Huawei SmartAX MA5603T Configuration Manual
  1. Manuals
  2. Brands
  3. Huawei Manuals
  4. Gateway
  5. SmartAX MA5603T
  6. Configuration manual

Huawei SmartAX MA5603T Configuration Manual

Access module
Hide thumbs Also See for SmartAX MA5603T:
1
2
3
4
5
Table Of Contents
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
Table of Contents

Advertisement

Quick Links

SmartAX MA5600T/MA5603T/MA5608T Multi-
service Access Module
V800R015C00
Commissioning and Configuration
Guide
Issue
01
Date
2014-04-30
HUAWEI TECHNOLOGIES CO., LTD.

Advertisement

Table of Contents
loading

Related Manuals for Huawei SmartAX MA5603T

Summary of Contents for Huawei SmartAX MA5603T

  • Page 1 SmartAX MA5600T/MA5603T/MA5608T Multi- service Access Module V800R015C00 Commissioning and Configuration Guide Issue Date 2014-04-30 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 2 All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope.

  • Page 3: About This Document

    TIP indicates a tip that may help you solve a problem or save time. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 4 Updates in Issue 01 (2014-04-30) This is the first release. Compared with issue 02 (2013-12-18) of V800R013C10, the document is updated as follows: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 5 Configuration (MA5633 Working as a Standalone NE): IPv6. 16.3.1.8 Configuring a Service Channel Between an OLT and a D-CMTS 16.4.1.8 Configuring a Management Channel Between an OLT and a D-CMTS Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 6: Table Of Contents

    1.3.7 Loading a Configuration Script..........................63 1.3.8 Changing the System Name............................64 1.3.9 Configuring the System Time............................65 1.3.10 Configuring a System User............................67 1.3.10.1 Adding a System User............................67 1.3.10.2 Modifying the System User Attributes.........................69 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 7 1.4.5 Commissioning the Interconnection with the SIP Interface..................171 1.4.6 Commissioning the Management Channel Between the OLT and the GPON MDU..........174 1.4.7 Commissioning the Management Channel Between the OLT and the GPON ONT..........179 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 8 3.1 Example: Configuring the xDSL Internet Access Service..................253 3.1.1 Example: Configuring the xDSL Internet Access Service Through PPPoE Dialup..........253 3.1.2 Example: Configuring the xDSL IPoE Internet Access Service................260 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 9 4.4 Configuration Example of TDM SHDSL for Transparently Transmitting the Narrowband Data Private Line Service ......................................430 4.5 Configuration Example of the Private Line Service Leasing E1 Timeslots...............433 Issue 01 (2014-04-30) Huawei Proprietary and Confidential viii Copyright © Huawei Technologies Co., Ltd.
  • Page 10 9.7 GPON Access: Configuring FTTH Service.......................577 9.7.1 Bridging+Voice ONT Network Scenario........................578 9.7.1.1 Service Requirements and Application Scenario....................578 9.7.1.2 Configuration Process............................579 9.7.1.3 Adding an ONT to an OLT...........................582 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 11 10.3 Networking Scenarios and Hardware Configurations (GPON)................727 10.4 Reference of GPON ONU Capability Sets.......................730 10.5 Principle of FTTD Data Plan............................731 10.5.1 Data Plan Principles for IP Addresses........................731 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 12 11.2 Principle of FTTB and FTTC Data Plan........................833 11.2.1 Principle of Device Management Data Plan......................833 11.2.2 Principle of QoS Data Plan............................835 11.2.3 Principle of Internet Access Service Data Plan.....................837 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 13 11.3.3.8 Configuring the Internet Access Service (VDSL2 Access, on the ONU)............938 11.3.3.9 (Optional) Configuring Vectoring........................941 11.3.3.10 Configuring H.248 Voice Service (on the ONU).....................952 11.3.3.11 Configuring SIP Voice Service (on the ONU)....................956 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 14 11.4.2.4 Adding GE Remote Extended Subracks......................1048 11.4.2.5 Configuring VDSL2 User Ports........................1049 11.4.2.6 Configuring VDSL2 Service Flows.........................1050 11.4.2.7 (Optional) Configuring Vectoring........................1053 11.4.2.8 Configuring Link Aggregation, Congestion Control, and Security Policies............1059 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xiii Copyright © Huawei Technologies Co., Ltd.
  • Page 15 12.4.1.6 Configuring the H.248-based Voice Service (Through the CLI)..............1159 12.4.1.7 Configuring the SIP-based Voice Service (on a Web Page)................1162 12.4.1.8 Configuring the SIP-based Voice Service (Through the CLI).................1169 12.4.1.9 Configuring the BTV Service...........................1174 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 16 13.3 Configuring Enterprise Access Service (GPON)....................1268 13.3.1 Layer 2 Interoperation Service Between Enterprise Branches................1269 13.3.1.1 Service Requirement and Application Scenario....................1269 13.3.1.2 Configuration Process............................1270 13.3.1.3 Adding ONUs to OLT............................1271 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 17 13.3.5.2 Configuration Process............................1328 13.3.5.3 Adding ONUs to OLT............................1330 13.3.5.4 Configuring Management Service Ports on OLT and ONUs................1332 13.3.5.5 Configuring SAToP Connections and Service Ports..................1333 13.3.5.6 Configuring ONU SAToP Connections......................1336 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 18 14.4.1.2 Configuration Process............................1400 14.4.1.3 Adding ONUs to OLT............................1401 14.4.1.4 Configuring Management Service Ports on OLT and ONUs................1404 14.4.1.5 Configuring TDM E1 Connections........................1405 14.4.1.6 Configuring Clock Synchronization.........................1406 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xvii Copyright © Huawei Technologies Co., Ltd.
  • Page 19 14.4.5.3 Adding ONUs to OLT-A and Configuring the Management Service Port............1466 14.4.5.4 Configuring the TDM Connection and TDM PW....................1470 14.4.5.5 Configuring Clock Synchronization.........................1473 14.4.5.6 Configuring E2E Reliability..........................1474 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xviii Copyright © Huawei Technologies Co., Ltd.
  • Page 20 15.1.2 Networking Scenarios and Hardware Configurations (GPON)................1522 15.1.3 Networking Scenarios and Hardware Configurations (GE)................1523 15.2 Data Plan Principles for D-CMTS Services......................1524 15.2.1 Frequency Spectrum Management........................1524 15.2.2 Device Management............................1526 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 21 15.4.1.4 Configuring a Route............................1598 15.4.1.5 Configuring DHCP Relay (IPv6)........................1600 15.4.1.6 Configuring a Route (IPv6)..........................1603 15.4.1.7 Adding a Remote Extended Frame to an OLT....................1605 15.4.1.8 Configuring RF Port Parameters........................1607 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 22 16.3 Service Configuration on a D-CMTS That Works in GE Access Mode on a Layer 3 Network......1679 16.3.1 Home Service Networking..........................1679 16.3.1.1 Service Requirements and Usage Scenario......................1679 16.3.1.2 Configuration Process............................1680 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 23 16.4.1.11 Configuring the HSI Service on an MA5633....................1755 16.4.1.12 Configuring the DOCSIS VoD Service on an MA5633.................1756 16.4.1.13 Configuring the EQAM VoD Service on an MA5633...................1757 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xxii Copyright © Huawei Technologies Co., Ltd.
  • Page 24 19.3 Configuring IPv6 Services in the FTTB/C (No HGWs) Scenario.................1884 19.3.1 Application Scenarios............................1884 19.3.2 Data Planning..............................1885 19.3.3 Configuration Procedure............................1887 19.3.4 Configuration Example............................1889 19.4 Configuring IPv6 Services in the FTTB+HGW Scenario..................1897 19.4.1 Application Scenario............................1897 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xxiii Copyright © Huawei Technologies Co., Ltd.
  • Page 25 19.5.3 Configuration Procedure............................1919 19.5.4 Configuration Example............................1920 19.6 Configuring IPv6 Services in the FTTH (Gateway ONT) Scenario...............1934 19.6.1 Application Scenarios............................1934 19.6.2 Data Plan................................1935 19.6.3 Configuration Procedure............................1938 19.6.4 Configuration Example............................1939 Issue 01 (2014-04-30) Huawei Proprietary and Confidential xxiv Copyright © Huawei Technologies Co., Ltd.

  • Page 26: Commissioning

    The following recommended commissioning tasks and sequences are for reference only. Different offices have different conditions; therefore, it is recommended that customers, with the assistance of Huawei engineers, modify commissioning tasks according to actual requirements. 1.4 Interconnection Commissioning The MA5600T/MA5603T/MA5608T provides multiple interfaces for interconnection.

  • Page 27: Commissioning Introduction

    The commissioning items in the commissioning procedure are described as follows: Commissioning Preparations This topic describes the hardware, software, and tool preparations for the commissioning. Stand-Alone Commissioning Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 28: Commissioning Preparations

    The connectors are tight and firm. l The cable jacket is intact. l Cable labels are legible. l Cables are bundled properly. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 29: Preparing Software

    TFTP, SFTP, and FTP tools: used for loading software. They can be downloaded from http:// support.huawei.com. You are advised to use SFTP tools. l Client software key generator Puttygen.exe, client software key convertor sshkey.exe and SSH client software putty.exe: used for logging in to the MA5600T/MA5603T/ MA5608T through the SSH.

  • Page 30: Preparing Tools

    One multimeter Used to measure the voltage, resistance and current intensity during the power commissioning. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 31: Planning Data

    For details about the default settings of DIP switches on the fan monitoring board on the MA5600T, see 1.3.1.2 Checking the Settings of DIP Switches on the Fan Monitoring Board. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 32: Stand-Alone Commissioning

    The following recommended commissioning tasks and sequences are for reference only. Different offices have different conditions; therefore, it is recommended that customers, with the assistance of Huawei engineers, modify commissioning tasks according to actual requirements. 1.3.1 Checking the Settings of DIP Switches This topic describes how to check the settings of the DIP switches on the environment monitoring board (ESC board) and the fan monitoring board.
  • Page 33 S6-1 to S6-5 are used to set the sub-node IDs of the H801ESC board. Table 1-7 lists the mapping between S6-1 to S6-5 and sub-node IDs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 34 00001(1) 00010(2) 00011(3) 00100(4) 00101(5) 00110(6) 00111(7) 01000(8) 01001(9) 01010(10) 01011(11) 01100(12) 01101(13) 01110(14) 01111(15) (default) 10000(16) 10001(17) 10010(18) 10011(19) 10100(20) 10101(21) 10110(22) 10111(23) 11000(24) 11001(25) 11010(26) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 35 Figure 1-3 Removing the H801ESC board Step 3 Hold the ejector lever of the front panel and remove the H801ESC board from the PDU, as shown in (2) of Figure 1-3. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 36: Checking The Settings Of Dip Switches On The Fan Monitoring Board

    Do not change the DIP switch setting on the fan monitoring board of the MA5603T. The DIP switches on the fan monitoring board of the MA5608T does not support the DIP switch. The device must be powered off. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 37 Used to set the baud rate of the communication between the fan tray and the control board. l ON: The baud rate is 19200 bit/s (default). l OFF: The baud rate is 9600 bit/s. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 38 Table 1-10 Settings of SW2-5 and SW2-6 SW2-6 SW2-5 Quantity of Fans Remarks The unique and default setting of the 19-inch fan tray The unique and default setting of the ETSI fan tray Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 39 If the temperature is higher than 50°C, policy 3. the fans rotate at full speed. Therefo re, only this setting can be adopted. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 40 Step 1 Loosen the screws on the front panel of the fan tray anticlockwise by using the Phillips screwdriver, as shown in (1) of Figure 1-7. Figure 1-7 Removing/Inserting the fan tray Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 41: Powering On The Device

    Turn on the output control switch of the AC PDU. Turn on the output control switch of the power system. Turn on the output control switch of the DC PDU. ----End Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 42: Commissioning The Power Supply System

    When one power board is faulty, the other power board provides power for all the service boards in the shelf. When checking the power supply of the power board, pay attention to the following points: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 43: Configuring The Maintenance Terminal

    Properties. The Local Area Connection Properties dialog box is displayed. Click the General tab, and then select Internet Protocol (TCP/IP) in Components checked are used by this connection, as shown in the following figure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 44 Click Properties to display the Internet Protocol (TCP/IP) Properties dialog box. Click General, and then select Use the following IP address: to configure the IP address and the subnet mask, as shown in the following figure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 45: Logging In To The System

    MA5603T/MA5608T through the maintenance terminal. The following describes three login modes, namely, local serial port mode, telnet mode, and SSH mode. SSH with high priority is recommended. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 46: Login Through The Local Serial Port

    Figure 1-10 Logging in to the MA5600T/MA5603T/MA5608T through the local serial port RS-232 cable Serial port Access node Flowchart Figure 1-11 shows the flowchart for logging in to the system through the local serial port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 47 Click Start. Choose All Programs > Accessories > Communications > Hyper Terminal to display the Connection Description dialog box. Input the connection name, and click OK, as shown in the following figure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 48 COM1 or COM2 (here, use COM2 as an example), and click OK, as shown in the following figure. Set the HyperTerminal communication parameters. For details, see the following figure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 49 Choose File > Properties on the HyperTerminal interface. In the dialog box that is displayed, click the Settings tab, and set Emulation to VT100 or Auto Detect, as shown in the following figure. It is Auto Detect by default. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 50 Click ASCII Setup. In the dialog box that is displayed, set line delay to 200 and Character delay to 200, and then click OK, as shown in the following figure. By default, Line delay is 0, and Character delay is 0. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 51: Login Through Telnet (Outband Management)

    ETH port. NOTE The default IP address of the maintenance Ethernet port (ETH port on the control board) is 10.11.104.2, and the subnet mask is 255.255.255.0. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 52 MA5608T to manage the MA5600T/MA5603T/MA5608T in the outband management mode. In such a condition, if the MA5600T/MA5603T/MA5608T uses SCUL/SCUB control board, and the peer device does not support the cable autosensing function, a crossover cable must be used. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 53 Ethernet port (ETH port on the control board) is 10.11.104.2, and the subnet mask is 255.255.255.0. Maintenance terminal IP address: 10.10.1.10/24 Router port connecting to the MA5600T/ IP address: 10.50.1.1/24 MA5603T/MA5608T Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 54 Step 3 Add a route for the outband management. If the network environment is set up as shown in Figure 1-13, you need not add a route. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 55 When the login is successful, the system displays the following information: >>User name:root >>User password:admin Huawei Integrated Access SoftwareMA5600T/MA5603T/MA5608T. Copyright(C) Huawei Technologies Co., Ltd. 2002-2012. All rights reserved. ----------------------------------------------------------------------------- User last login information: ----------------------------------------------------------------------------- Access Type : Telnet IP-Address : 10.10.10.122...
  • Page 56 After logging in to the system, you can maintain and manage the MA5600T/MA5603T/ MA5608T. NOTE To improve the system security, please modify your password after first login. You can run the terminal user password command to modify your password. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 57: Login Through Telnet (Inband Management)

    LAN, and Figure 1-19 shows an example network for inband management through telnet in a WAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 58 Table 1-14 Data plan for the inband management through telnet in a LAN Item Data Upstream port of the MA5600T/MA5603T/ l VLAN ID: 30 MA5608T l Port: 0/19/0 l IP address: 10.50.1.10/24 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 59 Figure 1-20 shows the flowchart for logging in to the MA5600T/MA5603T/MA5608T through telnet (inband management). Figure 1-20 Flowchart for logging in to the MA5600T/MA5603T/MA5608T through telnet (inband management) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 60 10.50.1.10" in the Open field as shown in Figure 1-21 (considering the Windows OS as an example), and click OK. Then, the telnet dialog box is displayed. Figure 1-21 Running the telnet application Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 61 When the login is successful, the system displays the following information: >>User name:root >>User password:admin Huawei Integrated Access SoftwareMA5600T/MA5603T/MA5608T. Copyright(C) Huawei Technologies Co., Ltd. 2002-2012. All rights reserved. ----------------------------------------------------------------------------- User last login information: ----------------------------------------------------------------------------- Access Type : Telnet IP-Address : 10.10.10.122...
  • Page 62 Figure 1-22 config Login enable User mode Global config mode Interface/config mode Privilege mode interface huawei(config-if-...) huawei> huawei# huawei(config)# quit quit quit disable return Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 63: Login Through Ssh (Outband Management)

    SSH in a LAN, and Figure 1-24 shows an example network for outband management through SSH in a WAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 64 Router Access node Data Plan Table 1-16 Table 1-17 provide the data plan for the outband management through SSH in a LAN and in a WAN respectively. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 65 IP address: 10.10.1.10/24 Router port connecting to the MA5600T/ IP address: 10.50.1.1/24 MA5603T/MA5608T Flowchart Figure 1-25 shows the flowchart for logging in to the MA5600T/MA5603T/MA5608T through SSH. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 66 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 1 Commissioning Figure 1-25 Flowchart for logging in to the MA5600T/MA5603T/MA5608T through SSH (Outband Management) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 67 The range of public key size is (512 ~ 2048). NOTES: If the key modulus is greater than 512, It will take a few minutes. Input the bits in the modulus[default = 512]: Generating keys... Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 68 ...++++++++ Step 6 Set the SSH user authentication mode. Run the ssh user huawei authentication-type rsa command to choose the authentication mode of the SSH user. There are four authentication modes for SSH users, as shown in the following. In this topic, authentication mode rsa is considered as an example.
  • Page 69 Click Save public key and Save private key to save the public key and the private key respectively after they are generated, as shown in Figure 1-28. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 70 Open sshkey.exe, click Browse, and choose the public key file saved in the preceding step. Then, click Convert to change the client public key to the RSA public key, as shown in Figure 1-29. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 71 NOTE: The number of the bits of public key must be between 769 and 2048. huawei(config-rsa-public-key)#public-key-code begin Enter "RSA key code" view, return last view with "public-key-code end". huawei(config-rsa-key-code)#30818702 81810098 933744B6 7C864EC7 A86A84CC 198BAC1 huawei(config-rsa-key-code)#D32834F7 365CFD17 E7FE4041 3266E416 710D13ED 22BD4D5 huawei(config-rsa-key-code)#DF0C3E46 A995CC61 DC4CB179 F6888B8C 3F8A3085 51EDB5C...
  • Page 72 Step 9 Assign the public key to the SSH user. Run the ssh user assign rsa-key command to assign the RSA public key to the SSH user. huawei(config)#ssh user huawei assign rsa-key key Step 10 Log in to the system.
  • Page 73 Figure 1-32. Input the user name to log in to the system (here, the user name is huawei). Figure 1-32 Interface for logging in to the system using the SSH client software ----End...

  • Page 74: Login Through Ssh (Inband Management)

    – Configure the IP address of the PC that is used for logging in to the MA5600T/ MA5603T/MA5608T. This IP address is on the same subnet as the IP address of the Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 75 Figure 1-34 Example network for inband management through SSH in a LAN Access node Figure 1-35 Example network for inband management through SSH in a WAN Router Access node Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 76 User name/Password: huawei/test01 l Authority: Operator l Permitted reenter number: 4 Maintenance terminal IP address: 10.10.1.10/24 Router port connecting to the MA5600T/ IP address: 10.50.1.1/24 MA5603T/MA5608T Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 77 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 1 Commissioning Flowchart Figure 1-36 shows the flowchart for logging in to the MA5600T/MA5603T/MA5608T through SSH. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 78 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 1 Commissioning Figure 1-36 Flowchart for logging in to the MA5600T/MA5603T/MA5608T through SSH (Inband Management) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 79 Adding user succeeds Repeat this operation? (y/n)[n]:n Step 5 Create the local RSA key pair. Run the rsa local-key-pair create command to create the local RSA key pair. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 80 ...++++++++ Step 6 Set the SSH user authentication mode. Run the ssh user huawei authentication-type rsa command to choose the authentication mode of the SSH user. There are four authentication modes for SSH users, as shown in the following. In this topic, authentication mode rsa is considered as an example.
  • Page 81 Select SSH-2 RSA as the key type under Parameters, click Generate, and move the cursor according to the prompt on the interface to generate the client key, as shown in Figure 1-38. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 82 Click Save public key and Save private key to save the public key and the private key respectively after they are generated, as shown in Figure 1-39. Figure 1-39 Save the public key and the private key Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 83 NOTE: The number of the bits of public key must be between 769 and 2048. huawei(config-rsa-public-key)#public-key-code begin Enter "RSA key code" view, return last view with "public-key-code end". huawei(config-rsa-key-code)#30818702 81810098 933744B6 7C864EC7 A86A84CC 198BAC1 huawei(config-rsa-key-code)#D32834F7 365CFD17 E7FE4041 3266E416 710D13ED 22BD4D5 huawei(config-rsa-key-code)#DF0C3E46 A995CC61 DC4CB179 F6888B8C 3F8A3085 51EDB5C...
  • Page 84 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 1 Commissioning huawei(config-rsa-key-code)#5DEBDBE1 3AB4A256 0D0B9AA8 9A419D85 35C0E562 AE0BBFA huawei(config-rsa-key-code)#515299F9 D2803E84 3AE36C20 949367EA 0697EB20 2594A77 huawei(config-rsa-key-code)#9A0EFF04 26928874 FF9124C4 D28F0702 0125 huawei(config-rsa-key-code)#public-key-code end huawei(config-rsa-public-key)#peer-public-key end Step 9 Assign the public key to the SSH user.
  • Page 85 Figure 1-43. Input the user name to log in to the system (here, the user name is huawei). Figure 1-43 Interface for logging in to the system using the SSH client software ----End...

  • Page 86: Checking The Software State

    SCUN board to the OLT mode, ensuring that the memory is allocated properly and services are processed smoothly. ----End Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 87 If the version of the host software and the version of the board software do not meet the deployment requirement, contact the Huawei Customer Service Center. Upgrade the host software if necessary.

  • Page 88: Loading A Configuration Script

    Open the configuration script, and copy the commands in the configuration script to the command line interface (CLI). However, the following contents must be deleted. Otherwise, the script loading will fail. – Delete the following tags. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 89: Changing The System Name

    Example To name the first MA5600T/MA5603T/MA5608T at Longgang (a district in Shenzhen, Guangdong, China) guangdong_shenzhen_longgang_MA5600T/MA5603T/MA5608T_A based on the rule province_city_district_device name_SN, do as follows: huawei(config)#guangdong_shenzhen_longgang_MA5600T/MA5603T/MA5608T_A guangdong_shenzhen_longgang_MA5600T/MA5603T/MA5608T_A(config)# Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 90: Configuring The System Time

    Run the ntp-service unicast-server command to configure the NTP unicast server mode, and specify the IP address of the remote server that functions as the local time server and the interface for transmitting and receiving NTP packets. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 91 4 huawei(config)A#ntp-service unicast-server 10.20.20.20 source-interface vlanif 2 huawei(config)A#time dst start 5-1 00:00:00 end 9-30 00:00:00 adjust 1:00 Assume that the current time zone of MA5600T/MA5603T/MA5608T A is GMT- 4:00, the local time is used, the current time is 2010-01-01 12:10:10. The start time is 00:00:00 on May 1, the end time is 00:00:00 on September 30, and the adjust time is 2:00.

  • Page 92: Configuring A System User

    Commissioning and Configuration Guide 1 Commissioning huawei(config)A#time 2010-01-01 12:10:10 huawei(config)A#time dst start 5-1 00:00:00 end 9-30 00:00:00 adjust 2:00 1.3.10 Configuring a System User For logging in to, configuring, and managing the MA5600T/MA5603T/MA5608T, system users of different attributes need to be added. This topic describes how to add a system user and modify the user attributes.
  • Page 93 Step 2 Run the display terminal user command to query the user information. ----End Result The queried user information is the same as the actual data plan. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 94: Modifying The System User Attributes

    1 Commissioning Example With the administrator authority, to add a common user with the account as huawei, password as test01, user profile as the default root user profile, user level as Common User, permitted reenter number as 3, and appended information as user, do as follows: huawei(config)#terminal user name User Name(length<6,15>):huawei...
  • Page 95 Step 2 Check the user information. Run the display terminal user command to query the user information. ----End Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 96: Configuring A Board

    MA5600T/MA5603T/MA5608T by using the original user name and password is successful. Example To modify the attributes of user huawei, including changing the password to test02, user profile to operator profile, user level to operator, permitted reenter number to 4, and appended information to operator, do as follows: huawei(config)#terminal user password User Name(<=15 chars):huawei...

  • Page 97: Adding A Board Offline

    0/2 --------------------------------------- Board Name : H802GPBD Board Status : Failed --------------------------------------- ------------------------------------------------------------- Port Port min-distance max-distance Optical-module type (km) (km) status ------------------------------------------------------------- GPON GPON GPON GPON GPON Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 98: Confirming A Board

    Port Port Type Port Status Line Profile Alarm Profile Ext Profile ----------------------------------------------------------------------------- ADSL Activating 1002 ADSL Activating 1002 ADSL Activating 1002 ADSL Activating 1002 ADSL Activating 1002 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 99: Checking The Board Status

    0 ------------------------------------------------------------------------- SlotID BoardName Status SubType0 SubType1 Online/Offline ------------------------------------------------------------------------- H802GPBD Normal H802GPBD Normal H801SCUL Active_normal FLBA H802GPBD Normal H802GPBD Normal H802GPBD Normal H801GICG Normal ------------------------------------------------------------------------- Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 100: Checking The Status Of The Upstream Port

    Run the interface gpon command to enter the GPON mode. Run the display port state command to check whether the service port is in the normal state. ----End Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 101: Enabling The Ont Automatic Discovery Function

    1.3.15.1 Measuring the Transmit Optical Power of an OLT PON Port Check whether the optical module on a PON port of the OLT works properly by measuring the transmit optical power. Prerequisites The OLT is powered on. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 102 1-45. The value on the optical power meter is the transmit optical power of the OLT PON port. Figure 1-45 Measuring the Transmit Optical Power of an OLT PON Port Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 103: Measuring The Receive Optical Power Of An Olt Pon Port

    This is because if a contaminated optical fiber is connected to a normal optical fiber connector, the connector will be contaminated, which leads to abnormal attenuation and reflection and thus affecting optical path quality. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 104: Measuring The Transmit Optical Power Of An Onu Pon Port

    PON port functions properly and whether the ONU is a continuous-mode ONU or a rogue ONU. Prerequisites The ONU is powered on. The PON port is enabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 105 Figure 1-47 Measuring the transmit optical power of an ONU PON port Step 4 Wait 10s and then read the value. Check the value on the optical power meter in one minute. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 106: Measuring The Receive Optical Power Of An Onu Pon Port

    Measuring the receive optical power of an ONU PON port helps to check the optical path quality. Prerequisites The OLT is powered on. The OLT PON port is enabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 107 1-48. The value read on the optical power meter is the receive optical power of the ONU PON port. Figure 1-48 Measuring the Receive Optical Power of an ONU PON Port Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 108: Commissioning The Emu

    ESCM EPS75-4815AF Monitoring F01D500 One MA5600T(MA5603T) Solution (PMIB01) shelf EPS30-4815AF Monitoring F01S300 One MA5603T shelf Solution (PMIB01) GEPS4845 Monitoring F01D500 One MA5600T(MA5603T) Solution shelf Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 109: Commissioning The Emu_Esc

    Table 1-23 lists the default configuration of the H801ESC board. Table 1-23 Default configuration of the H801ESC board Parameter Default Value Sub-node Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 110 Step 2 Insert the H801ESC board into the corresponding slot of the PDU, and make sure that the MA5600T/MA5603T/MA5608T and the H801ESC board are connected through the RS-485 serial port cable. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 111 1 H801ESC 0 15 H801ESC huawei(config)#interface emu 1 huawei(config-if-h801esc-1)#esc analog 5 alarm-upper-limit 70 alarm-lower-limit -30 name Temperature_1 unit C huawei(config-if-h801esc-1)#esc digital 7 digital-alarm 8 name Door_1 available- level high-level huawei(config-if-h801esc-1)#display esc system parameter huawei(config-if-h801esc-1)#quit huawei(config)#save...

  • Page 112: Configuring H801Vesc Environment Monitoring Parameters

    To configure the H801VESC of the MA5608T in an F01S200 cabinet, do as follows (Table 1-24 lists the data plan for configuring the H801VESC of the MA5608T in the F01S200 cabinet): Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 113 The fan monitoring digital parameter is required only when the enhanced heat dissipation module is configured. Otherwise, the system will report an alarm. huawei(config)#emu add 2 H801VESC 0 25 H801VESC huawei(config)#display emu 2 Issue 01 (2014-04-30) Huawei Proprietary and Confidential...

  • Page 114: Configuring The Environment Monitoring Parameters Of The Eps30-4815Af

    : 25 ---------------------------------------------------------------------------- huawei(config)#interface emu 2 huawei(config-if-h801vesc-2)#vesc digital 0 available-level low-level name Temperature huawei(config-if-h801vesc-2)#vesc digital 1 available-level low-level name Door huawei(config-if-h801vesc-2)#vesc digital 2 available-level low-level name Arrester huawei(config-if-h801vesc-2)#vesc digital 3 available-level low-level name Fan huawei(config-if-h801vesc-2)#display vesc environment info EMU ID: 2...
  • Page 115 Configure the battery set power- power off off parameters Configure the power distribution power supply-parameter parameters Configure the battery power battery-test discharging test parameters Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 116 In this topic, the application in the F01S300 cabinet is considered as an example. Table 1-27 provides the data plan for configuring the monitoring parameters of the EPS30-4815AF. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 117 EPS30-4815AF supports up to 2 rectifier modules. Battery high- Battery high-temperature power-off permission status: permit temperature power- Temperature for battery high-temperature power-off: 53°C off parameters Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 118 Valid level of digital parameter 3: low level When the low level represents the valid level, the host does not report an alarm in the case of low level. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 119 Configuration Example The following considers the configuration in the F01S300 cabinet as an example to describe the process of configuring the environment monitoring parameters of the EPS30-4815AF. huawei(config)#emu add 0 POWER4830L 0 0 POWER4830L huawei(config)#display emu 0 huawei(config)#interface emu 0...

  • Page 120: Configuring The Environment Monitoring Parameters Of The Eps75-4815Af

    Digital 3 JTD4 Not connected by default, surge protector used to add a user-defined monitoring digital parameter Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 121 The monitoring parameters can be reported to the control system only when the data for the EPS75-4815AF is configured correctly in the system. Table 1-29 lists the commands used during the configuration. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 122 Query the status of the EPS75-4815AF. Enter the environment monitoring configuration mode and query the default configuration. Configure the battery management parameters. Configure the battery discharging test parameters. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 123 Equalized charging voltage of the battery: 56.5 V battery: 56.5 V Float charging voltage of the Float charging voltage of the battery: battery: 53.5 V 53.5 V Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 124 EPS75-4815AF actual value. EPS75-4815AF supports supports up to 5 rectifier modules. up to 5 rectifier modules. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 125 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 126 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 127 Configuration Example The following considers the configuration in the F01D500 cabinet as an example to describe the process of configuring the environment monitoring parameters of the EPS75-4815AF. huawei(config)#emu add 0 POWER4875L 0 0 POWER4875L huawei(config)#display emu 0 huawei(config)#interface emu 0...

  • Page 128: Configuring The Environment Monitoring Parameters Of The Geps4845

    Access Module Commissioning and Configuration Guide 1 Commissioning huawei(config-if-power4875l-0)#power temperature-off battery-off-state permit battery-off-temperature 53 huawei(config-if-power4875l-0)#power environment temperature 68 -5 80 -20 huawei(config-if-power4875l-0)#power outside-digital 3 available-level low-level name SPD digital-alarm 20 huawei(config-if-power4875l-0)#power outside-digital 4 available-level high-level name Smoke digital-alarm 15 huawei(config-if-power4875l-0)#power outside-digital 5 available-level low-level...
  • Page 129 Configure the upper/lower power battery temperature temperature alarm limits or the upper/lower temperature test limits Configure the power supply load power off power-off and battery set power- off parameters Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 130 In this topic, the application in the F01D500 cabinet is considered as an example. Table 1-33 provides the data plan for configuring the monitoring parameters of the GEPS4845. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 131 The number of the power rectifier modules: 0 parameters The number of the power rectifier modules is configured according to the actual value. GEPS4845 supports up to 3 rectifier modules. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 132 Valid level of digital parameter 3: low level When the low level represents the valid level, the host does not report an alarm in the case of low level. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 133 Configuration Example The following considers the configuration in the F01D500 cabinet as an example to describe the process of configuring the environment monitoring parameters of the GEPS4845. huawei(config)#emu add 0 POWER4845 0 0 POWER4845 huawei(config)#display emu 0 huawei(config)#interface emu 0...

  • Page 134: Configuring The Environment Monitoring Parameters Of The Etp4830

    Door status sensor of the MDF compartment Door alarm JTM1 Door status sensors of the device compartment and heat exchanger compartment Wiring alarm JTP1 Battery Tem VBTEM2 Battery temperature sensor Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 135 Run the power environment command to configure the upper alarm threshold and the upper and lower test thresholds for the temperatures and humidity. After these parameters are set, the Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 136 Charging Charging mode of the battery: automatic parameters of the Equalized charging voltage of the battery (V): 56.5 battery Float charging voltage of the battery (V): 53.5 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 137 Lower test threshold of the humidity (% RH): 0 Power rectifier The number of the power rectifier modules is configured according to module parameters the actual value. ETP4830 supports up to 2 rectifier modules. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 138 When the heat exchanger is faulty, the device reports an alarm. The heat exchanger has the low level when working properly and the device does not report an alarm. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 139 2 rectifier modules, and battery compartment heater and equipment compartment heater are configured. To configure the environment monitoring parameters of the ETP4830, do as follows: huawei(config)#emu add 1 SMU 0 0 SMU huawei(config)#display emu 1 huawei(config)#interface emu 1...

  • Page 140: Configuring The Environment Monitoring Parameters Of The Etp4890

    JTM1 Door status sensors of the device compartment and heat exchanger compartment Wiring alarm JTP1 Battery Tem VBTEM2 Battery temperature sensor environment Tem VTEM2 Environment temperature sensor Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 141 After these parameters are set, the system reports alarms if the working environment of the power system does not meet requirements. Step 9 Configure required parameters for the rectifier module. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 142 Charging parameters of Charging mode of the battery: automatic the battery Equalized charging voltage of the battery (V): 56.5 Float charging voltage of the battery (V): 53.5 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 143 Lower test threshold of the humidity (% RH): 0 Power rectifier module The number of the power rectifier modules is configured parameters according to the actual value. ETP4890 supports up to 3 rectifier modules. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 144 Assume that the F01D500 cabinet is configured with two 75 AH battery sets, the ETP4890 is configured with 3 rectifier modules. To configure the environment monitoring parameters of the ETP4890, do as follows: huawei(config)#emu add 1 SMU 0 0 ETP4890 huawei(config)#display emu 1 huawei(config)#interface emu 1...

  • Page 145: Configuring The Power3000 Environment Monitoring Mode

    43 huawei(config-if-smu-1)#power temperature-off battery-off-state permit battery-off- temperature 53 huawei(config-if-smu-1)#power environment temperature 68 -5 80 -20 This command is invalid unless in the contition of install the sensor, would you continue? (y/n)[n]:y huawei(config-if-smu-1)#power environment humidity 80 0 100 0...
  • Page 146 Query the information about the configured parameters and environment parameters of the power system. 10. Save the data. Data Plan Table 1-39 provides the data plan for configuring the monitoring parameters of the Power3000. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 147 POWER3000 supports up to 12 rectifier modules. Battery high-temperature Battery high-temperature power-off permission status: permit power-off parameters Temperature for battery high-temperature power-off: 53°C Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 148: Commissioning The Emu_Tcu

    Configuration Example The following considers the configuration plan of the Power3000 as an example to describe the process of configuring the environment monitoring parameters of the Power3000. huawei(config)#emu add 0 POWER3000 0 0 POWER3000 huawei(config)#display emu 0 huawei(config)#interface emu 0...
  • Page 149 In the TCU mode, run the display tcu alarm command to query the alarm information reported by the TCU. The status of all the heat exchanger alarms is normal. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 150: Commissioning The Emu_Fan

    To add a TCU (emuid: 2; sub-node: 7), and set the heating start temperature to -10°C and the heating stop temperature to 30°C for heat exchanger 2, do as follows: huawei(config)#emu add 2 TCU 0 7 tcu huawei(config)#interface emu 2 huawei(config-if-tcu-2)#tcu heat temperature { start-temperature<F><-90,40>...
  • Page 151 The status of all the fan alarms is normal. Example To add a FAN, and adopt the default settings for the speed adjustment mode and alarm function, do as follows: huawei(config)#emu add 0 FAN 0 1 FAN huawei(config)#interface emu 0 huawei(config-if-fan-0)#display fan system parameter EMU ID: 0...

  • Page 152: Saving And Backing Up Data

    Manually save the database save Saves the database file and file and the configuration the configuration file. file Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 153 ----End Result The system displays a message indicating that the database file and the configuration file have been saved successfully. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 154 Note: The configuration file will take effect after being activated To save the database file and the configuration file in the system, do as follows: WS6803(config)#save { <cr>|configuration<K>|data<K> }: Command: save huawei(config)# Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 155 Are you sure to continue? (y/n)[n]: y Load(backup,duplicate,...) begins, please wait and notice the rate of progress Any operation such as reboot or switchover will cause failure and unpredictable result Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 156: Configuring The Auto-Save And Auto-Backup Functions

    If data is modified, the system automatically saves the modified data. Otherwise, the system does not perform the auto-save operation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 157 An auto-backup server backs up data, configuration, and logs of a device to an external server. After an auto-backup server is configured, you can configure the auto-backup function. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 158 Set the interval and start time of automatically backing up configuration files and then enable the auto-backup function for configuration files. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 159 The system checks whether the configuration data is modified every 1440 minutes. If the configuration data is modified, the system automatically saves the modified configuration. Otherwise, the system does not perform the auto-save operation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 160: Interconnection Commissioning

    Different offices have different conditions; therefore, it is recommended that customers, with the assistance of Huawei engineers, modify commissioning tasks according to actual requirements. Issue 01 (2014-04-30) Huawei Proprietary and Confidential...

  • Page 161: Commissioning The Interconnection With The Nms

    Figure 1-49 Example network for the outband network management Router U2000 Access node 10.50.1.10/24 10.50.1.1/24 10.10.1.10/24 Figure 1-50 shows the flowchart for commissioning the outband network management on the device. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 162 10.10.1.0 24 10.50.1.1 Set the SNMP parameters. Configure the community name and the access authority. The read community name is public, and the write community name is private. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 163 Configure the IP address of the destination host for the traps. – When the SNMP V1 is used, the host name is huawei, the IP address of the host is 10.10.1.10/24 (IP address of the U2000), the trap parameter name is ABC, SNMP version is V1, and the parameter security name is private (the parameter security name is the SNMP community name).
  • Page 164 Access Protocol Parameters tab page. Then click Add and set the SNMP parameters, as shown in the following figure (the other parameters except Profile name use the default settings). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 165 – When the SNMP V1 is used, In the dialog box that is displayed, set the required parameters, as shown in the following figure. IP Address is 10.50.1.10, Device Name is huawei, and SNMP Parameters is SNMP V1:default. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright ©...
  • Page 166 – When the SNMP V2 is used, In the dialog box that is displayed, set the required parameters, as shown in the following figure. IP Address is 10.50.1.10, Device Name is huawei, and SNMP Parameters is SNMP V2:default. Figure 1-54 Add device...
  • Page 167 HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v1 snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v1 securityname private snmp-agent trap source meth 0 save The following describes the script for commissioning the outband network management on the device (SNMP V2).

  • Page 168: Commissioning Outband Management (Snmp V3)

    Figure 1-55 Example network for the outband network management Router U2000 Access node 10.50.1.10/24 10.50.1.1/24 10.10.1.10/24 Figure 1-56 shows the flowchart for commissioning the outband network management on the device. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 169 Configure the SNMP user, group, and view. The user name is user1, the group name is group1, the user authentication mode is SHA, the authentication password is authkey123, the user encryption mode Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 170 Configure the IP address of the destination host for the traps. The host name is huawei, the IP address of the host is 10.10.1.10/24 (IP address of the U2000), the trap parameter name is ABC, the SNMP version is V3, the parameter security name is user1 (when the SNMP V3 is used, the parameter security name is the USM user name), and the traps are authenticated and encrypted.
  • Page 171 After selecting corresponding protocols in Priv Protocol and Auth Protocol, click next to the parameter, and set the passwords of data encryption protocol and authentication protocol, as shown in Figure 1-58. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 172 In the dialog box that is displayed, set the required parameters, as shown in Figure 1-59. IP address is 10.50.1.10, Device Name is huawei, SNMP Parameters is SNMP V3:default. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 173 HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v3 snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v3 securityname user1 privacy Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 174: Commissioning Inband Management (Snmp V1 And V2)

    Figure 1-60 Example network for the inband network management Router U2000 Access node 10.50.1.1/24 10.10.1.10/24 VLAN:1000 10.50.1.10/24 Figure 1-61 shows the flowchart for commissioning the inband network management. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 175 U2000 belongs), and the gateway IP address is 10.50.1.1/24 (the IP address of the gateway of the MA5600T/MA5603T/MA5608T). huawei(config)#ip route-static 10.10.1.0 24 10.50.1.1 Set the SNMP parameters. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 176 Configure the IP address of the destination host for the traps. – When the SNMP V1 is used, the host name is huawei, the IP address of the host is 10.10.1.10/24 (IP address of the U2000), the trap parameter name is ABC, SNMP version is V1, and the parameter security name is private (the parameter security name is the SNMP community name).
  • Page 177 Access Protocol Parameters tab page. Then click Add and set the SNMP parameters, as shown in the following figure (the other parameters except Profile name use the default settings). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 178 – When the SNMP V1 is used, In the dialog box that is displayed, set the required parameters, as shown in the following figure. IP Address is 10.50.1.10, Device Name is huawei, and SNMP Parameters is SNMP V1:default. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright ©...
  • Page 179 – When the SNMP V2 is used, In the dialog box that is displayed, set the required parameters, as shown in the following figure. IP Address is 10.50.1.10, Device Name is huawei, and SNMP Parameters is SNMP V2:default. Figure 1-65 Add device...
  • Page 180 HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v1 snmp-agent trap enable standard snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v1 securityname private snmp-agent trap source vlanif 1000 save The following describes the script for commissioning the inband network management on the device (SNMP V2).

  • Page 181: Commissioning Inband Network Management (Snmp V3)

    Figure 1-66 Example network for the inband network management Router U2000 Access node VLAN:1000 10.50.1.1/24 10.10.1.10/24 10.50.1.10/24 Figure 1-67 shows the flowchart for commissioning the inband network management. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 182 U2000 belongs), and the gateway IP address is 10.50.1.1/24 (the IP address of the gateway of the MA5600T/MA5603T/MA5608T). huawei(config)#ip route-static 10.10.1.0 24 10.50.1.1 Log in to the U2000. Set the SNMP parameters. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 183 Configure the IP address of the destination host for the traps. The host name is huawei, the IP address of the host is 10.10.1.10/24 (IP address of the U2000), the trap parameter name is ABC, the SNMP version is V3, the parameter security name is user1 (when the SNMP V3 is used, the parameter security name is the USM user name), and the traps are authenticated and encrypted.
  • Page 184 After selecting corresponding protocols in Priv Protocol and Auth Protocol, click next to the parameter, and set the passwords of data encryption protocol and authentication protocol, as shown in Figure 1-69. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 185 In the dialog box that is displayed, set the required parameters, as shown in Figure 1-70. IP address is 10.50.1.10, Device Name is huawei, SNMP Parameters is SNMP V3:default. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 186 HW-075528780808 snmp-agent sys-info location Shenzhen_China snmp-agent sys-info version v3 snmp-agent trap enable standard Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 187: Commissioning The Interconnection With The Router

    SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 1 Commissioning snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC snmp-agent target-host trap-paramsname ABC v3 securityname user1 privacy snmp-agent trap source vlanif 1000 save 1.4.2 Commissioning the Interconnection with the Router...

  • Page 188: Commissioning The Interconnection With The Bras

    BRAS. If the BRAS is used to allocate IP addresses, you must configure the corresponding IP address pool on the BRAS. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 189 After the MA5600T/MA5603T/MA5608T is interconnected with the BRAS successfully, you can ping IP address 10.10.1.1 from the MA5600T/MA5603T/MA5608T. After services are configured on the MA5600T/MA5603T/MA5608T, the authentication and accounting functions of the BRAS can be implemented. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 190: Interconnection Commissioning Of The Mg Interface

    VLAN tag. Figure 1-73 Example network for commissioning the interconnection with the MG interface (H.248) Access node H.248 Router VLAN:50 Phone 10.10.1.4/24 10.50.1.1/24 10.50.1.10/24 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 191 The VLAN ID is 50, the VLAN type is smart VLAN, the upstream port is 0/19/0, and the IP address of the VLAN interface is 10.50.1.10/24. huawei(config)#vlan 50 smart huawei(config)#port vlan 50 0/19 0 huawei(config)#interface vlanif 50 huawei(config-if-vlanif50)#ip address 10.50.1.10 24 huawei(config-if-vlanif50)#quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 192 MA5600T/MA5603T/MA5608T.com, the IP address of the primary MGC is 10.10.1.4/24, the MGC port ID is 2944, and the start negotiation version of the H.248 is V2. huawei(config-if-h248-0)#if-h248 attribute mgip 10.50.1.10 mgport 2944 code text transfer udp domainName MA5600T/MA5603T/MA5608T.com primary-mgc-ip1 10.14.1.4 primary-mgc-port 2944 mg- media-ip1 10.50.1.10 start-negotiate-version 2...

  • Page 193: Commissioning The Interconnection With The Mg Interface (Mgcp)

    MG interface use the default settings. The MGC identifies the MG through the signaling IP address (IP address of the MG interface), and their communication packets do not contain any VLAN tag. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 194 Figure 1-76 Flowchart for commissioning the interconnection with the MG interface (MGCP) Prerequisites The data configuration on the MGC side (corresponding to the data configuration on the MG side) must be correct. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 195 (default setting), the transmission mode is UDP (default setting), the MG domain name is MA5600T/MA5603T/MA5608T.com, the IP address of the primary MGC is 10.10.1.4/24, and the MGC port ID is 2727. huawei(config-if-mgcp-0)#if-mgcp attribute mgip 10.50.1.10 mgport 2727 domainName MA5600T/MA5603T/MA5608T.com mgcip_1 10.10.1.4 mgcport_1 2727 Step 6 Reset the MG interface.

  • Page 196: Commissioning The Interconnection With The Sip Interface

    The IMS identifies the SIP interface through the signaling IP address (IP address of the SIP interface), and their communication packets do not contain any VLAN tag. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 197 Run the display protocol support command to query the current voice protocol. If the voice protocol is not SIP, run the protocol support sip command to change it to SIP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 198 10.10.1.2 secondary-proxy-port 5555 home-domain MA5600T/ MA5603T/MA5608T.com sipprofile-index 0 Step 6 Configure the optional attributes of the SIP interface. The domain name of the SIP interface is huawei.com, and the phone context is +86755. huawei(config-if-sip-0)#if-sip attribute optional mg-domain huawei.com phone- context +86755 Step 7 Reset the SIP interface.

  • Page 199: Commissioning The Management Channel Between The Olt And The Gpon Mdu

    10.50.1.10 signal-ip 10.50.1.10 signal-port 5555 transfer udp primary-proxy-ip1 10.10.1.1 primary-proxy- port 5555 secondary-proxy-ip1 10.10.1.2 secondary-proxy-port 5555 home-domain MA5600T/ MA5603T/MA5608T.com sipprofile-index 0 if-sip attribute optional mg-domain huawei.com phone-context +86755 reset quit save 1.4.6 Commissioning the Management Channel Between the OLT...
  • Page 200 GPON MDU BRAS Access node VLAN: 20 192.168.1.100/24 Optical splitter 192.168.1.200/24 Figure 1-80 shows the flowchart for commissioning the management channel between the OLT and the GPON MDU. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 201 Figure 1-80 Flowchart for commissioning the management channel between the OLT and the GPON MDU Procedure Step 1 Create a VLAN. The VLAN ID is 20, and the VLAN type is smart VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 202 You can also run the port ont-auto-find command to enable the function of auto-discovering an MDU, and then run the ont confirm command to confirm the auto-discovered MDU. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 0 0 sn-auth 32303131B39FD641 snmp ont- lineprofile-id 5 Step 7 Configure the management IP address of the MDU.
  • Page 203 0 0 ip-address 10.10.1.10 mask 255.255.255.0 next-hop 192.168.1.101 huawei(config-if-gpon-0/2)#quit Step 9 Add a service port to the VLAN. huawei(config)#service-port vlan 20 gpon 0/2/0 ont 0 gemport 0 multi-service user- vlan 20 Step 10 Save the data. huawei(config)#save ----End...

  • Page 204: Commissioning The Management Channel Between The Olt And The Gpon Ont

    The DBA profile is used to limit the user rate to the fixed 10 Mbit/s bandwidth. Figure 1-81 Example network for commissioning the management channel between the OLT and the GPON ONT BRAS Access node VLAN: 20 192.168.1.100/24 Splitter 192.168.1.200/24 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 205 The DBA profile ID is 12, the DBA profile uses the default name DBA-profile_12, the bandwidth type is type1 (fixed bandwidth), and the user rate is the fixed 10 Mbit/s bandwidth. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 206 You can also run the port ont-auto-find command to enable the function of auto-discovering an ONT, and then run the ont confirm command to confirm the auto-discovered ONT. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 0 0 sn-auth 323031314D4B2041 omci ont- lineprofile-id 5 ont-srvprofile-id 10 huawei(config-if-gpon-0/2)#quit Step 5 Save the data.

  • Page 207: Commissioning The Management Channel To The Xdsl Cpe

    After the management channel between the DSLAM and the CPE is set up, you can log in to the CPE using port 0/2/0 connected to the CPE to remotely maintain and manage the CPE. The user access mode is IPoA. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 208 Figure 1-84 Flowchart for commissioning the management channel to the CPE Prerequisites You must be logged in to the MA5600T/MA5603T/MA5608T using the maintenance terminal. Procedure Step 1 Configure the management IP address of the CPE. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 209 30 ip address 192.168.10.11 24 quit cpe-management vpi 0 vci 35 cpe-management flow-type vlan-ethertype ipoe mac-pool 0 0000-0000-0001 ipoa enable ipoa default gateway 10.1.1.1 cpe-management telnet 0/2/0 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 210: Maintenance And Management Commissioning

    To power on a board that is powered off manually, you must run the board power-on command to manually power it on. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 211 To reference energy-saving profile 4 to enable the system energy-saving function, do as follows: Assume that battery energy saving is enabled and energy saving for unused boards is enabled. huawei(config)#spm-profile profile-id 4 huawei(config-spm-prof-4)#unused-slot shutdown enable huawei(config-spm-prof-4)#battery energy-saving ac-monitor emuid 1 digitalid 6 huawei(config-spm-prof-4)#battery energy-saving enable huawei(config-spm-prof-4)#quit huawei(config)#system energy-saving mode profile-id 4...

  • Page 212: Checking Alarms And Events

    1.5.2.2 Querying Alarms and Events This topic describes how to query history alarms and events through the maintenance terminal. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 213 Query events by event display event history eventsn sn [ detail | list ] Query events by event display event history eventid id [ detail | list | start-number number] Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 214 The system resources usage exceeds the threshold Resource Name: CPU, Current Percent: 86 2009-08-21 10:17:29 The system resources usage recovers from the overload state to the normal state Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 215: Checking The Log

    Step 2 In the user mode, run the display log command to query the records in the log. ----End Result You can query the log record generated by the operation you have performed. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 216: Checking The System Switchover

    When the communication between the active and standby control boards fails or the standby control board is faulty, the system prohibits the active/standby switchover. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 217 When the ACT LED on the original standby control board is on, log in to the system through this control board. It is found that the system runs in the normal state. Example After the data is saved, perform the active/standby switchover. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 218: Supplementary Information

    MA5600T/MA5603T/MA5608T through the maintenance terminal in the management center to commission the basic functions of the device. Table 1-49 Script data plan Item Data PRTE power board Slot IDs: 0/21 and 0/22 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 219: Configuring The File Transfer Mode

    1.6.2 Configuring the File Transfer Mode This topic describes how to configure the file transfer mode of the FTP,SFTP, Xmodem and TFTP. SFTP with high security is recommended. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 220: Configuring The Ftp Transfer Mode

    MA5600T/MA5603T/MA5608T, run the ftp set command to set the FTP user name and password. huawei(config)#ftp set User Name(<=40 chars):huawei User Password(<=40 chars):huawei//The input is not displayed on the CLI. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 221: Configuring The Sftp Transfer Mode

    Commissioning and Configuration Guide 1 Commissioning NOTE By default, the FTP user name is anonymous and the password is anonymous@huawei.com in the MA5600T/MA5603T/MA5608T system. Step 4 (Optional; this step is required when the function of database file auto-backup is used.) On the MA5600T/MA5603T/MA5608T, run the file-server auto-backup data command to configure the FTP user name, password, and port ID.

  • Page 222: Configuring Xmodem File Transfer Mode

    MA5600T/MA5603T/MA5608T, run the ssh sftp set command to set the SFTP user name, password, and port ID. huawei(config)#ssh sftp set User Name(<=40 chars):huawei User Password(<=40 chars):huawei//The input is not displayed on the CLI. Listening Port(0--65535):22 NOTE The MA5600T/MA5603T/MA5608T system does not have default SFTP user name, password, or port ID.
  • Page 223 Step 3 Open the HyperTerminal on the console to configure the baud rate of the serial port on the console to be the same as the baud rate on the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 224: Configuring The Tftp Transfer Mode

    You have logged in to the MA5600T/MA5603T/MA5608T remotely from the console (maintenance terminal), and have entered the global config mode. Tools, Meters, and Materials Crossover cable Direct cable Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 225 In the interface as shown in Figure 1-85, click Settings. In the dialog box that is displayed, click Browse to select the path for saving the file, as shown in Figure 1-86. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 226 – Whether the path is correctly set in the TFTP application. – Whether the TFTP file transfer function has been enabled through the command. – Whether the entered name of the file to be transferred is correct. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 227: Software Package Settings

    Target SNR margin downstream (0.1dB) Minimum SNR margin downstream (0.1dB) Maximum SNR margin downstream(0.1dB) Target SNR margin upstream (0.1dB) Minimum SNR margin upstream (0.1dB) Maximum SNR margin upstream (0.1dB) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 228 PSD upstream (-0.1dBm) Maximum nominal aggregate transmit power downstream(0.1dBm) Maximum nominal aggregate transmit power upstream(0.1dBm) Upstream PSD mask ADLU-32/EU-32 selection Network timing reference clock FreeRun mode Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 229 UPBO US3 band reference PSD parameters [a, b] UPBO US4 band reference PSD parameters [a, b] UPBO Boost Mode Enable UPBO US1 band reference electrical length 0 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 230 Virtual noise mode upstream Disable Network timing reference clock mode FreeRun INM inter arrival time offset downstream (symbol) INM inter arrival time step downstream INM cluster continuation value downstream (symbol) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 231 Minimum impulse noise protection of ROC upstream Table 1-52 SHDSL line profile Profile Profile Parameter Factory Default Index DEFVA Path mode G.SHDSL interface mode of line two wire Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 232: Factory Defaults Of The Xdsl Alarm Profile

    The number of severely errored seconds The number of loss of signal seconds The number of unavailable seconds The number of forward error correction seconds The number of errored seconds Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 233 The number of severely errored seconds The number of loss of signal seconds The number of unavailable seconds The number of failed full initialization The number of full initialization Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 234: Default Settings Of The System Parameters

    2:FSK no ring Global digitmap support flag 0:Not support, 1:Support Transfer mode of media stream in a device, 0:Device internal forwarding, 1:Device external forwarding RTP 2833 Payload Type Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 235: Default Settings Of The Overseas Parameters

    Profile-name dba-profile_1 Profile-ID Type Bandwidth compensation Fix bandwidth(kbps) 5120 Assure bandwidth(kbps) Maximum bandwidth(kbps) Table 1-59 DBA profile 2 Profile Name Default Profile-name dba-profile_2 Profile-ID Type Bandwidth compensation Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 236 Profile Name Default Profile-name dba-profile_4 Profile-ID Type Bandwidth compensation Fix bandwidth(kbps) 1024000 Assure bandwidth(kbps) Maximum bandwidth(kbps) Table 1-62 DBA profile 5 Profile Name Default Profile-name dba-profile_5 Profile-ID Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 237 Fix bandwidth(kbps) 102400 Assure bandwidth(kbps) Maximum bandwidth(kbps) Table 1-64 DBA profile 7 Profile Name Default Profile-name dba-profile_7 Profile-ID Type Bandwidth compensation Fix bandwidth(kbps) Assure bandwidth(kbps) 32768 Maximum bandwidth(kbps) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 238: Default Settings Of The Gpon Ont Line Profile

    The following table lists the default settings of the GPON ONT line profile on the MA5600T/ MA5603T/MA5608T. Table 1-67 GPON ONT line profile Parameter Name Default FEC upstream switch Disable Qos mode Mapping mode VLAN <T-CONT 0> DBA Profile-ID:1 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 239: Default Settings Of The Gpon Ont Service Profile

    The following table lists the factory defaults of a GPON ONT alarm profile on the MA5600T/ MA5603T/MA5608T. Table 1-69 GPON ONT alarm profile Profile Profile Parameter Factory Default Index alarm- GEM port loss of packets threshold profile_ GEM port misinserted packets threshold Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 240 MAC bridge port MTU exceeded discard frames threshold MAC bridge port received incorrect frames threshold CES general error time threshold CES severely time threshold CES bursty time threshold Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 241: Default Settings Of The Environment Monitoring Units

    5-8: user-defined analog parameters allocated to other extended analog sensors, such as the humidity sensor. Upper and lower alarm thresholds l Temperature: 5°C to 55°C l Humidity: 0% RH to 80% RH Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 242 Table 1-71 Default settings of the FAN Parameter Default Sub-node Fan speed Automatic adjustment mode Whether to report Permit the fan alarm Table 1-72 Default settings of the TCU Parameter Default Sub-node Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 243: Basic Configurations

    DOCSIS 3.0 defines various DOCSIS events, such as authentication failure and CM certificate error events. Configuring DOCSIS event reporting helps you obtain MA5600T/MA5603T/ MA5608T and CM running status. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 244: Configuring Alarms

    NMS immediately but is reported to the NMS after an alarm jitter-proof period. – If an alarm is recovered in an alarm jitter-proof period, the alarm is not reported to the NMS. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 245 (Optional) Configure alarm policy for ONT. In FTTH scenarios, you can configure the ONT alarm policy profile to configure alarms for different service policies. Create an ONT alarm policy profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 246 0x2e313016 (The ONT switches to the standby battery) 0x2e313017 (The standby battery of the ONT is lost) 0x2e313018 (The standby battery of the ONT cannot be charged) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 247: Adding Port Description

    0x2e313024 huawei(config-ont-alarm-policy-10)#alarm filter 0x2e313025 huawei(config-ont-alarm-policy-10)#alarm filter 0x2e31302a huawei(config-ont-alarm-policy-10)#commit huawei(config-ont-alarm-policy-10)#quit huawei(config)#interface gpon 0/3 huawei(config-if-gpon-0/3)#ont alarm-policy 0 1 policy-id 10 2.2 Adding Port Description This topic describes how to add port description. Prerequisites A board must be added to the system. Context After the description of a physical port on the board is added, the description facilitates information query in system maintenance.

  • Page 248: Configuring The Attributes Of An Upstream Ethernet Port

    100 read only supported (Optical GICK: Mbit/s Port) enabled l GE l Other GIU optical board: port: 1000 disabled Mbit/s l 10GE optical port: 10000 Mbit/s Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 249 Ethernet port can be full-duplex, half-duplex, or auto negotiation. Pay attention to the following points: – Make sure that the ports of two interconnected devices work in the same duplex modes. This prevents communication failure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 250 Do as follows: huawei(config)#interface 0/19 huawei(config-if-0/19)#auto-neg 0 disable huawei(config-if-0/19)#speed 0 1000 huawei(config-if-0/19)#duplex 0 full huawei(config-if-0/19)#flow-control 0 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 251: Configuring Aaa

    MA5603T/MA5608T in the following three ways: The MA5600T/MA5603T/MA5608T functions as a local AAA server. In this case, the local AAA needs to be configured. The local AAA does not support accounting. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 252: Configuring The Local Aaa

    Run the aaa command to enter the AAA mode. Run the authentication-scheme command to add an authentication scheme. Run the authentication-mode local command to configure the authentication mode of the authentication scheme. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 253: Configuring The Remote Aaa (Radius Protocol)

    NOTE l A domain is a group of users of the same type. l In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name. l The domain name for user login cannot exceed 15 characters, and the other domain names cannot exceed 20 characters.
  • Page 254 Parameter Code Parameter Name Description User-Name Indicates the user name for authentication. Password Indicates the user password for authentication. This parameter is valid only for PAP authentication. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 255 Indicates the host IP address of a login user. Login-Service Indicates the login service type. The valid types are SSH, Rlogin, TCP Clear, PortMaster (proprietary), and LAT. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 256 1: charging start packet l 2: charging stop packet l 3: real-time charging packet Acct-Delay-Time Indicates the time for generating a charging packet in the unit of second. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 257 User-Request(1): The user actively goes offline. l Lost Carrier(2): The handshake fails, such as the EAPOL detection fails. l User Error(17): The user authentication fails or times out. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 258 After being delivered by the RADIUS server, this parameter is filled to suboption 7 in user DHCP packets by the MA5600T/MA5603T/ MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 259 The accounting scheme specifies how all the users in an ISP domain are charged. l The system supports up to 128 accounting schemes. The system has a default accounting scheme named default. It can be modified, but cannot be deleted. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 260 They can receive the packets from each other and can respond to each other only when their keys are the same. l By default, the shared key of the RADIUS server is huawei. (Optional) Run the radius-server timeout command to set the response timeout time of the RADIUS server.
  • Page 261 Step 4 Create a domain. A domain is a group of users of the same type. In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name.

  • Page 262: Configuration Example Of The Radius Authentication And Accounting

    The authentication port number is 1812, and the accounting port number is 1813. Other parameters adopt the default settings. Networking Figure 2-2 shows an example network of the RADIUS Authentication and Accounting application. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 263 RADIUS server 10.10.66.67 as the secondary authentication and accounting server. huawei(config)#radius-server template hwtacacs Note: Create a new server template huawei(config-radius-hwtacacs)#radius-server authentication 10.10.66.66 1812 huawei(config-radius-hwtacacs)#radius-server authentication 10.10.66.67 1812 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 264 10 quit quit radius-server template radtest radius-server authentication 10.10.66.66 1812 radius-server authentication 10.10.66.67 1812 secondary radius-server accounting 10.10.66.66 1813 radius-server accounting 10.10.66.67 1813 secondary quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 265: Configuring The Remote Aaa (Hwtacacs Protocol)

    Procedure Step 1 Configure the AAA authentication scheme. The authentication scheme specifies how all the users in an ISP domain are authenticated. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 266 HWTACACS server template mode. Run the hwtacacs-server authentication command to configure a primary authentication server. You can select secondary to configure a secondary authentication server. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 267 Run the quit command to return to the global config mode. Step 5 Create a domain. A domain is a group of users of the same type. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 268 Access Module Commissioning and Configuration Guide 2 Basic Configurations In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name. The domain name for user login cannot exceed 15 characters, and the other domain names cannot exceed 20 characters.

  • Page 269: Configuration Example Of The Hwtacacs Authentication (802.1X Access User)

    The HWTACACS server with the IP address 10.10.66.67 functions as the secondary server for authentication, authorization, and accounting. Other parameters adopt the default settings. Networking Figure 2-3 shows an example network of the HWTACACS authentication. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 270 Configure accounting scheme named newscheme (users are authenticated through HWTACACS). the interval is 10 minutes. huawei(config-aaa)#accounting-scheme newscheme huawei(config-aaa-accounting-newscheme)#accounting-mode hwtacacs huawei(config-aaa-accounting-newscheme)#accounting interim interval 10 huawei(config-aaa-accounting-newscheme)#quit huawei(config-aaa)#quit Step 4 Configure the HWTACACS protocol. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 271 EAP termination mode. The count of allowed handshake failure is 1 and the handshake interval is 20s. huawei(config)#dot1x keepalive retransmit 1 interval 20 service-port 1 huawei(config)#dot1x keepalive retransmit 1 interval 20 service-port 2...

  • Page 272: Configuration Example Of Hwtacacs Authentication (Management User)

    2.4.6 Configuration Example of HWTACACS Authentication (Management User) The MA5600T/MA5603T/MA5608T allows the management user of the device to log in to the system by the HWTACACS authentication mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 273 HWTACACS authentication. Figure 2-4 Example network of HWTACACS authentication Procedure Step 1 Configure the authentication scheme. Configure authentication scheme named login-auth (users are authenticated through HWTACACS). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 274 NOTE l A domain is a group of users of the same type. l In the user name format userid@domain-name (for example, huawei20041028@huawei.net), "userid" indicates the user name for authentication and "domain-name" followed by "@" indicates the domain name. l The domain name for user login cannot exceed 15 characters, and the other domain names cannot exceed 20 characters.

  • Page 275: Configuring Docsis Event Reporting

    Default mode of reporting DOCSIS events with information or debugging priorities: not reported ----End Example The following is an example of the configurations used to enable the CM management feature: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 276 Mode of reporting DOCSIS events to the log host: syslog IP address of the U2000: 10.10.10.10 IP address of the log host: 10.10.20.10 huawei(config)#cable event alert report trap huawei(config)#snmp-agent target-host trap-hostname huawei address 10.10.10.10 trap-paramsname docsis huawei(config)#cable event alert report syslog huawei(config)#cable event loghost ip 10.10.20.10...

  • Page 277: Configuring The Dslam Services

    This topic describes how to configure the H.248-based, MGCP-based, and SIP-based VoIP services respectively. 3.4 Example: Configuring the Triple Play This topic describes how to configure the Triple Play on the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 278: Example: Configuring The Xdsl Internet Access Service

    Figure 3-1 Example network of the xDSL Internet access service through the PPPoE dialup Prerequisite The AAA function must be configured. – To enable the AAA function on the device, see 2.4 Configuring AAA. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 279 LACP static mode, do as follows: huawei(config)#link-aggregation 0/19 0 0/19 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
  • Page 280 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
  • Page 281 S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on SHDSL port 0/3/1. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode ptm 0/3/1 inbound traffic- table index 5 outbound traffic-table index 5...
  • Page 282 Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay 8 2 inp 4 2 rate 128 10000 128 10000 2048 2048...
  • Page 283 PPPoE emulation dialing task initiated by the user. Configuration File Configuration File in the ADSL access mode: vlan 50 smart vlan attrib 50 stacking Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 284 3 description Vlanid:50/vdsl/vpi:1vci:39/stacking stacking label service-port 3 10 stacking inner-priority service-port 3 4 stacking inner-priority service-port 2 4 pitp enable pmode raio-mode cntel pitp-pmode save Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 285: Example: Configuring The Xdsl Ipoe Internet Access Service

    Figure 3-2 Example network of the xDSL IPoE Internet access service Prerequisite The user PC can obtain an IP address from the DHCP server. Procedure Step 1 Configure a VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 286 LACP static mode, do as follows: huawei(config)#link-aggregation 0/19 0 0/19 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
  • Page 287 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
  • Page 288 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay 8 2 inp 4 2 rate...
  • Page 289 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/4/1. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/4/1 inbound traffic- table index 5 outbound traffic-table index 5...
  • Page 290 0 1 quit service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5 service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/stacking Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 291 3 10 stacking inner-priority service-port 3 4 stacking inner-priority service-port 2 4 dhcp option82 enable raio-mode user-defined dhcp-option82 raio-format dhcp-option82 cid anid frame/slot/port:vlanid raio-format dhcp-option82 rid splabel save Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 292: Example: Configuring The Xdsl Pppoa Internet Access Service

    Internet access must be configured on the BRAS. Procedure Step 1 Create a VLAN. Create smart VLAN 50. huawei(config)#vlan 50 smart Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 293 ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin is 6 dB. huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120 huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate...
  • Page 294 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5...
  • Page 295 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/3/1 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5...
  • Page 296 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/4/1 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5...
  • Page 297 Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config)#encapsulation 0/3/1 vpi 1 vci 39 type pppoa llc huawei(config)#encapsulation 0/4/1 vpi 1 vci 39 type pppoa llc Step 7 Configure the user account security. The PITP P mode can be enabled to protect the user account against theft and roaming. The RAIO mode can be customized according to actual requirements.

  • Page 298: Example: Configuring The Xdsl Ipoa Internet Access Service

    (ATM) network to the IP network. An authentication is generally not required for IPoA users. Service Requirements The user accesses the Internet in the IPoA mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 299 LACP static mode, do as follows: huawei(config)#link-aggregation 0/19 0 0/19 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
  • Page 300 Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5...
  • Page 301 SHDSL line profile is 3, the line rate is 2048 kbit/s, and the profile is used to activate 4-wire ports. huawei(config)#shdsl line-profile quickadd 3 line four-wire rate 2048 Activate the SHDSL port. The port is port 0/3/1, and SHDSL line profile 3 and the default alarm profile (alarm profile 1) are bound to the port.
  • Page 302 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/3/1 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 2 description MA5600T/MA5603T/MA5608THW/ Vlanid:50/shdsl/smart Set the maximum number of MAC addresses that can be learned by the service port is 16.
  • Page 303 VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1 and 39. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/4/1 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5...
  • Page 304 3 vlan 50 vdsl mode atm 0/4/1 vpi 1 vci 39 inbound traffic-table index 5 outbound traffic-table index 5 service-port desc 3 description MA5600T/MA5603T/MA5608THW/Vlanid:50/vdsl/smart mac-address max-mac-count service-port 3 16 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 305: Example: Configuring The Internet Access Service In The Xdsl 802.1X Mode

    Configure S-VLAN 50 with the stacking attribute. The user packet goes upstream carrying two VLAN tags. The outer VLAN tag identifies the service and the inner VLAN tag identifies the Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 306 LACP static mode, do as follows: huawei(config)#link-aggregation 0/19 0 0/19 1 egress-ingress workmode lacp-static NOTE The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type;...
  • Page 307 VPI and VCI of the modem are 1 and 39, and the access port ID is 0/2/0. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic- table index 5 outbound traffic-table index 5 huawei(config)#service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/ stacking Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user.
  • Page 308 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum upstream INP is 2. huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300 huawei(config)#vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay 8 2 inp 4 2 rate...
  • Page 309 S-VLAN ID to 50. Set the VDSL channel mode to PTM, and create service port 3 on VDSL port 0/4/1. To facilitate the maintenance of the service port, also configure the service port description. huawei(config)#service-port 3 vlan 50 vdsl mode ptm 0/4/1 inbound traffic- table index 5 outbound traffic-table index 5...
  • Page 310 Create a local user with the user name shenzhen and the password shenzhen. huawei(config-aaa)#local-user shenzhen@huawei service-type terminal password shenzhen Name the AAA domain huawei. Bind the domain with the accounting scheme named huawei, authentication scheme named huawei. huawei(config-aaa)#domain huawei huawei(config-aaa-domain-huawei)#authentication-scheme huawei...
  • Page 311 1 interval 20 service-port 1 dot1x eap-end service-port 1 authentication-scheme huawei authentication-mode local quit accounting-scheme huawei accounting-mode none quit local-user shenzhen@huawei service-type terminal password shenzhen domain huawei authentication-scheme huawei accounting-scheme huawei quit quit save Configuration File of the SHDSL access mode:...
  • Page 312 1 interval 20 service-port 2 dot1x eap-end service-port 2 authentication-scheme huawei authentication-mode local quit accounting-scheme huawei accounting-mode none quit local-user shenzhen@huawei service-type terminal password shenzhen domain huawei authentication-scheme huawei accounting-scheme huawei quit quit save Configuration File of the VDSL access mode:...

  • Page 313: Configuration Example Of Changing Adsl Internet Access Service To Vdsl Internet Access Service (For The Vdsl2 Board)

    Step 1 Confirm the line template bound to a port that needs such service modifications, for example, port 0/2/4. Run the display port state command to query the line template bound to the port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 314 According to actual conditions over the live network, SNR is planned to 7 dB, transmission mode to all (its value is 1), and line profile index to 11. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 315 Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config-if-vdsl-0/2)#vdsl line-profile quickadd 11 transmode 1 snr 70 0 300 70 0 300 All parameters following vdsl-parameter are VDSL parameters in contrast to ADSL. These parameters do not need to be configured in the case of the ADSL Internet access service.
  • Page 316 Generally, the ADSL is in the ATM mode and the VDSL is in the PTM mode. If an ATM service port only is configured, a PTM service port needs to be added. huawei(config)#service-port 3 vlan 101 vdsl mode ptm 0/2/4 rx-cttr 7 tx-cttr 7 huawei(config)#service-port desc 3 description Vlanid:101/vdsl/ptm Step 9 Save the data.

  • Page 317: Example: Configuring The Xdsl Multicast Service

    5 Mbit/s. Bandwidth restriction is required for the two users. Figure 3-7 shows an example network of the multicast service. User 1 and user 2 are connected to the MA5600T/MA5603T/MA5608T in VDSL IPoE mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 318 Multicast domain of ISP 2: VLAN 20 NOTE It is recommended that different multicast VLANs be planned for different ISPs. Multicast upstream port 0/19/0 Multicast mode IGMP proxy Multicast protocol IGMPv3 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 319 Step 1 Configure multicast VLANs and programs. Configure smart VLAN 10 as the multicast domain of ISP 1, and smart VLAN 20 as the multicast domain of ISP 2. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 320 3500 kbit/s, and enable program log reporting. huawei(config)#vlan 10 smart huawei(config)#multicast-vlan 10 huawei(config-mvlan10)#igmp mode proxy huawei(config-mvlan10)#igmp uplink-port 0/19/0 huawei(config-mvlan10)#igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 bandwidth 3500 log enable huawei(config-mvlan10)#igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.10...
  • Page 321 Create service port 100 on VDSL port 0/2/1, and service port 101 on VDSL port 0/4/1. huawei(config)#port vlan 10 0/19 0 huawei(config)#port vlan 20 0/19 0 huawei(config)#service-port 100 vlan 10 vdsl mode ptm 0/2/1 rx-cttr 2 tx-cttr huawei(config)#service-port 101 vlan 20 vdsl mode ptm 0/4/1 rx-cttr 2 tx-cttr Configure the attributes of the multicast users.

  • Page 322: Configuration Example Of The Multicast Video Service (Dynamic Program Generation)

    The service package purchased by user 2 allows user 2 to watch programs of ISP 2 only. The ordering information about users can be recorded for monitoring and charging. Figure 3-8 shows an example network of the multicast service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 323 Multicast domain of ISP 2: VLAN 20 NOTE It is recommended that different multicast VLANs be planned for different ISPs. Multicast upstream port 0/19/0 Multicast mode IGMP proxy Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 324 Therefore, it is recommended that the program configuration mode be planned beforehand. huawei(config)#vlan 10 smart huawei(config)#multicast-vlan 10 huawei(config-mvlan10)#igmp match mode disable huawei(config-mvlan10)#igmp match group ip 224.1.1.1 to-ip 224.1.1.2 huawei(config-mvlan10)#igmp uplink-port 0/19/0 huawei(config-mvlan10)#igmp mode proxy huawei(config-mvlan10)#quit Configure the protocol, multicast upstream port, and program list of multicast VLAN 20.
  • Page 325 Create service port 100 on VDSL port 0/2/1, and service port 101 on VDSL port 0/4/1. huawei(config)#port vlan 10 0/19 0 huawei(config)#port vlan 20 0/19 0 huawei(config)#service-port 100 vlan 10 vdsl mode ptm 0/2/1 rx-cttr 2 tx-cttr huawei(config)#service-port 101 vlan 20 vdsl mode ptm 0/4/1 rx-cttr 2 tx-cttr Configure the attributes of the multicast users.

  • Page 326: Example: Configuring The Voip Service

    The common phone services are provisioned to 32 users (phones 0-31). The polarity-reversal accounting is adopted. Figure 3-9 shows an example network for configuring the H.248-based VoIP service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 327 MGC and according to the data plan described in Configuring the VoIP Service (H.248-based or MGCP-based). Table 3-3 provides the data plan for configuring the H.248-based VoIP service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 328 32 users to be provisioned with the services are the interface first batch of users in the community named huawei, and later other users in NOTE this community will be provisioned Parameter s listed with the same services gradually.
  • Page 329 To differentiate users according to the MG interface TID, the service provider requires that the terminal prefix uses the community name huawei and the TID is automatically generated by the system according to the slot ID/subrack ID/port ID of the user.
  • Page 330 According to the data plan, configure standard VLAN 20 as the media and signaling upstream VLAN, add upstream port 0/19/0 to the VLAN, and configure the IP address of the Layer 3 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 331 Step 5 Configure the TID format of PSTN users on MG interface 0. Configure the TID generation mode. According to the data plan, the terminal prefix of PSTN users needs to be huawei, and the TID template adopts layering template 6. NOTICE The MA5600T/MA5603T/MA5608T requires that the terminal prefixes of PSTN users, ISDN BRA users, and ISDN PRA users on the same H.248 interface are either the same or different.
  • Page 332 Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config-if-h248-0)#tid-format pstn prefix huawei template 6 Step 6 Enable the MG interface. Reset the MG interface to make the MG interface register with the MGC (or to make the attributes of the MG interface take effect), so that the MG interface can work in the normal state.
  • Page 333 0 0 4 Configure the TID format of the PSTN user on the MG interface. tid-format pstn prefix huawei template 6 Enable the MG interface. The MG interface must be enabled manually, and the configuration profile cannot be directly imported.

  • Page 334: Example: Configuring The Voip Service (Mgcp-Based)

    IP address pool must be the same. When the H.248 or SIP protocol is used, the media IP address pool and the signaling IP address pool can be the same or different. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 335 32 users to be provisioned with the services are the interface first batch of users in the community named huawei, and later other users NOTE will be provisioned with the same Parameter s listed services gradually.
  • Page 336 To differentiate users according to the MG interface TID, the service provider requires that the terminal prefix uses the community name huawei and the TID is automatically generated by the system according to the slot ID/subrack ID/ port ID of the user.
  • Page 337 There is no special requirement, and the configuration of the ringing current attributes is not required. Figure 3-10 shows an example network for configuring the MGCP-based VoIP service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 338 The POTS service board, namely the ASPB board, must be inserted into the planned slot, and the RUN ALM LED of the board must be green and must be on for 1s and off for 1s repeatedly. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 339 Step 5 Configure the TID format of PSTN users on MG interface 0. Configure the TID generation mode. According to the data plan, the terminal prefix of PSTN users needs to be huawei, and the TID template adopts layering template 6. huawei(config-if-mgcp-0)#tid-format pstn prefix huawei template 6 Step 6 Enable the MG interface.
  • Page 340 Configure the physical attributes of the PSTN port to which the users belong to support the polarity reversal pulse, so that the users can support the polarity reversal accounting. huawei(config)#pstnport huawei(config-pstnport)#pstnport attribute batset 0/3/0 0/3/31 reverse-pole-pulse enable huawei(config-pstnport)#quit Step 10 Save the data.

  • Page 341: Example: Configuring The Voip Pstn Service (Sip)

    Configure the ringing mapping of the MG interface. mg-ringmode add 0 0 4 Configure the TID format of the PSTN user on the MG interface. tid-format pstn prefix huawei template 6 quit Enable the MG interface. The MG interface must be enabled manually, and the configuration profile cannot be directly imported.
  • Page 342 Port ID of the primary parameter softswitch to s, and the which the SIP parameter interface belongs s here are mandator Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 343 64-Phone 127 User type Payphone PSTN port Polarity reversal pulse supported attributes Figure 3-11 shows an example network of the VoIP PSTN service (SIP). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 344 VLAN, add upstream port 0/19/0 to the VLAN, and configure the IP address of the Layer 3 interface to 10.10.10.10, which facilitates the configuration of the media and signaling IP address pools. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 345 Transfer mode: UDP l IP address of the primary IMS: 10.10.10.20 l Signaling port ID of the primary IMS: 5060 l Homing domain name of SIP interface: huawei l SIP profile ID: 1 huawei(config)#interface sip 0 Are you sure to add SIP interface?(y/n)[n]:y huawei(config-if-sip-0)#if-sip attribute basic media-ip 10.10.10.10...
  • Page 346 Step 7 Configure the PSTN subscriber data. Configure the PSTN user data (Phone 0-Phone 63) in slot 0/2. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/2/0 0/2/63 0 telno 83110000 Configure the calling priority of the PSTN user in port 0/2/0 as Cat2. huawei(config-esl-user)#sippstnuser attribute set 0/2/0 priority cat2 Configure the PSTN user data (Phone 64-Phone 127) in slot 0/3.
  • Page 347 Add an SIP interface and configure the attributes of the SIP interface. if-sip attribute basic media-ip 10.10.10.10 signal-ip 10.10.10.10 signal-port 5060 transfer udp primary-proxy-ip1 10.10.10.20 primary-proxy-port 5060 home-domain huawei sipprofile-index 1 Configure the ringing mapping of the SIP interface. ringmode add 0 ringname cadencering 0 initialring 4 Enable the SIP interface.

  • Page 348: Example: Configuring The Voip Service (H.248-Based And Sip-Based)

    After the configuration is completed, normal calls can be made between two phone sets. Figure 3-12 shows an example network of the VoIP service that based the SIP protocol and H. 248 protocol. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 349 The ISDN digital phone must support the P2P function. The terminal endpoint identifier of the ISDN digital phone must be 0. Data Plan Table 3-6 provides the data plan . Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 350 MGC that is primary-mgc bound to the IUA link Priority of the IUA link. ISDN BRA port Subrack ID/ 0/2/0 Slot ID/Port ID IUA interface Working mode Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 351 1 mgid 0 jointly-work enable trafficmode override iid-map 2 pendingtime 1 cs-mode client huawei(config-sigtran)#iua-link add 15 1 1401 10.13.4.116 1400 10.14.1.2 jointly-work-with primary-mgc priority 3 huawei(config-sigtran)#quit NOTE All the ISDN call control messages are sent from the IUA link to the softswitch, whereas the system uses the bearer control messages to communicate with the softswitch through H.248.
  • Page 352 Configure the PSTN subscriber data. According to the data plan, configure a telephone number and priority of the PSTN user. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/1 0 telno 83110000 huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 huawei(config-esl-user)#sippstnuser attribute set 0/3/1 priority cat2 huawei(config-esl-user)#quit Configure the PSTN port attributes.

  • Page 353: Example: Configuring The P2P Isdn Bra Service

    MA5608T to provide a rate of 144 kbit/s, including two B channels and one D channel. After the configuration is completed, normal calls can be made between two phone sets. Figure 3-13 shows an example network of the P2P ISDN BRA service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 354 P2P ISDN BRA service. Table 3-7 Data plan for configuring the P2P ISDN BRA service Item Data MG interface ID IUA link set IUA link set ID parameter Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 355 10.14.1.2/16 (IP address of the primary MGC) the primary ISDN BRA port Subrack ID/ 0/2/0, 0/3/0 Slot ID/Port ID IUA interface 8, 9 Working mode 100, 110 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 356 H.248. Step 3 Configure the ISDN BRA user data. huawei(config)#esl user huawei(config-esl-user)#mgbrauser add 0/2/0 0 1 interfaceid 8 terminalid 100 telno 12345601 huawei(config-esl-user)#mgbrauser add 0/3/0 0 1 interfaceid 9 terminalid 110 telno...

  • Page 357: Example: Configuring The P2P Isdn Bra Service (Based On The Sip Protocol)

    MA5608T, which is applicable to the scenario where one NT1 is connected to only one terminal. Service Requirements ISDN Phone A is connected to the MA5600T/MA5603T/MA5608T through the NT1, and the ISDN digital phone supports the P2P function. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 358 The system must be configured with the ISDN service board, that is, the DSRD board or the DSRE board . The terminal endpoint identifier of the ISDN digital phone must be 0. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 359 In the BRA port mode, configure the working mode of the ISDN BRA port to P2P, configure the activation mode to stable activation, and disable automatic activation. huawei(config)#braport huawei(config-braport)#braport attribute set 0/2/0 workmode p2p activemode stable- active autodeactive disable huawei(config-braport)#braport attribute set 0/3/0 workmode p2p activemode stable-...

  • Page 360: Example: Configuring The P2Mp Isdn Bra Service

    Configuring an MG Interface and (Optional) Configuring the System Parameters. The MG interface must be in the normal state. Networking Figure 3-15 shows an example network of the P2MP ISDN BRA service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 361 Working mode of override a link set Pending time Mode of generating the interface ID Whether the link enable in the link set supports the interlocking Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 362 In the SIGTRAN mode, configure the SIGTRAN protocol stack. Add an IUA link set, and then add IUA links. huawei(config-braport)#quit huawei(config)#sigtran huawei(config-sigtran)#iua-linkset add 1 mgid 0 jointly-work enable trafficmode override Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 363: Example: Configuring The P2Mp Isdn Bra Service(Based On The Sip Protocol)

    15 1 1401 10.13.4.116 1400 10.14.1.2 jointly-work-with primary-mgc priority 3 Step 3 Configure the ISDN BRA user data. huawei(config-sigtran)#quit huawei(config)#esl user huawei(config-esl-user)#mgbrauser add 0/3/1 0 1 interfaceid 10 terminalid 106 telno 88880000 Step 4 Save the data. huawei(config-esl-user)#quit huawei(config)#save...
  • Page 364 P2MP ISDN BRA service. Table 3-10 Data plan for the P2MP ISDN BRA service Item Data MG interface ID ISDN BRA port Subrack ID/Slot 0/3/1 ID/Port ID Working mode P2MP Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 365: Example: Configuring The Isdn Pra Service

    In the BRA port mode, configure the working mode of the ISDN BRA port to P2MP, configure the activation mode to stable activation, and enable automatic activation. huawei(config)#braport huawei(config-braport)#braport attribute set 0/3/1 workmode p2mp autodeactive enable huawei(config-braport)#quit Step 2 Configure the ISDN BRA user data.
  • Page 366 Table 3-11 provides the data plan for configuring the ISDN PRA service. Table 3-11 Data plan for configuring the ISDN PRA service Item Data MG interface ID Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 367 0/2/0 ID/Port ID IUA interface ID Procedure Step 1 Add the EDTB board. According to the data plan, add an ISDN PRA service board to slot 0/2. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 368 Step 3 Configure the ISDN PRA user data. huawei(config-sigtran)#quit huawei(config)#esl user huawei(config-esl-user)#mgprauser add 0/2/0 0 1 interfaceid 1 terminalid 512 NOTICE Each ISDN PRA user occupies 32 TIDs. You need to input only the first TID when adding an ISDN PRA user.

  • Page 369: Example: Configuring The Isdn Pra Service (Based On The Sip Protocol)

    After the configuration is completed, users of the PBX can make calls successfully and can communicate with users outside the PBX in the normal state. Networking Figure 3-18 shows an example of the ISDN PRA service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 370 ISDN PRA port Subrack ID/Slot 0/2/0 ID/Port ID Phone number 12345600 Procedure Step 1 Configure the ISDN PRA user data. huawei(config)#esl user huawei(config-esl-user)#sipprauser add 0/2/0 0 telno 12345600 huawei(config-esl-user)#quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 371: Example: Configuring Tdm Shdsl For Carrying The Pra Service

    Figure 3-19 Example network of TDM SHDSL for carrying the PRA service Data Plan The following table lists the data plan for configuring TDM SHDSL for carrying the PRA service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 372 PRA user interface data MGID: 0 IUA link set ID: 0 Terminal ID: 0 Prerequisite The H802EDTB board must be in position and must work in the normal state. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 373 In the SIGTRAN mode, configure the SIGTRAN protocol stack. Add an IUA link set, and then add IUA links. huawei(config)#sigtran huawei(config-sigtran)#iua-linkset add 1 mgid 0 jointly-work enable trafficmode override iid-map 2 pendingtime cs-mode client huawei(config-sigtran)#iua-link add 15 1 1401 10.13.4.116 1400 10.14.1.2...

  • Page 374: Example: Configuring Tdm Shdsl For Carrying The Pra Service (Based On The Sip Protocol)

    0 shdslport signal 16 CCS quit huawei(config)#sigtran huawei(config-sigtran)#iua-linkset add 1 mgid 0 jointly-work enable trafficmode override iid-map 2 pendingtime cs-mode client huawei(config-sigtran)#iua-link add 15 1 1401 10.13.4.116 1400 10.14.1.2 jointly-work-with primary-mgc priority 3 esl user...
  • Page 375 Configure the signaling mode of SHDSL port 0/3/16 to CCS. PRA D channel signaling is transmitted in timeslot 16 and timeslot 0 is used for frame synchronization. huawei(config-edt-0/3)#shdslport signal 16 CCS huawei(config-edt-0/3)#quit Step 5 Configure a PRA user. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 376: Configuring Vags

    SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 3 Configuring the DSLAM Services huawei(config)#esl user huawei(config-esl-user)#sipprauser add 0/3/16 0 telno 12345600 huawei(config-esl-user)#quit Step 6 Save the data. huawei(config)#save ----End Result The phone set connected to the PBX can communicate with a phone set in the PSTN network in the normal state.
  • Page 377 MG0 indicates VAG1 in the figure, and MG1 indicates VAG2 in the figure. Networking Figure 3-21 shows an example network of the VAG service. Figure 3-21 Example network of the VAG service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 378 Coding mode of text (indicates the text coding mode) s are not the MG interface configure Transmission mode of the MG interface Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 379 To differentiate users according to the Format of an MG Interface TID, the office requires that the terminal prefix uses the community name huawei and the TID is automatically generated by the system according to the subrack ID/slot ID/port ID (F/S/P) of the user.
  • Page 380 Configure the TID template of the PSTN users on MG interface 0. Configure the TID generation mode. According to the data plan, the terminal prefix of PSTN users is huawei, and the TID template adopts layering template 6. NOTICE The MA5600T/MA5603T/MA5608T requires that the terminal prefixes of PSTN users, ISDN BRA users, and ISDN PRA users on the same H.248 interface be either...
  • Page 381 Configure the TID template of the PSTN users on MG interface 1. Configure the TID generation mode. According to the data plan, the terminal prefix of PSTN users is huawei, and the TID template adopts layering template 6. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright ©...
  • Page 382 ISDN BRA users, and ISDN PRA users on the same H.248 interface be either the same or different. Note this when configuring the terminal prefix. huawei(config-if-h248-1)#tid-format pstn prefix huawei template 6 Reset the MG interface. Reset the MG interface to make the MG interface register with the MGC (and to make the modified attributes of the MG interface take effect) so that the MG interface can work in the normal state.

  • Page 383: Example: Configuring The Sip-Based Vag Service

    – Local IP address – Local port ID – Remote IP address – Remote port ID Service Requirements Figure 3-22 shows an example network of the SIP-based VAG service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 384 – The IMS assigns phone numbers 85000000-85000031 to phones 0-31 of VAG2. SIP interface 0 indicates VAG1 in the figure, and SIP interface 1 indicates VAG2 in the figure. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 385 SIP interface Voice user data Slot of the voice service board The ASPB service board in slot 0/2 and 0/3. (The data configuration Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 386 Reset the SIP interface to make the SIP interface register with the IMS (and to make the modified attributes of the SIP interface take effect) so that the SIP interface can work in the normal state. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 387 0/2 Configure the PSTN user data. Add POTS users (phones 0-31) to VAG1 so that the users can go online. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/2/0 0/2/31 0 telno 80000000 huawei(config-esl-user)#quit Save the data. huawei(config)#save Configure VAG2.

  • Page 388: Example: Configuring The Triple Play

    0/3 Configure the PSTN user data. Add POTS users (phones 0-31) to VAG2 so that the users can go online. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/31 1 telno 85000000 huawei(config-esl-user)#quit Save the data. huawei(config)#save ----End...
  • Page 389 The different services have different request on the bandwidth and priority. Because the bandwidth and delay of the VoIP service are low, the priority of the VoIP service is the highest among the triple play services. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 390: Configuration Example Of The Triple Play (Multi-Pvc For Multiple Services)

    Service Requirements ADSL2+ user 1 and ADSL2+ user 2 are connected to the MA5600T/MA5603T/MA5608T to implement the triple play. The PC user accesses the Internet properly. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 391 Figure 3-23 Example network of the triple play service in the multi-PVC for multiple services mode Data Plan Table 3-17 shows the key data for configuring the triple play in multi-PVC for multiple services mode on the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 392 VPI: 0 l Index: 100 and 101 The three port services have l VCI: 37 l VCI: 36 l VPI: 0 different l VCI: 35 VCIs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 393 0/19/0 l Multicast IP address of program BTV-1: 224.1.1.1; program source IP address: 10.10.10.10 l Multicast IP address of program BTV-2: 224.1.1.2; program source IP address: 10.10.10.10 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 394 Add a service port to the VLAN 2 and use the traffic profile 7 added in the preceding step. huawei(config)#service-port vlan 2 adsl 0/2/1 vpi 0 vci 37 rx-cttr 7 tx- cttr 7 huawei(config)#service-port vlan 2 adsl 0/3/1 vpi 0 vci 37 rx-cttr 7 tx- cttr 7 Save the data.
  • Page 395 PVC does not take effect. Add a service port to VLAN 4 and use traffic profile 9. huawei(config)#service-port 100 vlan 4 adsl 0/2/1 vpi 0 vci 35 rx-cttr 9 tx-cttr 9 huawei(config)#service-port 101 vlan 4 adsl 0/3/1 vpi 0 vci 35 rx-cttr 9 tx-cttr 9 Configure the DHCP relay.
  • Page 396 BTV-1 ip 224.1.1.1 sourceip 10.10.10.10 igmp program add name BTV-2 ip 224.1.1.2 sourceip 10.10.10.10 igmp profile profile-name profile0 program-name BTV-1 watch igmp policy service-port 100 normal igmp policy service-port 101 normal Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 397: Configuration Example Of The Triple Play (Single-Pvc For Multiple Services) - Stream-Based Rate Limitation

    The Internet service is accessed in the PPPoE mode. The VoIP service and the IPTV service are provided in the DHCP mode, obtaining IP addresses from the DHCP server in the standard DHCP mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 398 Ephone User 2 User 1 Data Plan Table 3-18 shows the key data for configuring the triple play in single-PVC for multiple services mode on the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 399 VPI: 0 l Index: 100 and 101 The three port services have l VCI: 35 l VCI: 35 l VPI: 0 different l VCI: 35 VCIs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 400 0/19/0 l Multicast IP address of program BTV-1: 224.1.1.1; program source IP address: 10.10.10.10 l Multicast IP address of program BTV-2: 224.1.1.2; program source IP address: 10.10.10.10 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 401 2 smart huawei(config)#port vlan 2 0/19 0 Add a traffic profile. huawei(config)#traffic table ip index 7 cir 2048 priority 1 priority- policy local-Setting Add a service port to the VLAN. Add a service port to VLAN 2 and use the traffic profile added 7 in the preceding step.
  • Page 402 PVC does not take effect. Add a service port to VLAN 4 and use traffic profile 9. huawei(config)#service-port 100 vlan 4 adsl 0/2/1 vpi 0 vci 35 multi- service user-vlan 40 rx-cttr 9 tx-cttr 9...
  • Page 403 9 tx-cttr 9 dhcp mode layer-3 standard dhcp-server 2 ip 20.2.2.2 20.2.2.3 interface vlanif 4 ip address 10.2.2.1 24 dhcp-server 2 quit multicast-vlan 4 igmp mode proxy Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 404: Configuration Example Of The Triple Play Service (Single-Pvc For Multiple Services) - User-Based And Stream-Based Rate Limitation

    (the value is 6), IPTV (the value is 5), and Internet access (the value is 1) in descending order. If any two services carry no traffic, the third service can hold a burst of the total user bandwidth. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 405 Router VoIP DHCP IP1:20.1.1.2 BRAS Server IP2:20.1.1.3 Access node Home Gateway 2 DHCP PPPoE DHCP Home Gateway 1 DHCP PPPoE DHCP Ephone Ephone User 2 User 1 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 406 SVLAN ID: 3 l SVLAN ID: 4 l SVLAN type: l SVLAN type: l SVLAN type: smart smart smart l CVLAN ID: l CVLAN ID: l CVLAN ID: 40 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 407 DHCP server group 2: 20.2.2.3 group 2: l IP address of the 20.1.1.3 VLAN Layer 3 l IP address of interface: the VLAN 10.2.2.1/24 Layer 3 interface: 10.1.1.1/24 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 408 32 kbit/s, a minimum upstream/downstream reserved rate 32 kbit/s, a maximum downstream transmission rate 10240 kbit/s and a maximum upstream transmission rate 4096 kbit/s. huawei(config)#adsl channel-profile quickadd 3 rate 32 32 10240 32 32 4096 Configure ADSL line template 3 by binding channel profile 3.
  • Page 409 Create a VLAN and add an upstream port to the VLAN. huawei(config)#vlan 2 smart huawei(config)#port vlan 2 0/19 0 Configure a traffic profile. huawei(config)#traffic table ip index 7 cir 2048 pir 10240 priority 1 priority- policy local-Setting Add a service port to the VLAN.
  • Page 410 Create a VLAN and add an upstream port to the VLAN. huawei(config)#vlan 4 smart huawei(config)#port vlan 4 0/19 0 Configure a traffic profile. huawei(config)#traffic table ip index 9 cir 4096 pir 10240 priority 5 priority-policy local-Setting Add a service port to the VLAN. NOTICE On the MA5600T/MA5603T/MA5608T, if the PVC is configured with a priority, the priority of the multicast packets carried by the PVC does not take effect.
  • Page 411 0 vci 35 multi-service user-vlan 30 rx-cttr 8 tx-cttr 8 dhcp mode layer-3 standard dhcp-server 1 ip 20.1.1.2 20.1.1 3 interface vlanif 3 ip address 10.1.1.1 24 dhcp-server 1 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 412 101 auth igmp user bind-profile service-port 100 profile-name profile0 multicast-vlan 4 igmp multicast-vlan member service-port 100 igmp multicast-vlan member service-port 101 quit save Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 413: Configuration Example Of The Private Line Service

    MA5603T/MA5608T transparently transmits user-side configuration data to the digital data network (DDN). In this way, the twisted pair can be fully used and the E1 line deployment expense decreases. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 414 E1 line, and therefore can share the bandwidth of the E1 line, hence saving the E1 line lease expense. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 415: Example: Configuring The Qinq Vlan

    In this way, the service packets of the enterprise private network can be transparently transmitted through the public network, and the two branches can communicate with each other securely. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 416 QinQ VLAN. Data Plan Table 4-1 lists the key data planning of the QinQ VLAN private line service on MA5600T/ MA5603T/MA5608T_A. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 417 VCI: 35 requirement is used. l ID of the traffic profile in Rx direction: l ID of the traffic profile in Tx direction: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 418 The VPI and the VCI are 0 and 35 respectively, the same as those on the peer modem. The user port is 0/2/0. The VDSL channel is in ATM mode. huawei(config)#service-port vlan 50 vdsl mode atm 0/2/0 vpi 0 vci 35 rx-cttr 10 tx- cttr 10 Step 8 Save the data.

  • Page 419: Example: Configuring Vlan Stacking Multi-Isp Wholesale Access

    Layer 2 network. Then the Layer 2/Layer 3 LAN switch forwards the user packets to the specified ISP BRAS based on the outer VLAN tag. The ISP BRAS Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 420 Data Plan Table 4-2 lists the key data planning of the VLAN stacking wholesale service on the MA5600T/ MA5603T/MA5608T. The ADSL2+ access is used as an example. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 421 VPI: 0 l VCI: 35 l ID of the traffic profile in Rx direction: 10 l ID of the traffic profile in Tx direction: 10 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 422 1 vlan 60 adsl 0/2/1 vpi 0 vci 35 rx-cttr 10 tx-cttr huawei(config)#service-port 2 vlan 61 adsl 0/3/0 vpi 0 vci 35 rx-cttr 10 tx-cttr huawei(config)#service-port 3 vlan 61 adsl 0/3/1 vpi 0 vci 35 rx-cttr 10 tx-cttr 10 Step 7 Set the inner VLAN tags.

  • Page 423: Configuration Example Of The Pwe3 Private Line Service

    3 12 save 4.3 Configuration Example of the PWE3 Private Line Service This topic describes how to configure the MPLS PWE3 private line service using examples. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 424: Example: Configuring Atm Pwe3 To Implement Migration From Atm Network To Ip Network

    ATM BRAS remains. ATM service data is transparently transmitted across the network. The quality of service (QoS) such as traffic and priority, can be guaranteed for real-time ATM services. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 425 (the host route of each port must be successfully advertised). Context For the principle and configuration of trTCM by CoS remarking, see Configuring PW-based trTCM by CoS Remarking. The following ATM service types are available: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 426 ATM cells. In this way, the transmission PW type: static efficiency of ATM cells over a PSN network and bandwidth utilization are improved. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 427 ISP, the VPI/VCI parameters Cells of cells on PVCs at different ports are the same. Bindin Services of different types are g PW carried over different PWs, eliminating service interaction. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 428 WRED ID: 5 ID: 5 ID: 5 QoS policies: Profile In the downstream direction, the xDSL board sets CoS drop threshold globally to early drop yellow packets. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 429 PWE3 has no special requirement for the routing policy. Either a static route or an OSPF dynamic route can be configured. Because OSPF supports MPLS RSVP-TE extension, an OSPF dynamic route is recommended. huawei(config)#ospf 1 huawei(config-ospf-1)#area 200 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 430 For UBR services, set the upstream/downstream traffic profile to 20, CIR to off (limiting rate only on BRAS), color policy to CoS, user-side packet mapping mode to outer-layer 802.1p, default 802.1p to 1, and priority policy to tag-in-package. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 431 PWs. This ensures that the VPI/VCI parameters are unique for cells on each PVC in the PW. l Bind PVCs and PWs in batches for UBR services. huawei(config)#multi-pw-ac-binding pvc board 2 vpi 0 vci 35 from-outvpi 0 outvci from-invpi 1 invci 32 pw 20 static transmit-label 8450 receive-label 8460 l Bind PVCs and PWs in batches for VBR services.
  • Page 432 0 yellow low-limit 50 high-limit 80 discard-probability 100 Step 11 Configure queues and bind the WRED profile. huawei(config)#queue-wred queue0 5 queue1 5 queue2 5 queue3 5 queue4 5 queue5 5 queue6 5 queue7 5 Step 12 Configure the priority remarking policy.

  • Page 433: Example: Configuring The Atm Pwe3 To Achieve Emulated Atm Services On The Mpls Network

    ATM network evolves to the MPLS network, PWE3 encapsulation is recommended. Service Requirements The xDSL service board (or AIUG board) of the MA5600T/MA5603T/MA5608T is used to provide the ATM service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 434 ATM PWE3 (MPLS-based). Figure 4-4 Example network of the ATM PWE3 (MPLS-based) Data Plan Table 4-5 lists the data plan for configuring the ATM PWE3 (MPLS-based). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 435 Step 1 Configure a VLAN and add an upstream port to the VLAN. Create upstream VLAN 300 and add upstream port 0/19/1 to VLAN 300. huawei(config)#vlan 300 standard huawei(config)#port vlan 300 0/19 1 Step 2 Enable MPLS. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 436 Configure the signaling protocol of the MPLS TE tunnel to RSVP-TE. huawei(config-if-tunnel20)#mpls te signal-protocol rsvp-te Configure the MPLS TE tunnel for being bound by a VPN instance. huawei(config-if-tunnel20)#mpls te reserved-for-binding Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 437 The service board is in slot 0/2, VPI/VCI is 0/35, and the traffic profile for the upstream and downstream directions is 20. huawei(config)#multi-service-port vlan aoe board 2 vpi 0 vci 35 inbound traffic-table index 20 outbound traffic-table index 20 l Create AOE service streams in batches for VBR services.
  • Page 438 PWs. This ensures that the VPI/VCI parameters are unique for cells on each PVC in the PW. l Bind PVCs and PWs in batches for UBR services. huawei(config)#multi-pw-ac-binding pvc board 2 vpi 0 vci 35 from-outvpi 0 outvci from-invpi 1 invci 32 pw 20 static transmit-label 8450 receive-label 8460 l Bind PVCs and PWs in batches for VBR services.

  • Page 439: Example: Configuring The Eth Pwe3 To Emulate Ethernet Services On The Mpls Network

    Ethernet packet forwarding can be achieved by using the ETH PWE3 technology. In addition, the ETH PWE3 technology can be deployed to achieve high security with low costs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 440 Global MPLS TE: enabled MPLS Layer 2 VPN: enabled VLAN MPLS RSVP-TE: enabled VLAN Standard VLAN for MPLS forwarding: 200 IP address of the VLAN interface: 192.168.1.10 Upstream port: 0/19/0 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 441 Enable the VLAN interface MPLS TE function and configure the IP address of the VLAN interface. huawei(config)#mpls vlan 200 huawei(config)#interface vlanif 200 huawei(config-if-vlanif200)#ip address 192.168.1.10 24 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 442 Info: New tunnel-policy is configured. huawei(config-tunnel-policy-ethpw-plcy)#tunnel binding destination 6.6.6.6 te tunnel 10 huawei(config-tunnel-policy-ethpw-plcy)#quit Step 6 Configure the PW parameters. Configure the PW ID to 10. huawei(config)#pw-para 10 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 443 ETH PWE3 gateway), and then create a service port for translating the CVLAN ID into the VLAN ID of the emulation service. huawei(config)#vlan 3001 huawei(config)#service-port vlan 3001 eth 0/4/0 multi-service user-vlan 20 rx-cttr 6 tx-cttr 6 Step 8 Bind the VLAN to the PW to create the ETH PWE3 service.

  • Page 444: Example: Configuring The Tdm Pwe3 To Emulate Tdm Services On The Ip Network

    ISDN PRI PBX, and transmit the data upstream as IP packets to the DDN network or SDH network. Prerequisite The H802EDTB board and SPUB board are installed and work in the normal state. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 445 TDM PWE3 (IP-based). Table 4-7 Data plan for configuring TDM PWE3 (IP-based) Parameter Data H802EDTB board Board slot: 0/3 E1 port: 0/3/1 SPUB board Board slot: 0/5 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 446 Enable global MPLS. huawei(config)#mpls huawei(config-mpls)#lsp-trigger host //set up an LSP by triggering the LDP through the host address huawei(config-mpls)#quit Enable Layer 2 VPN. huawei(config)#mpls l2vpn Enable global LDP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 447 Set the destination IP address of the tunnel to the LSR ID of the PTN 9.9.9.9. huawei(config-if-tunnel10)#destination 9.9.9.9 huawei(config-if-tunnel10)#quit Step 6 Configure the tunnel policy. Set the policy name to ip_policy. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 448 Set the TDM connection ID to 1, type to PWE3, and ID of the E1 port on the H802EDTB board to 0/3/1. huawei(config)#tdm-connect connectid 1 tdm pwe3-uplink 0/3 e1 0/3/1 Step 9 Bind the TDM connection to the PW to create the PW service of the TDM type.
  • Page 449 10.50.50.50 24 mpls mpls ldp quit ospf 1 area 100 network 10.50.50.0 0.0.0.255 network 3.3.3.3 0.0.0.0 return interface tunnel 10 tunnel-protocol mpls ip destination 9.9.9.9 quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 450: Example: Configuring The Tdm Pwe3 To Emulate Tdm Services On The Mpls Network

    ETH header to the packets, and then sends them to the control board. The control board performs Layer 2 forwarding and sends the packets to the upstream port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 451 VLAN for MPLS forwarding: 4001 IP address of VLAN interface 4001: 10.50.50.50/24 MPLS LSR ID: 3.3.3.3 Global MPLS LDP: enabled MPLS LDP for VLANIF 4001: enabled MPLS Layer 2 VPN: enabled Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 452 LDP remote peer and then enter the remote peer mode. Then, run the remote-ipip-addr command to specify the ID of the remote LSR. l For detailed configurations, see Configuring the LDP LSP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 453 (Optional) Configure the jitter buffer size. The jitter buffer can effectively prevent jitter and delay. Only PW parameters of the TDM type support the jitter buffer configuration. By default, the jitter buffer size is 2000 μs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 454 Set TDM connection ID to 2, type to PWE3, and ID of the E1 port of the H802EDTB board to 0/4/5. huawei(config)#tdm-connect connectid 2 tdm pwe3-uplink 0/4 e1 0/4/5 Step 7 Bind the TDM connection to the PW to create the PW service of the TDM type.

