administrator. 6.3.1 xDSL DVR is connected to xDSL line and use PPPoE type, please change type by xDSL and configure user ID and Password.
  • Page 87: Radius

    WRS Interval For continuous register, register interval should be set to ‘WRS Interval’. According to set value of static IP address, it renews the information in WRS server regularly. If user registers the interval ‘0’ or DVR does not transmit any data for 2 days, the data is removed from WRS. WRS URL This menu is to set server address to register.
  • Page 88: Device Setup

    Installaction & User Manual ‘User ID’, Password’ and ‘Radius Shared Key’are needed from administrator of Radius server after forwarding DVR account information to him. Use ‘ID/Password/Shared key’ to register unit to Control Center. Click the Radius Shared Key and enter ID, Passward, Shared Key. Registration is completed of all information is correct.
  • Page 89: Camera Setup

    6.4.1 Camera Setup Select the camera to configure in Channel menu. 6.4.1.1 Title Configure camera name. If pressing [Enter] button or click mouse, test menu will be shown. For text string, text input box will be shown. Use directional key for text input. With mouse, just click the text.
  • Page 90: Monitor Setup

    Installaction & User Manual 6.4.1.3 AGC (Auto Gain Control) AGC is the function to control the range of video signal input from camera connected. Configure Enable/Disable using directional key or mouse wheel. 6.4.1.4 Brightness/Contrast It can control Brightness and Contrast of video. After press [ENTER], use left/right button or mouse wheel to set the value wanted from each “–9”...
  • Page 91: Audio Setup

    DVI Resolution There are 9 resolution can be select 800x600@56Hz, 1024 x 768@60Hz, 1280 x 720@50Hz,1280 x 720@60Hz, 1920 x 1080p60, 1920 x 1080i50, 1920 x 1080i60, 1920 x 1080RB. Display information Display information is to configure which information will be shown on live view and playback view.
  • Page 92: Text Setup

    Installaction & User Manual Synchronize Video Channel Configure which channel is matched with the input audio. But this function is applied only on recording. Audio out in live view will be covered in Voice Mixing below. Default set is Audio no.1 to channel no.1.
  • Page 93: Serial Setup

    Sync Text with Select channel to synchronize with text. Header check It has the various type of data input from the external device (Access Control, POS, ATM etc). Like VSI Pro, VSI Pro Hydra, and Star Finger 007, it is not needed when the protocol of these device have implemented on the device.
  • Page 94: Ptz Setup

    Installaction & User Manual Serial Port Select Serial port. Device Select the connected device. Interface Configure which interface user uses. COM1 is for RS-232C, COM2 and COM3 is for RS-485 Baud rate/Parity/Stop Bit/Data Bit In put suitable value according to external device. 6.4.5.1 PTZ Setup Additional configuration for PTZ Address PTZ Home...
  • Page 95: Event Setup

    PTZ Idle Time If it has no movement during configured time, shift to PTZ Home. PTZ Port Select Port for PTZ PTZ Address Configure the address configured in PTZ. 6.5 Event Setup There are 5 items such as event, Text, Sync Event,Preset, System event. 6.5.1 Event Check There are 3 items –...
  • Page 96: Sync Event

    Installaction & User Manual • INDEX : Schedule configuration from 1 to 50 • Weekday • Time • Delete : delete INDEX How to configure If configuring INDEX,weekday,time, they are displayed on the table. If clicking and selecting start time and end time of recording on the table, Index,weekday,time will be shown on the table.
  • Page 97 time. E-mail works by configured time interval. Normal Event Source User can configure Sensor, motion detection, V-loss, Text. Sensor V-Loss Text System Event source System Event source can configure Bad block, Disk full, Fan error, authorization failure, WRS registration failure. E-Mail There are two ways for E-mail transmission –...
  • Page 98 Installaction & User Manual USE (SMTP-Auth) If user selects Authentication in USE, SMTP-Auth function will work. SMTP-Auth method is the way that E-mail will be authorized by SMTP server and then it will be transmitted to receiver. E-Mail Address Input E-mail address of receiver. Sender Address Sender’s E-mail account should be SMTP authentication type.
  • Page 99 Including Picture In general event, when sensor, MD, V-loss events are generated, the event information and channel video will be sent to e-mail together. But system event just send system event information. NOT USE This is the way of sending E-mail directly to receiver without SMTP server authentication E-Mail Address Input E-mail address of receiver.
  • Page 100: Motion Detection

    Installaction & User Manual FTP Upload Configure yes or no of image transmission to FTP server when Event occurs. If it is configured as On, Event image will be sent to FTP server. User ID Input ID information for FTP server Password Input Password for FTP server access.
  • Page 101 Channel All or certain channel. Sensitivity Sensitivity can be configured from min.1 to max 10. Area Select detection area. User can select all or certain channel. User Area When selecting per channel, it can be configured. 1 grid size is 22x15 and factory default value is All. If pushing user area, configuration window for detection area..
  • Page 102: Sensor

