Table of Contents
Advertisement
TABLE OF CONTENTS
Operator Protective Equipment . . . . . . . . .. . . . . . 2
Definition of Hazard Levels . . . . . . .. . . . . . . . . . . . . 3
Owner's Responsibility . . . . . . . . .. . . . . . . . . . . . . 3
Safety Instructions/Cautions . . . . . . . . . . . . . . . . . . 4
Receiving /Unpacking and Set Up . . .. . . . . . . . . . . . . . 5
Floor and Space Requirements . . . .. . . . . . . . . . . . . . 5
Anchoring the Balancer . . . . . . . . . . . . . . . . . . . . . . . 5
Parts Description . . . . . .. . . . . . . . . . . . . . . . . . . . . 6
Standard Accessories - Specifications / Features . . . . . . . . 7
Installation and Setup
Installation of the Display . . .. . . . . . . . . . . . . . . . . . . .. . 8-9
Mounting the Hood . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Threaded Shaft. . . .. . . . . . . . . . . . . .9-10
Installing the Outer Gauge Arm . . .. . . . . . . . . . . . . . . . . . .10
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Auto Hood Start: Enable / Disable . . .. . . . . . . . . . . . . 10
Activating the Outer Gauge Arm . . . . . . . . . . . . . . . . . . 11
Determining the Planes . . . . . . . . . . . . . . . . . 12
Control Panel and Display . . . . . . . . . . . . . . . . . 12
FUNCTION Button Operation . . . . . . . . . . . . . . . . . 13
GRAM / OUNCE Selection . . . . . . . . . . . . . . . 13
MM / INCH Selection . . . . . . . . . . . . . . . . . . . . . 13
Mounting Wheels . . . . . . . . . .. . . . . . . . . . . . . . .. 13-14
Front Cone Mounting . . . . . . . . . . . . . . . . . . . 14
Rear Cone Mounting . . . . . . . . . . . . . . . . . . . 14
Dual Cone Mounting . . . . . . . . . . . . . . . . . . . 14
Inputting Wheel Data Automatically. . . . . . . . . . . . . . . . 15
Inputting Wheel Offset & Wheel Diameter. . . .. . . . . . .15
Inputting Wheel Width . . . . . . . . . . . . . . . . . . .16
Inputting Wheel Data Manually . . . . . . . . . . . . . . . . . . .16
Spin Mode / Dynamic & ALU . . . . . . . . . . . . . . .17
Spin Mode / Static 1 & Static 2 . . . . . . . . . . . . . . . . . . .17
Spin Mode / ALU Exact Two Plane. . . . . . . . . . . . . 18
/ HID (Hidden Weight). . . . . . . . . . . . . 19
Re-checking The Balance . . . . . . . . . . . . . . . .20
STOP BUTTON / Identifying Remaining Weight . . . . . . 20
After Balance Vibration Problems . . . . . . . . . . . 20
Maintenance and Calibration
Troubleshooting Guide . . . . . . . . . . . . . . . . . 21
Weight Location Verification. . . . . . . . . . . . . . . . . . . 22
Outer Gauge Arm Calibration Procedure . . . . . . . . . . 22-23
Distance Slide Calibration Procedure . . . . . . . . . . . . . . 23
Dual-Plane Self-Calibration Procedure . . . . . . .. . . 23-24
Error Codes . . . . . . . . . . . . . . . . . . . 25
Parts Breakdown . . . . . . . . . . . . . . . 26-34
Wheel Weights Order Form. . . . . . . . . . . . . . . . . . . . 35
Failure to follow danger, warning, and caution instructions
may lead to serious personal injury or death to operator or
bystander or damage to property.
Do not operate this machine until you read and understand
all the dangers, warnings, and cautions in this manual.
For additional copies
or further information, contact:
BendPak Inc. / Ranger Products
1645 Lemonwood Dr.
Santa Paula, CA. 93060
1-805-933-9970
www.rangerproducts.com
OPERATOR PROTECTIVE EQUIPMENT
Personal protective equipment helps make tire and wheel
service safer. However, equipment does not take the place
of safe operating practices. Always wear
durable work clothing during tire service
activity. Shop aprons or shop coats may also
be worn, however, loose fitting
clothing should be avoided. Tight-fitting
leather gloves are recommended to protect operator's
hands when handling worn tires and wheels. Sturdy
leather work shoes with steel toes and oil resistant soles
should be used by tire service personnel to help prevent
injury in typical shop activities. Eye protection is
essential during tire service activity. Safety glasses with
side shields, goggles, or face shields are acceptable. Back
belts provide support during lifting activities and are also
helpful in providing operator protection. Consideration
should also be given to the use of hearing protection if
tire and wheel service activity is performed in an enclosed
area, or if noise levels are high.
THIS SYMBOL POINTS OUT IMPORTANT
SAFETY INSTRUCTIONS WHICH IF NOT
FOLLOWED COULD ENDANGER THE
PERSONAL SAFETY AND/OR PROPERTY
OF YOURSELF AND OTHERS AND CAN CAUSE
PERSONAL INJURY OR DEATH. READ AND
FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
2
!
Hide quick links:
Advertisement
Table of Contents
