ABB CM30 User Manual page 2

Basic Level
Refer to Section 6, page 18
Menu
Basic
Exit Select
Loop 1 (2) Setpoints
Local Setpoint 1 (4)
RSP Ratio
RSP Bias
Ramp Mode
Ramp Rate

Loop 1 (2) Control
On/Off
Mode
Autotune
PID
FeedForward

Loop 1 (2) Mot Valve
Ratio
Bias
Deadband
Travel Time
Loop 1 (2) Time Prop 
Cycle Time 1 (2)

Alarm 1 (8)
Trip
Refer to Section 7.5, page 47 Refer to Section 7.6, page 49
Menu Menu
Process Alarm
Exit Select Exit
Alarm 1 (8)
Type
Tag
Source
Trip
Hysteresis
Time Hysteresis
Display Enable
Acknowledge Source
Enable Source
*When in Advanced Level (configuration mode), press and hold the
**Enabled for CM30 and CM50 only
*Advanced Level...
Refer to Section 7.1, page 24
Menu
Device Setup
Exit Select
Language
Initial Setup

App. Template
Loop 1 (2) Output Type Operator Templates
Loop 1 (2) Split O/P
Instrument Tag
Operator Functions
Loop 1 (2) Tag
Mains Freq.
Config Action
Custom Template
Reset to Defaults
Security Setup
Basic Password
Advanced Password

Reset Passwords
Chart View
Custom Config

Off 
Settings
Loop 1 (2) PV
Loop 1 (2) Split O/P
Loop 1 (2) Valve O/P
Loop 1 (2) Valve FB
Loop 1 (2) TP OP1 (2)
Loop 1 (2) RSP
Refer to Section 7.7, page 53
Menu
Totalizer Functions
Select Exit
Totalizer 1 (2) Logic Equations
Mode Equation Number
Source Operand 1
Count Direction Invert 1
Units Operator 1
Count Rate
Cutoff Math Blocks
Stop Go Source Math Block Number
Total DPs Block Type
Preset Count Eng. DPs
Predet Count Eng. Low
Intermed'te Count Eng. High
Wrap Enable Eng. Units
Reset Source Fault Action
Reset Days 
Reset Hour Linearizer 1 (2)
key to return to the standard Operator page – see Fig. 3.1, page 5.
Refer to Section 7.2, page 26
Menu
Display
Exit Select
Date & Time
Date Format
Time & Date
Page 1 Template
Daylight Saving

DS Start Time
DS Start Occur
Autoscroll
DS End Occur
Soft Key Function
DS Start Day
Auto Manual Enable
DS End Day
Local Remote Enable
DS Start Month
Alarm Ack. Enable
DS End Month
Totalizer Stop/Go

Totalizer Reset
Customise Pages
SP Adjust Enable
Page Number
Template Type
Titlebar Tag
Channel 1
Parameters
Sample Rate
Bargraphs
Icons
Page Colors
Brightness
Contrast**
Refer to Section 7.8, page 58
Menu
Communication
Select Exit
Delay Timer 1 (2) Refer to IM/CM/C-EN for
Source parameter details.
Delay Time
On Time
Real Time Alarms
Real Time Alarm 1 (2)
Monday (to Sunday)
Refer to Section 7.3, page 32
Menu
Input/Output
Exit Select
Loop 1 (2) Setpoints
Analog Inputs
Low Limit
Anlg Input 1 (4)
High Limit
No. of Local SP's
Analog Outputs
Local Setpoint 1 (4)
Analog Output 1 (2)
Track Mode
Digital I/O  RSP Ratio
RSP Bias
Digital IO 1 (6)
RSP Fault Action
Relays
Default Setpoint
Ramp Mode
Relay 1 (4)
Ramp Rate
Select Sources
Loop 1 (2) Control
Control Type
Control Action
On/Off Hysteresis
Autotune
PID
Gain Scheduling
FeedForward
Adaptive Control
Misc.
Refer to Section 7.9, page 59
Menu
Diagnostics
Select Exit Select
Diagnostic History
Source Analysis
Analog Source
Digital Source
Invalid Sources
Refer to Section 7.4, page 36
Menu
Control
Exit Select
Loop 1 (2) Output
Limits
Failure Actions
A/M Select Sources
Slew Rate
Tracking
Loop 1 (2) Split O/P
Min Input 1 (2)
Min OP 1 (2)
Max Input 1 (2)
Max OP 1 (2)
Loop 1 (2) Valve
Ratio
Bias
Deadband
Travel time
Loop 1 (2) Time Prop
Cycle Time 1 (2)
Refer to Section 7.10, page 63
Menu
Device Info
Exit Select
Instrument Type
I/O Build
No. Analog Inputs
No. Analog Outputs
No. Relays
No. Digital I/O
Functionality
Serial No.
Hardware Revision
Software Revision