    Installaction & User Manual 6.5.4 Sensor This menu is to setup the existing sensor input and type of sensor. 16 input Sensor has 2 types, Normal Open(N.O.) and Normal Close(N.C.). 6.5.5 Preset In PTZ function, make configured preset work according to sensor input. Please, configure preset per PTZ.
  • Page 103: Recording Setup

    6.6 Recording setup There are 3 mode for recording – schedule recording, manual recording, event recording. Schedule recording records according to the configured schedule. And manual recording records via pushing “REC” button and event recording records when events are on. 6.6.1 Program setup Using [Program], adjust frame rate and quality and resolution and configure recording program for Manual&Event&Schedule.
  • Page 104 Installaction & User Manual Max R/F Max R/F shows the number of frame available according to the selected resolution. For instance, if it is set by 30fps at CIF, it means that the channel can record up to 30frame at CIF resolution.
  • Page 105: Manual/Schedule Recording Setup

    6.6.2 Manual/Schedule recording setup With the change of recording mode, manual recording or schedule recording can be at one’s choice. And their resolution , frame rate , quality will be in accordance with the program. 6.6.2.1 Manual Recording Only in manual & event recording, manual recording runs and when pressing [REC] button, recording starts.
  • Page 106 Installaction & User Manual Check and select each program default value and select one of 26 program from A to Z or Several programs. Below picture show program A. • INDEX : Schedule unit from 1 to 50 • Weekday : Set the day applicable •...
  • Page 107: Event Recording Setup

    that, from the largest INDEX in order. Edition  Select INDEX to edit and change weekday, program,time directly.  In case that INDEX 50 are all configured, select the time zone to change by mouse click and click the time again, previouse configuartion will be deleted and new configuration will be shown.
  • Page 108 Installaction & User Manual configure Event frame rate. 3. Set Event applying time. Event Time configuration Configure time for event recording and there are 3 mode – Always, no use, Timezone. In “Always”, event works all the time and in “Timezone”, works during configured time. Configuration of Timezone is similar with schedule configuration and can configure weekday,time for Event.
  • Page 109  In case of being configured by INDEX 50, click and select time to eidt and if clicking the time table again, previous configuartion will disappear and new configuration will be shown.
  • Page 110: Web Viewer

    Installaction & User Manual 7. Web Viewer WebViewer is Web application program loaded to monitor real-time image or to monitor the images recorded through Web browser to PC located remotely. WebViewer is divided into Login page and Monitor to do monitoring real-time images, Playback to replay recorded images.
  • Page 111: User Setup

    After input IP address that set to system, then WebViewer Login page will be connected. Input the set of User ID & Password, click ‘LOGIN’ to access. If didn’t change the password in Control Center, ID and Password will be admin/12345. ID can not be changed.
  • Page 112: Browser Available

    Installaction & User Manual Authority configuration is almost all the same in DVR and Control Center. But quick recording, backup, audio, yes or no of using channel are only possible in Control Center. Browser available WebViewer is optimized to Windows Internet Explorer 6.0 or higher in PC for smooth use. Webviewer Installer Login page provides manual installation program to use WebViewer function.
  • Page 113: Monitor

    Monitor When it is authorized with User ID & Password input at Login page, it moves to Monitor page. At Monitor page, monitor real time image of cameras connected to DVR, or it can control PTZ camera, Relay, and use Microphone function according to user’s authorization. Study introduction of each Monitor part and functions of the page.
  • Page 114: Move To Playback

    Installaction & User Manual After conversion to 1channel mode, double click on screen to return to previous division channels. At division screen, it can change screen location. If 3channel image moves to 6ch, drag 3ch image and drop on 6ch location so as to exchange between 3ch and 6ch image 7.5.2 Move to Playback...
  • Page 115: Relay Operation

    When it sensorsed, relevant sensor icon comes to Red, and indicates sensor number of video. 7.5.5 Relay operation It can On or Off Relay of the unit. Click the number button to activate Relay On, then the icon changes from Blue to Orange color. Disabled Relay button refers to do not support and relate to this unit.
  • Page 116: Video Recording & Save Saving

    Installaction & User Manual 7.5.8 Video Recording & Save Saving 7.5.8.1 Video Recording During monitoring, it can record max. 10 minutes of video by click Quick Recording button “ ”. During Quick Recording, recording time is indicated on video. During video recording, if click Quick Recording button “ ”...
  • Page 117 Pan, Tilt Control Mouse is on the image and click right button to pop-up menu for the selection or “PTZ” or button. Then it show Cross line on the middle of screen and click image to operate Pan, Tilt. At the middle click Left/Right direction to control Pan, and Click Up/Down direction to control Tilt.
  • Page 118: Using Audio