  • Page 455: Configuration Example Of Tdm Shdsl For Transparently Transmitting The Narrowband Data Private Line Service

    The user-side configuration data is transparently transmitted on the MA5600T/MA5603T/ MA5608T. The following figure shows an example network of TDM SHDSL for transparently transmitting the narrowband data private line service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 456 The H802EDTB board must be in position and must work in the normal state. An SHDSL modem must be correctly connected and the SHDSL port(s) must be activated. For details, see Configuring an SHDSL Port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 457 If E1 port 0 is used for transparently transmitting the narrowband data private line service: interface edt 0/3 board workmode voice runmode service e1port runmode 0 transparent quit save Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 458: Configuration Example Of The Private Line Service Leasing E1 Timeslots

    E1 and SHDSL ports, the EDTB board multiplexes timeslot channels of different lines to the same E1 upstream port, implementing convergence of multiple Nx64 kbit/s channels to the E1 port and saving E1 resources. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 459 Working sub-mode: service mode Clock source: E1 line clock E1 port Upstream port ID: 0/3/0 Line coding mode: HDB3 (default) Port impedance: 75 ohms (default) Port signaling mode: CCS Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 460 0 Step 2 Configure the attributes of the SHDSL port. Set the signaling mode of the SHDSL port to unframe. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 461 > G.SHDSL data frame type(1--E1;2--V35)[1]: > G.SHDSL data clock align(1--synchronization 2--asynchronism) [1]: > Clock mode(1--freeRun 2--system)[1]: > Do you config the target SNR margin?(y/n) [n]:n Add profile 2 successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 462 In CCS mode, timeslot 0 of the E1 port is used to send the frame locating information but is not used to send data. Therefore, it cannot be used for internal SPC. huawei(config)#spc huawei(config-spc)#anspc add start 0/3/16/0 end 0/3/0/1 apptype normal channelnum huawei(config-spc)#anspc add start 0/3/17/0 end 0/3/0/9 apptype normal channelnum Step 5 Query the status of the internal SPCs.
  • Page 463 0/3 e1port signal 0 ccs quit anspc add start 0/3/16/0 end 0/3/0/1 apptype normal channelnum 8 anspc add start 0/3/17/0 end 0/3/0/9 apptype normal channelnum 4 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 464: Configuration Example Of Mstp Subtending Network

    This topic describes how to configure MA5600T/MA5603T/MA5608T-4. 5.7 Configuring MA5600T/MA5603T/MA5608T-5 This topic describes how to configure MA5600T/MA5603T/MA5608T-5. 5.8 Verification All services configured on all DSLAMs run in the normal state. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 465: Mstp Networking

    MA5600T/MA5603T/MA5608T-3, through whose GE port, is subtended with MA5600T/ MA5603T/MA5608T-4. MA5600T/MA5603T/MA5608T-1 works with MA5600T/MA5603T/MA5608T-5 to provide the QinQ service through the IP network. Figure 5-1 shows an example MSTP network of the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 466: Mstp Dataplan

    This topic provides the data plan for the example RSTPMSTP network. Table 5-1 provides the service and the data plan for the example network of the MA5600T/ MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 467 Gateway: Gateway: 10.10.1.1/24 10.10.1.1/24 10.10.1.1/24 10.10.1.1/24 10.10.1.1/24 GE port Upstream: Upstream: Upstream: Upstream: Upstream: of the 0/20/0 0/19/0-0/19/1 0/19/0- 0/19/0 0/19/0 0/19/1 RSTP: board 0/19/0-0/19/1 RSTP: 0/20/0 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 468 POTS: 0/3 QinQ: 0/5/31 0/2/0-10 (maps VLAN 60, ISP1) Multicast: Multicast: 0/2/2, 0/2/3 0/2/2, 0/2/3 0/2/11-20 (maps VLAN 61, ISP2) 0/2/21-30 (maps VLAN 62, ISP3) Triple Play: 0/2/31 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 469 The upper layer device classifies the downstream traffic. Different service carries different 802.1p labels. The VLAN mapping to the DSLAM is configured in the upper-layer IP network. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 470: Configuring Ma5600T/Ma5603T/Ma5608T-1

    1 huawei(config)#ip route-static 3.3.4.0 255.255.255.0 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 471 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 5 Configuration Example of MSTP Subtending Network huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.4 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.5 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 472 MA5600T/MA5603T/MA5608T-1 is subtended with MA5600T/MA5603T/MA5608T-2, MA5600T/MA5603T/MA5608T-3 and MA5600T/MA5603T/MA5608T-4. Therefore, subtending should be configured. huawei(config)#vlan 60 to 62 standard huawei(config)#port vlan 60 to 62 0/19 0-2 huawei(config)#vlan 101 to 102 standard huawei(config)#port vlan 101 to 102 0/19 0-2 Step 7 Configure MSTP.
  • Page 473 3-singleSymbol twoSymbols > 5-threeSymbols 6-fourSymbols 7-fiveSymbols sixSymbols > 9-sevenSymbols 10-eightSymbols 11-nineSymbols tenSymbols > 13-elevenSymbols 14-twelveSymbols 15-thirteenSymbols 16- fourteenSymbols > 17-fifteenSymbols 18- sixteenSymbols > Please select (1~18) [2]: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 474 Will you set channel configuration parameters? (y/n) [n]:y > Please set the channel number (1~2) [1]: > Channel1 configuration parameters: > Please set the channel-profile index (1~128) [1]: Add template 10 successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 475 All ports in slot 0/3 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port from-vlan 1000 port 0/2 0-31 vpi 0 vci 35 rx- cttr 6 tx-cttr 6 Step 9 Configure the SHDSL service.
  • Page 476 Ports 0-14 in slot 0/5 provide the SHDSL service. To activate the ports in batches, run the multi-service-port command. huawei(config)#multi-service-port from-vlan 1300 port 0/5 0-15 vpi 0 vci 35 rx- cttr 6 tx-cttr 6 Step 10 Configure the GPON service.
  • Page 477 1 0 1 profile-id 10 Divide the ONT port VLAN. huawei(config-if-gpon-0/18)#ont port vlan 1 0 eth 10 0 huawei(config-if-gpon-0/18)#ont port native-vlan 1 0 eth 1 vlan 1510 Configure the GEM port. huawei(config-if-gpon-0/18)#gemport add 1 gemportid 150 eth 10. Bind the GEM port to an ONT T-CONT.
  • Page 478 PVC-priority policy. huawei(config)#traffic table ip index 7 cir off priority 0 priority-policy local-Setting huawei(config)#service-port vlan 50 shdsl mode atm 0/5/15 vpi 0 vci 36 rx-cttr 7 tx-cttr 7 Step 13 Configure the multicast service. After the configuration, the following results should be achieved: l Users of port 0/2/2 must be authenticated, and have rights to watch two programs and to preview one program.
  • Page 479 8 cir off priority 5 priority-policy local-Setting l Add ADSL2+ port 2 and 3 to VLAN 100. huawei(config)#service-port 100 vlan 100 adsl 0/2/2 vpi 0 vci 35 rx-cttr 8 tx-cttr 8 huawei(config)#service-port 101 vlan 100 adsl 0/2/3 vpi 0 vci 35 rx-cttr 8 tx-cttr 8 Configure the multicast service.

  • Page 480: Configuring Ma5600T/Ma5603T/Ma5608T-2

    Specify a subtending port. huawei(config-mvlan100)#quit huawei(config)#btv huawei(config-btv)#igmp cascade-port 0/19/0 huawei(config-btv)#igmp cascade-port 0/19/1 l Modify the subtending port. huawei(config-btv)#igmp cascade-port modify 0/19/0 static enable huawei(config-btv)#igmp cascade-port modify 0/19/1 static enable Step 15 Save the data. huawei(config-btv)#quit huawei(config)#save ----End 5.4 Configuring MA5600T/MA5603T/MA5608T-2 This topic describes how to configure MA5600T/MA5603T/MA5608T-2.
  • Page 481 1 huawei(config)#ip route-static 3.3.4.0 255.255.255.0 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 482 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 5 Configuration Example of MSTP Subtending Network huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3 trap-paramsname 123 Set the trap source address. huawei(config)#snmp-agent trap source vlanif 10 Step 3 Configure the time server.
  • Page 483 Will you set network timing reference? (y/n) [n]: Add profile 10 successfully Configure the ADSL2+ channel profile. You can configure the ADSL2+ channel profile based on your requirements. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 484 Will you set rate thresholds? (y/n) [n]: > Will you set retransmission function (y/n) [n]: > Will you set erasure decoding? (y/n) [n]: Add profile 10 successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 485 Add the service port. All ports in slot 0/3 provide the ADSL2+ services. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 2020 port 0/2 0-31 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 10 Configure the SHDSL service.
  • Page 486 Ports 0-15 of the SHDSL board in 0/5 provide the SHDSL services. l To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3020 port 0/5 0-15 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 11 Configure the POTS service.
  • Page 487 Add the upstream port. huawei(config)#port vlan 60 to 62 0/19 0-1 Add the service port. huawei(config)#multi-service-port vlan 60 port 0/2 0-10 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 huawei(config)#multi-service-port vlan 61 port 0/2 11-20 vpi 0 vci 35 rx-cttr...
  • Page 488 Configure the service port. huawei(config)#service-port vlan 100 adsl 0/2/31 vpi 0 vci 35 rx-cttr 8 tx-cttr huawei(config)#service-port vlan 101 adsl 0/2/31 vpi 0 vci 36 rx-cttr 6 tx-cttr huawei(config)#service-port vlan 102 adsl 0/2/31 vpi 0 vci 37 rx-cttr 7 tx-cttr Configure the DHCP relay mode for the video service.
  • Page 489 Configure the multicast user. huawei(config-btv)#igmp user add port 0/2/15 adsl 0 35 no-auth huawei(config-btv)#igmp user add port 0/2/16 adsl 0 35 auth huawei(config-btv)#igmp user bind-profile port 0/2/16 profile-name profile0 huawei(config-btv)#quit huawei(config)#multicast-vlan 100...

  • Page 490: Configuring Ma5600T/Ma5603T/Ma5608T-3

    1 huawei(config)#ip route-static 3.3.4.0 255.255.255.0 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 491 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 5 Configuration Example of MSTP Subtending Network huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.4 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 4.4.4.5 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 492 MA5600T/MA5603T/MA5608T-1 is subtended with MA5600T/MA5603T/MA5608T-2, MA5600T/MA5603T/MA5608T-3 and MA5600T/MA5603T/MA5608T-4. Therefore, the subtending should be configured. huawei(config)#vlan 60 to 62 standard huawei(config)#port vlan 60 to 62 0/19 0-1 huawei(config)#vlan 101 to 102 standard huawei(config)#port vlan 101 to 102 0/19 0-1 huawei(config)#vlan 100 standard huawei(config)#port vlan 100 0/19 0-1 Step 7 Enable MSTP.
  • Page 493 3-singleSymbol twoSymbols > 5-threeSymbols 6-fourSymbols 7-fiveSymbols sixSymbols > 9-sevenSymbols 10-eightSymbols 11-nineSymbols tenSymbols > 13-elevenSymbols 14-twelveSymbols 15-thirteenSymbols 16- fourteenSymbols > 17-fifteenSymbols 18- sixteenSymbols > Please select (1~18) [2]: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 494 (template 1) is used. Configure the ADSL2+ traffic profile. You can configure the ADSL2+ traffic profile by running the traffic table ip command based on your requirements. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 495 Add the service port. All ports in slot 0/3 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port from-vlan 1000 port 0/3 0-31 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 9 Configure the SHDSL service.
  • Page 496 Add the service port. Ports 0-15 in slots 0/5 provide the SHDSL service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3030 port 0/5 0-15 vpi 0 vci 35 user- encap pppoe rx-cttr 6 tx-cttr 6 Step 10 Configure the GPON service.
  • Page 497 1 0 1 profile-id 10 Divide the ONT port VLAN. huawei(config-if-gpon-0/18)#ont port vlan 1 0 eth 10 0 huawei(config-if-gpon-0/18)#ont port native-vlan 1 0 eth 0 vlan 1530 Configure the GEM port. huawei(config-if-gpon-0/18)#gemport add 1 gemportid 150 eth 10. Bind the GEM port to an ONT T-CONT.

  • Page 498: Configuring Ma5600T/Ma5603T/Ma5608T-4

    1 huawei(config)#ip route-static 3.3.4.0 255.255.255.0 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 499 SNMP V2C. huawei(config)#snmp-agent sys-info version v2c Enable trap sending. huawei(config)#snmp-agent trap enable standard Set the trap destination address. huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2 trap-paramsname abc huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3 trap-paramsname 123 Set the trap source address.
  • Page 500 You can configure the ADSL2+ channel profile based on your requirements. huawei(config)#adsl channel-profile add 10 Start adding profile Press 'Q' to quit the current configuration and new configuration will Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 501 The configured ADSL2+ line profile and the ADSL2+ channel profile are bound together in the ADSL2+ line template and the index of the ADSL2+ line template is 10. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 502 Add the service port. All ports in slot 0/2 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 2040 port 0/2 0-31 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 8 Configure the SHDSL service.
  • Page 503 Add the service port. Ports 0-15 in slot 0/5 provide the SHDSL service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3040 port 0/5 0-15 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 9 Configure the GPON service.
  • Page 504 1 0 1 profile-id 10 Divide the ONT port VLAN. huawei(config-if-gpon-0/18)#ont port vlan 1 0 eth 10 0 huawei(config-if-gpon-0/18)#ont port native-vlan 1 0 eth 0 vlan 1530 Configure the GEM port. huawei(config-if-gpon-0/18)#gemport add 1 gemportid 150 eth 10. Bind the GEM port to an ONT T-CONT.
  • Page 505 8 cir off priority 5 priority-policy local-Setting l Add ADSL2+ ports 2 and port 3 to VLAN 100. huawei(config)#service-port vlan 100 adsl 0/2/2 vpi 0 vci 35 rx-cttr 8 tx-cttr 8 huawei(config)#service-port vlan 100 adsl 0/2/3 vpi 0 vci 35 rx-cttr 8...

  • Page 506: Configuring Ma5600T/Ma5603T/Ma5608T-5

    In this example, configure the preview authority profile with the preview duration for the program to 150s, the number of preview attempts to 6 each day, and the preview interval to 60s. huawei(config-btv)#igmp preview-profile add index 1 duration 150 times 6 interval 60 huawei(config-btv)#igmp preview auto-reset-time 00:00:00 huawei(config-btv)#quit l Configure the program library.
  • Page 507 1 huawei(config)#ip route-static 3.3.4.3 255.255.255.255 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 508 NMS version is set as SNMP V2C. huawei(config)#snmp-agent sys-info version v2c Enable the trap sending. huawei(config)#snmp-agent trap enable standard Set the trap destination address. huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2 trap-paramsname abc huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3 trap-paramsname 123 Set the trap source address.
  • Page 509 Press 'Q' to quit the current configuration and new configuration will neglected > Do you want to name the profile (y/n) [n]: > Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 510 Bind the preceding configured line profile and the channel profile together in the line template with the index of 10. huawei(config)#vdsl line-template add 10 Start adding template Press 'Q' to quit the current configuration and new configuration will be Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 511 All ports in slot 0/2 provide the VDSL2 Internet access service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 1800 port 0/2 0-23 vpi 0 vci 35 user-encap pppoe rx-cttr 6 tx-cttr 6 Step 7 Configure the QinQ private line service.

  • Page 512: Verification

    The QinQ VLAN supports the PVC-priority scheduling policy only. In this case, select the profile that supports PVC-priority policy. huawei(config)#traffic table ip index 7 cir off priority 0 priority-policy local-Setting huawei(config)#service-port vlan 50 shdsl mode atm 0/5/15 vpi 0 vci 35 rx-cttr 7 tx-cttr 7 Step 8 Save the data. huawei(config)#save ----End 5.8 Verification...

