Solution Ultima 862 Quick Reference Guide ISSUE 1.70...
Page 2
Notice of Liability While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty Limited nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book.
Step To Next Location Step Back One Location Program New Data Into Location Data + * (Data = 0 – 15) Jump To Another Location Location No. + # Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
Copy Panel Memory To Programming Key Copy Programming Key To Panel Memory Erase Programming Key Default System For Domestic Dialling Format Enable/Disable Automatic Stepping Of Locations When Programming Display Software Version (Hand Held Programmer Required) SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Page 5
# key. heard (Only if no alarm). Press the * key to delete the RF device. Enter your code followed by the # key. [eg. 2580 + #]. Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
Page 6
Enter the New Code followed by the # key. Day Alarm – Toggle On/Off Press and hold the 4 key until two beeps are heard. Day alarm will toggle on or off. SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Modem Call (Alarm Link) Press and hold the 6 key until two beeps are heard. Latching Outputs (Reset) Press and hold the 7 key until two beeps are heard. Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
2 = Sound Alarm When System Is Armed 4 = Sound Alarm When System Is Disarmed Note: Option 2 & 4 Must Be Used In Conjunction With Option 1 (Eg. Program a 1, 3, 5 or 7) SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Options 2 Code Options Location Zone #08 (Default = 24 Hr Tamper) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler Type Count Count Time Options 1 Options 2 Code Options SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Page 11
Momentary Arm In AWAY Mode Momentary Disarm From AWAY Mode Or STAY Mode Momentary Arm and Disarm In STAY Mode Momentary Arm In STAY Mode Momentary Disarm From STAY Mode Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
1 = Report To Receiver 1 2 = Report To Receiver 2 4 = Report To Both Receiver 1 & Receiver 2 8 = Report To Receiver 2 Only If Receiver 1 Fails SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
1 = Report To Receiver 1 2 = Report To Receiver 2 4 = Report To Both Receiver 1 & Receiver 2 8 = Report To Receiver 2 Only If Receiver 1 Fails Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
Any Areas Disarmed (Solution 880 Only) 2 15 Communications Fail After 3 Attempts Area 1 Codepad Data Terminal (Solution 880 Only) Communications Fail Area 2 Codepad Data Terminal (Solution 880 Only) SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Page 15
‘OFF’ time. The ‘OFF’ time is the time base x the multiplier (eg. If you want the output to pulse one (1) second ‘ON’ and five (5) seconds ‘OFF’, you would program time base as one (1) and the multiplier as five (5)). SOL ULTIMA 862 QUICK REF GUIDE...
1 = Codepad Panic To Be Silent 2 = Codepad Fire To Be Silent 4 = Codepad Medical To Be Silent 8 = Access Denied (Code Retries) To Be Silent SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Location 907 = Month Of The Year (Tens Digit) 905 906 907 908 909 910 Location 908 = Month Of The Year (Units Digit) Location 909 = Current Year (Tens Digit) Location 910 = Current Year (Units Digit) SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Page 19
RF signal from a remote RF device. RF Keyfob Operations For Solution Ultima Series Control Panels Figure 2: RF3332 - 2 Button RF Keyfob Figure 3: RF3332 - 2 Button RF Keyfob Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
(Location 266 = 14) Connections For Split EOL Resistors Using N/O Contacts Figure 6: Split EOL Wiring Diagrams Using N/O Contacts Wiring Diagram For Keyswitch Zone Figure 7: Wiring Diagram For Keyswitch Zone SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...
Quick Reference Guide Solution Ultima 862 Wiring Diagram Figure 8: Solution Ultima Series Wiring Diagram Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D...
Page 22
Quick Reference Guide Solution Ultima 862 Component Overlay Figure 9: Solution Ultima Series Component Overlay SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited...