Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for GardenMaster GM43PBC
- Page 1 SAFETY AND OPERATING MANUAL 43cc PETROL BRUSH CUTTER GM43PBC...
-
Page 2: Safety Instructions
cutter may result in serious personal injury. WARNING: Read all instructions! Failure to follow all instructions listed below may result in, fire and/or serious injury. 7. Keep away from cutting blade This product should not be operated by those Even after the engine has stopped, the cutting who are unfamiliar with the manual. -
Page 3: Safety Inspection
carburetor adjustment section. b) Use only an approved container for fuel storage and mixing. 3) Always switch off the engine and allow it to c) Never mix petrol/ oil in the machine fuel tank. cool before making any adjustments 4) Make sure all guards, straps, debris shield d) Do not smoke, and avoid sparks and flames near fuel or unit. -
Page 4: Maintenance Inspection
2. Replace any damaged parts. the area while refueling. 3. Check that all fasteners, guards and handles 11. Always mop up fuel spillage as quickly as etc are in place and secure. Tighten as possible. Change your clothes if you spill fuel necessary. - Page 5 SYMBOLS Read the instruction manual Warning Wear gloves Wear foot protection The distance between the machine and bystanders shall be at least 15m Beware of thrown objects WARNING: Appropriate ear, eye and head protection must be worn. Beware of blade thrust RCM approval mark...
- Page 6 12 14...
-
Page 7: Component List
COMPONENT LIST Cutting blade Plastic safety guard – USE WITH BRUSHCUTTER/ GRASS TRIMMER Cutting head / Spool Clamp Knob U handle Throttle trigger Start / Stop ignition switch Locking knob On/off switch 10. Choke lever 11. Primer bulb 12. Spark plug 13. -
Page 8: Technical Data
TECHNICAL DATA 2-Stroke Engine displacement 43cc Engine power 1400kW Engine maximum speed (No-load) 9500/min(with brush cutter) Engine idling speed 3000+/-300/min Clutch engagement speed Min 4200/min Max cutting diameter (Grass trimmer) Ø44cm Max cutting diameter (Brushcutter) Ø25.5cm Line diameter Ø2.4mm Line length Fuel consumption (ISO 8893) at maximum engine power ≤0.95kg/h Specific consumption (ISO 8893) at maximum engine power... -
Page 9: Intended Use
NOTE: Before using the brushcutter / grass trimmer, read the instruction book carefully and make sure you FULLY understand them. INTENDED USE This product is intended for cutting grass and small bushes. Fig.A1 ASSEMBLY ASSEMBLING THE U-HANDLE 1. Loosen the 4 bolts on the upper clamp (See Fig A1). 2. - Page 10 Fig.A4 ASSEMBLING THE PLASTIC SAFETY GUARD (See Fig. B1, B2) Attach the safety guard to the bracket and align the holes, then tighten the 4 screws using the supplied screwdriver and spanner. When fix the safety guard on position(a), the cutting diameter is 420mm;...
-
Page 11: Assembling The Cutting Blade
Fig.D1 ATTENTION left thread - to tighten turn counter clockwise, to loosen turn clockwise (See Fig. D2). ASSEMBLING THE CUTTING BLADE ATTENTION: Spindle is provided with a left hand thread – to loosen turn clockwise. WARNING! To prevent injury wear thick safety gloves and use correct assembly tools and equipment. -
Page 12: Installing And Adjusting The Shoulder Harness
Fig.E2 Filling the tank 1) Rest the tool on the ground with the fuel tank cap (m) facing up (See Fig. F1). Clean surface around fuel cap to prevent contamination. 2) CAUTION! Loosen the fuel cap slowly to release pressure and prevent fuel from escaping around the cap. 3) Carefully pour fuel mixture into the tank. -
Page 13: Safe Operating Precautions
Fig.G2 SAFE OPERATING PRECAUTIONS For your safety, avoid starting or operating the engine in enclosed areas, such as a garage. Your engines exhaust contains poisonous carbon monoxide gas, which can Staring posture collect rapidly in an enclosed area and cause illness or death. -
Page 14: Starting Warm Engine
Fig.H3 Pump primer bulb (12) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 4) Starter pull cord. Place the unit on a flat, clear area. With your left hand, hold the frame tube just ahead of the engine. -
Page 15: The Importance Of Maintenance
Fig.H5 5. BUMP FEED CUTTING LINE HEAD NOTE: A protective cover is fitted to the line cutoff blade. Remove this protective cover before operating. (See Fig. I) As the end of the line wears away, more line must be released from the cutting line head. Your trimmer is factory fitted with a semiautomatic (bump feed) cutting line head. -
Page 16: Spark Plug
Fig.J2 2) Check the filter to be sure it is clean and in good condition. If the filter is dirty, clean the air filter in warm soapy water, rinse, and allow to dry thoroughly. Replace the filter if it is damaged. Reinstall the filter and air filter cover. - Page 17 Fig.K3 1) Clean any mud, dirt, debris, etc, from the area around the trimmer head; otherwise, it will make it more difficult to service. 2) Remove the spool from spindle. Then remove the old nylon line. 3) Measure approximately 2 meters of line, and then thread one end through the hole on the spool.
-
Page 18: Carburetor Adjustment
Fig.L5 9. CARBURETOR ADJUSTMENT WARNING! Incorrect adjustment may cause damage to your unit. If the engine does not run well after adjusting the carburetor, please contact the Helpline for advice. The idle adjustment screw (n) (See Fig. M) is used to adjust the engine rotation speed. -
Page 19: Troubleshooting
TROUBLESHOOTING If you experience problems, check the following; Symptom Cause Solution Start/Stop switch “O” Move to position “I”. Refer to section “Operation” Fig. H2. Choke not OFF(cold engine) Move choke to the OFF position. Refer to section “Starting the machine.” Out of Fuel. -
Page 20: Warranty
WARRANTY This product is warranted for a 2-year period for home domestic use from the date of the original purchase. If found to be defective in materials or workmanship, the tool or the offending faulty component will be replaced free of charge with another of the same item.