    Installaction & User Manual 7.5.10 Using Audio In case of Channel setup sync with Audio, press right mouse button on the image to activate pop-up menu to “Listen” or activate Audio listen button. First default is Mute. In case of listening Audio, select pop-up menu or button.
  • Page 119: Playback

    Playback This page is to playback recorded images, and user who has authority of ‘HDD’ among user ID or administrator can use this function. Playback that is made up 16 divisions can play the images by searching through colander by recording period and moving the period.
  • Page 120: Print

    Installaction & User Manual Save Image dialog box appears, then it can input message or select channel name, date, event data. Press ‘OK’ to open dialog box for the saving location, then save bmp file. 7.6.3 Print Select image with mouse for the channel to print image saved, and then click ‘Print’ button. Window comes to input Memo, and click ‘OK’...
  • Page 121: Web Monitor

    7.6.5 Web Monitor Click ‘Go’ button at top of page, and it can move Web monitor page. 7.6.6 Channel On/Off It is the same function like Channel On/Off function at Web Monitor. It is Channel On/Off button located on right of Page, and click On or Off page for wanted channel.
  • Page 122: Functional Function At The Button Of Monitor

    Installaction & User Manual 7.6.9 Functional function at the button of monitor ① Indicates playback range of recorded image. ② Press button as the time set at (5) so as to change the time zone to playback in forwarding and backwarding. ③...
  • Page 123: Java Viewer

    8 JAVA Viewer Java viewer is a web viewer to use in Java. Java should be installed in login screen to use Java viewer. After an installation of Java manually, select “Java” in below of Password window and login. Then single screen of video channel 1 is displayed Multi screen display, Event, Relay can be used in Java viewer.
  • Page 124: User Manual For Mobile Viewer

    Installaction & User Manual 9 User manual for Mobile Viewer Mobile viewer is viewer service to monitor video via mobile device. To access mobile viewer, user uses mobile device supporting Wi-Fi or smart phone or 3G. Log-In page Below picture is Mobile viewer log-in page. To access log-in page via mobile viewer, please, type the address like http://IP/mvmenu.html.
  • Page 125 For functions, please, refer to the below. [0] MENU : Move to Log In page [1] CH- : Move to the previous channel. [2] UP : Move to upside of Pan Tilt movement [3] WIDE : Zoom Out action [4]  : Move to left side of Pan Tile movement [6] ...
  • Page 126: Trouble Shooting

    Installaction & User Manual Trouble shooting 1. DVR booting failure 1. Check the power 2. Check Power cord 2. No video on monitor 3. Check monitor power 4. Check cable between DVR and monitor 5. Check monitor cable port 6. Check DVR power is off 7.
  • Page 127 9. If network is not working 25. Check if Network cable is connected 26. Check DVR IP 27. Check Computer IP 28. Ping Test 29. Check PC specification if Webview video is not shown. 10. The cases necessary to contact the shop 30.
  • Page 128: The Way To Check The Manufacturing Date

    Installaction & User Manual The way to check the manufacturing date It can be checked with its S/N(Serial Number).. S/N : Serial Number It means composite 12 digit number with product model name and production year,month, and week. It can be found on the attached label attached on the bottom of product or system info of configuration tool or system information 1 of DVR Func menu.
  • Page 129: Available Hdd

    Available HDD Please ask to seller about HDD available with DVR. Compatible CD/DVD list DVD-R manufacturer CD-R Manufacturer Mitsubishi(×16 recomended) Mitsubishi(×52 recomended) TDK(×16 recomended) TDK(×52 recomended) Imation(×16 recomended) Imation(×52 recomended) Sony(×16 recomended) Sony(×48 recomended) Specification Video input Video input standard NTSC or PAL auto detect Connectors 16ch analog video inputs BNC connector...
  • Page 130 Installaction & User Manual Search Type Time, Calender, Event, Thumbnail Block Playback 1day ~ 99days Event & Alarm Event source MD, Sensor, Text Event check schedule 24hrs / 7day Event Action Recording, Relay, E-mail, Buzzer, Pop-up, Warning Message, preset, FTP, SNS(Twitter) MD Area 22x15(NTSC), 22x18(PAL)
  • Page 131 Storage/Backup Storage Devices 4 internal SATA HDDs, 2 external eSATA I/F File System Proprietary file system, data-loss protection against power-failure Capacity Max 8TB Backup type multi-channel or single channel avi file Backup device internal CD/DVD or USB drive S.M.A.R.T. Temperature and Health Serial &...
  • Page 132: Product Dimention

    Installaction & User Manual Product Dimention...
  • Page 133 HUNT ELECTRONIC USA INC. 11790 Jersey Blvd. Rancho Cucamonga, CA 91730 Tel: (888)993-4868, (909)987-6999 Fax: (909)987-6997 techsupport@huntcctv.com www.huntcctv.com...

Table of Contents