  • Page 513: Configuration Example Of Vpls

    Virtual switch instance. This concept corresponds to virtual local area network (VLAN) of Ethernet switch. Each VSI provides independent VPLS service. VSI supports the Ethernet bridge function and can terminate PW. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 514 6.3 Configuration Example of the VPLS Enterprise Private Line Service This topic describes how to configure the enterprise private line service when the VPLS networking is used at the access and aggregation layers. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 515: Configuration Example Of The Vpls Internet Access Service

    Figure 6-1 Networking for the VPLS Internet access service for individual users Prerequisite Traffic streams have been configured on the MA5600T/MA5603T/MA5608T for the Internet access service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 516 PWs are type: ethernet transmitted to BRAS devices consistent with those on the tagged over two trails. MA5600T/MA5603T/ l The control MA5608T. word is enabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 517 4001 Set the IP address of VLAN interface 4001 to 10.50.50.50/24 and enable MPLS LDP for the VLAN interface. huawei(config)#interface vlanif 4001 huawei(config-if-vlanif4001)#ip address 10.50.50.50 24 huawei(config-if-vlanif4001)#mpls Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 518 1 huawei(config-pw-para-index-1)#peer-address 3.3.3.3 huawei(config-pw-para-index-1)#pw-type ethernet tagged huawei(config-pw-para-index-1)#control-word enable huawei(config-pw-para-index-1)#dyn-receive-label 10240 huawei(config-pw-para-index-1)#quit huawei(config)#pw-para pwindex 2 huawei(config-pw-para-index-2)#service-type vpls huawei(config-pw-para-index-2)#pwid 2 huawei(config-pw-para-index-2)#peer-address 4.4.4.4 huawei(config-pw-para-index-2)#pw-type ethernet tagged huawei(config-pw-para-index-2)#control-word enable Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 519: Configuration Example Of The Vpls Multicast Service

    VSI (VPLS instance). The multicast VLAN is bound to VSI for carrying multicast services over the VPLS network, including upstream IGMP packets and downstream multicast traffic streams. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 520 VPLS multicast services and the default mode is used for the multicast upstream ports. Data Plan Table 6-3 provides the key data plan for the MA5600T/MA5603T/MA5608T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 521 VPLS domain, so that must bind the corresponding multicast service packets can l Multicast be broadcast in the VPLS service VLAN domain. 100 is bound to VSI. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 522 Step 4 Configure the remote LDP session. Configure the remote LDP sessions from the MA5600T/MA5603T/MA5608T to SPE1 (LSR ID: 1.1.1.1) and SPE2 (LSR ID: 2.2.2.2) respectively. Name the sessions to_spe1 and to_spe2 respectively. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 523 The same restrictions are set for binding multicast VLANs and VSI as those for binding unicast VLANs and VSI. That is, when the VPLS encapsulation type is raw, one VIS can Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 524: Configuration Example Of The Vpls Enterprise Private Line Service

    PEs (PE1-PE4) through VPLS PWs. For important branch offices, a PW protection group is configured to provide protection. PEs are connected to the OLT/MSAN using Spoke PW. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 525 The configurations are the same as those for common QinQ VLAN private line service, which are not described here. Data Plan Table 6-4 provides the key data plan for the OLT/MSAN (MA5600T/MA5603T/MA5608T). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 526 Ensure that the Layer 3 those on PE1-PE4 can ping interfaces and LSR IDs on each other. PE1-PE4 and those on the MA5600T/MA5603T/ MA5608T can ping each other. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 527 Configure the MPLS LSR-ID. Use the IP address of loopback interface 0 as the LSR ID. huawei(config)#mpls lsr-id 10.10.10.10 Enable MPLS globally. Trigger LDP by the IP address of the host to set up an LSP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 528 2.2.2.2 huawei(config-mpls-ldp-remote-to_pe2)#remote-ip auto-dod-request huawei(config-mpls-ldp-remote-to_pe2)#quit huawei(config)#mpls ldp remote-peer to_pe3 huawei(config-mpls-ldp-remote-to_pe3)#remote-ip 3.3.3.3 huawei(config-mpls-ldp-remote-to_pe3)#remote-ip auto-dod-request huawei(config-mpls-ldp-remote-to_pe3)#quit huawei(config)#mpls ldp remote-peer to_pe4 huawei(config-mpls-ldp-remote-to_pe4)#remote-ip 4.4.4.4 huawei(config-mpls-ldp-remote-to_pe4)#remote-ip auto-dod-request huawei(config-mpls-ldp-remote-to_pe4)#quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 529 PE, and split horizon is not performed between PWs. huawei(config)#vsi enterprise_vpn huawei(config-vsi-enterprise_vpn)#vsi-pw-binding pwindex 1 spoke huawei(config-vsi-enterprise_vpn)#vsi-pw-binding pwindex 2 huawei(config-vsi-enterprise_vpn)#vsi-pw-binding pwindex 3 huawei(config-vsi-enterprise_vpn)#vsi-pw-binding pwindex 4 spoke Step 8 Configure VPLS PW protection. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 530 When a PE which branch C is connected to is faulty, services can be automatically switched to another PE and therefore services are not affected. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 531: Example: Subtending Networking

    This topic describes how to configure MA5600T-3. 7.6 Configuring MA5600T-4 This topic describes how to configure MA5600T-4. 7.7 Verification All services configured on all DSLAMs run in the normal state. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 532: Subtended Network

    MA5600T-1 is subtended with MA5600T-2 through the GE port on the GIU board. MA5600T-2 is subtended with MA5600T-3 through the GE port on the GIU board. Figure 7-1 shows an example subtended network of the MA5600T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 533: Data Plan For Subtended Network

    7 Example: Subtending Networking Figure 7-1 Example subtended network of the MA5600T 7.2 Data Plan for Subtended Network This topic describes the data plan for the example subtended network. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 534 255.255.255.0 address Gateway: Gateway: Gateway: Gateway: 10.10.1.1/24 10.10.1.1/24 10.10.1.1/24 10.10.1.1/24 GE port Upstream: 0/19/0 Upstream: 0/19/0 Upstream: 0/19/0 Upstream: 0/19/0 of the Subtending: Subtending: 0/19/1 0/19/1 board Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 535 2944, port number of the active MGC is 2944, and transmission mode is UDP. NMS host 2.2.2.2 and 2.2.2.3 Log host 3.3.3.3 and 3.3.4.3 Time 4.4.4.4 and 4.4.4.5 server Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 536: Configuring Ma5600T-1

    Add the upstream port. huawei(config)#port vlan 10 0/19 0-1 It will take several minutes, and console may be timeout, please use command idle-timeout to set time Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 537 1 huawei(config)#ip route-static 3.3.4.3 255.255.255.255 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 538 MA5600T-1 is subtended with MA5600T-2 andMA5600T-3. Therefore, the subtending should be configured. huawei(config)#vlan 60 to 62 standard huawei(config)#port vlan 60 to 62 0/19 0-1 It will take several minutes, and console may be timeout, please use command idle-timeout to set time limit...
  • Page 539 Press 'Q' to quit the current configuration and new configuration will neglected > Do you want to name the template (y/n) [n]: > Please set the line-profile index (1~128) [1]: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 540 Add the service port. All ports in slot 0/3 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port from-vlan 1000 port 0/2 0-31 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 8 Configure the SHDSL service.
  • Page 541 Ports 0-15 in slot 0/5 provide the SHDSL service. l To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port from-vlan 1300 port 0/5 0-14 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 Step 9 Configure the GPON service.
  • Page 542 In this example, the default alarm threshold profile is used. You do not need to configure Configure the GPON traffic profile. huawei(config)#traffic table ip index 8 cir 10240 priority 0 priority-policy tag-In-Package Add an ONT.
  • Page 543 PVC-priority policy. huawei(config)#traffic table ip index 7 cir off priority 0 priority-policy local-Setting huawei(config)#service-port vlan 50 shdsl 0/5/15 vpi 0 vci 35 rx-cttr 7 tx-cttr 7 Step 12 Configure the multicast service. After the configuration, the following results should be achieved:...
  • Page 544 8 cir off priority 5 priority-policy local-Setting l Add ADSL2+ ports 0/0/2 and 0/0/3 to VLAN 100. huawei(config)#service-port vlan 100 adsl 0/2/2 vpi 0 vci 35 rx-cttr 8 tx- cttr 8 huawei(config)#service-port vlan 100 adsl 0/2/3 vpi 0 vci 35 rx-cttr 8 tx- cttr 8 Configure the multicast service.

  • Page 545: Configuring Ma5600T-2

    Configure the multicast user. huawei(config-btv)#igmp user add port 0/2/3 adsl 0 35 no-auth huawei(config-btv)#igmp user add port 0/2/2 adsl 0 35 auth huawei(config-btv)#igmp user bind-profile port 0/2/2 profile-name profile0 huawei(config-btv)#quit huawei(config)#multicast-vlan 100...
  • Page 546 1 huawei(config)#ip route-static 3.3.4.3 255.255.255.255 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 547 SNMP version is set as SNMP V2C. huawei(config)#snmp-agent sys-info version v2c Enable the trap sending. huawei(config)#snmp-agent trap enable standard Set trap destination address. huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2 trap-paramsname abc huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3 trap-paramsname 123 Set the trap source address.
  • Page 548 Minimum reserved transmit rate upstream (32~6000 Kbps) [32]: > Maximum transmit rate upstream (32~6000 Kbps) [1024]: > Will you set rate thresholds? (y/n) [n]: Add profile 10 successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 549 Add the service port. All ports in slot 0/2 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 2020 port 0/2 0-31 vpi 0 vci 35 user- encap pppo rx-cttr 6 tx-cttr 6 Step 8 Configure the SHDSL service.
  • Page 550 Add the service port. l Ports 0-15 of in slot 0/5 provide the SHDSL service. l To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3020 port 0/5 0-15 vpi 0 vci 35 user- encap pppoe rx-cttr 6 tx-cttr 6 Step 9 Configure the POTS service.
  • Page 551 Add the upstream port. huawei(config)#port vlan 60 to 62 0/19 0 Add the service port. huawei(config)#multi-service-port vlan 60 adsl 0/2 0-10 vpi 0 vci 35 rx-cttr 6 tx-cttr 6 huawei(config)#multi-service-port vlan 61 adsl 0/2 11-20 vpi 0 vci 35 rx-cttr 6 tx-cttr 6...
  • Page 552 : 67536 bytes Referenced Status : not used ------------------------------------------------ huawei(config)#traffic table ip index 8 cir off priority 5 priority-policy tag- In-Package Create traffic descriptor record successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 553 : not used ------------------------------------------------ Configure the service port. huawei(config)#service-port vlan 100 adsl 0/2/31 vpi 0 vci 35 rx-cttr 8 tx-cttr 8 huawei(config)#service-port vlan 101 adsl 0/2/31 vpi 0 vci 36 rx-cttr 6 tx-cttr 6 huawei(config)#service-port vlan 102 adsl 0/2/31 vpi 0 vci 37 rx-cttr 7 tx-cttr 7 Configure DHCP relay mode for video service.
  • Page 554 Are you sure to change the uplink port mode?(y/n)[n]:y huawei(config-btv)#quit huawei(config)#multicast-vlan 100 huawei(config-mvlan100)#igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10 huawei(config-mvlan100)#igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.10 huawei(config-mvlan100)#igmp program add name program3 ip 224.1.1.3 sourceip 10.10.10.10...

  • Page 555: Configuring Ma5600T-3

    1 huawei(config)#ip route-static 3.3.4.3 255.255.255.255 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 556 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 7 Example: Subtending Networking huawei(config-acl-adv-3050)#rule permit ip source 3.3.3.3 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 3.3.4.3 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#quit huawei(config)#packet-filter inbound ip-group 3050 port 0/19/0 huawei(config)#packet-filter inbound ip-group 3050 port 0/19/1 Configure SNMP.
  • Page 557 Minimum reserved transmit rate upstream (32~6000 Kbps) [32]: > Maximum transmit rate upstream (32~6000 Kbps) [1024]: > Will you set rate thresholds? (y/n) [n]: Add profile 10 successfully Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 558 Add the service port. All ports of in slot 0/2 provide the ADSL2+ service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3030 port 0/3 0-31 vpi 0 vci 35 user- encap pppoe rx-cttr 6 tx-cttr 6 Step 7 Configure the SHDSL service.
  • Page 559 Add the service port. l Ports 0-15 of SHDSL board 0/5 provide the SHDSL service. l To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 3030 port 0/5 0-15 vpi 0 vci 35 user- encap pppoe rx-cttr 6 tx-cttr 6 Step 8 Configure the GPON service.
  • Page 560 7 Example: Subtending Networking l In this example, the default alarm threshold profile is used. You do not need to configure Configure the GPON traffic profile. huawei(config)#traffic table ip index 8 cir 10240 priority 0 priority-policy tag-In-Package Add an ONT.
  • Page 561 Add ADSL2+ port 2 and 3 to VLAN 100. huawei(config)#service-port vlan 100 adsl 0/2/2 vpi 0 vci 35 rx-cttr 8 tx- cttr 8 huawei(config)#service-port vlan 100 adsl 0/2/3 vpi 0 vci 35 rx-cttr 8 tx- cttr 8...

  • Page 562: Configuring Ma5600T-4

    In this example, set the preview duration for program 1 to 150s, the number of preview attempts to 6 each day, and the preview interval to 60s. huawei(config-btv)#igmp preview-profile add index 1 duration 150 times 6 interval 60 huawei(config-btv)#igmp preview auto-reset-time 00:00:00 huawei(config-btv)#quit l Configure the program library.
  • Page 563 1 huawei(config)#ip route-static 3.3.4.3 255.255.255.255 10.10.1.1 preference 1 Add the ACL rule. huawei(config)#acl 3050 huawei(config-acl-adv-3050)#rule permit ip source any destination any huawei(config-acl-adv-3050)#rule deny ip source any destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.2 0.0.0.0 destination 10.10.1.2 0.0.0.0 huawei(config-acl-adv-3050)#rule permit ip source 2.2.2.3 0.0.0.0 destination 10.10.1.2 0.0.0.0...
  • Page 564 SNMP version is set as SNMP V2C. huawei(config)#snmp-agent sys-info version v2c Enable the trap sending. huawei(config)#snmp-agent trap enable standard Set trap destination address. huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2 trap-paramsname abc huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3 trap-paramsname 123 Set the trap source address.
  • Page 565 Please set the line-profile index (1~128) [1]:10 > Will you set channel configuration parameters? (y/n) [n]:y > Please set the channel number (1~2) [1]: > Channel1 configuration parameters: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 566 Add the service port. All ports in slot 0/2 provide the VDSL2 Internet access service. To add service ports in batches, run the multi-service-port command. huawei(config)#multi-service-port vlan 1800 port 0/2 0-23 vpi 0 vci 35 user- encap pppoe rx-cttr 6 tx-cttr 6 Step 7 Configure the QinQ private line service.

  • Page 567: Verification

    7 Example: Subtending Networking The QinQ VLAN supports the PVC-priority scheduling policy only. In this case, select the profile that supports PVC-priority policy. huawei(config)#service-port vlan 50 shdsl 0/5/15 vpi 0 vci 35 rx-cttr 7 tx-cttr 7 Step 8 Save the data.

  • Page 568: Fttx Configuration Summary

    QoS, and specific service in various sub-solutions. In this case, you can plan and deploy services efficiently. Takes the FTTB/C sub-solution as an example, the principle of data plan is shown in Figure 8-1. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 569 One-button Script Tool Through a simple-to-use interface, you can instantly transform any configuration page into command scripts, which greatly reduces the probability of errors compared to manually. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 570 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 8 FTTx Configuration Summary Click to experience: Script Conversion Tool. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 571: Ftth Configuration

    (OLT) and optical network terminals (ONTs). 9.5 Reference of GPON ONT Capability Sets This topic provides common GPON ONT capability sets of Huawei, serving as a reference for parameter configuration when an ONT is added offline.

  • Page 572: Ftth Service Overview

    FTTH networking using PON and P2P upstream transmission, respectively. FTTH Networking Using PON Upstream Transmission FTTH Networking Using P2P Upstream Transmission Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 573 ONTs connect to home users. In P2P networking, an OLT connects to ONTs and the ONTs connect to home users. The OLT provides voice, Internet access, and IPTV services for home users. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 574: Networking Scenarios And Hardware Configurations (Gpon)

    9.3 Networking Scenarios and Hardware Configurations (GPON) This section describes fiber to the home (FTTH) networking scenarios and hardware configurations of an optical line terminal (OLT) and optical network terminals (ONTs). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 575 The ONT with a built-in voice module encapsulates voice service packets, and the OLT transmits them to the upstream next generation network (NGN) or IP multimedia subsystem (IMS). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 576: Networking Scenarios And Hardware Configurations (P2P)

    9.4 Networking Scenarios and Hardware Configurations (P2P) This section describes fiber to the home (FTTH) networking scenarios and hardware configurations of an optical line terminal (OLT) and optical network terminals (ONTs). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 577: Reference Of Gpon Ont Capability Sets

    Internet access, and IPTV FTTH services for users. Service 9.5 Reference of GPON ONT Capability Sets This topic provides common GPON ONT capability sets of Huawei, serving as a reference for parameter configuration when an ONT is added offline. Prod User- Numb...
  • Page 578 Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI HG80 Support VLAN/ PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 579 Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI HG80 Support VLAN/ PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 580 +VLA N/Port +PRI/ Port +VLA N+PRI HG81 1POTS Support VLAN/ +1GE PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 581 +VLA N/Port +PRI/ Port +VLA N+PRI HG82 2POTS Support VLAN/ +4GE PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 582 +VLA N/Port +PRI/ Port +VLA N+PRI HG82 2POTS Support VLAN/ +4GE PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 583 N/Port +PRI/ Port +VLA N+PRI Gatew HG82 2POTS Support VLAN/ +4FE PRI/ Gempor VLAN t CAR/ +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 584 Support VLAN/ +4GE PRI/ Gempor CONT +USB VLAN t CAR/ 0: 3 +WiFi +PRI/ Flow IPToS/ CONT Port/ 1-7: 4 Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 585 +PRI/ Port +VLA N+PRI HG82 2POTS Support VLAN/ +4GE PRI/ Gempor +USB VLAN t CAR/ +WiFi +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 586 +PRI/ Port +VLA N+PRI HG82 2POTS Support VLAN/ +4GE PRI/ Gempor +USB VLAN t CAR/ +WiFi +PRI/ Flow IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 587 +PRI/ Port +VLA N+PRI HG82 2POTS Support VLAN/ +4GE PRI/ Gempor +USB VLAN t CAR/ +PRI/ Flow +WiFi IPToS/ Port/ Port +VLA N/Port +PRI/ Port +VLA N+PRI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 588: Principle Of Ftth Data Plan

    Data Plan Principles for IP Addresses Terminal Service Recommended Solution Type Bridging Internet A PC obtains an IP address through PPPoE dialup. The ONT +Voice ONT access transparently transmits the packets. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 589: Principle Of Qos Planning

    The QoS planning is an E2E planning, and it can be divided into following policies: traffic classification, marking, and scheduling policy; and traffic monitoring and DBA policy. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 590 Rate limit on No rate limit Configure rate No rate limit No rate limit limit by a traffic downstream profile as required. [Remark 2] Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 591 (in the case of multiple STBs). The upstream bandwidth is mainly used for transmitting IGMP packets, which requires little bandwidth. Therefore, the bandwidth occupied by IGMP packets can be neglected. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 592: Principle Of Internet Access Service Data Plan

    C-VLAN tag to packets. All ONTs are in the same C-VLAN. OLT: The OLT performs VLAN translation: C<->S+C'. The C'-VLAN of every ONT differs from each other. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 593 The 802.1q in 802.1q (QinQ) VLAN is used in the enterprise private line scenario, such as (TLS). The device transparently transmits packets. It is not recommended that you use QinQ VLANs as S-VLANs for the triple play services of residential users. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 594: Principle Of Voice Service Data Plan

    OLT have the same voice service S-VLAN; ONTs connected to different OLTs may have different voice service S-VLANs. OLT: transparently transmits the VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 595 C-VLAN: VLAN added based on the ONT/ONU port. For details, see the description of the Double-tagged VLAN S+C. Double-tagged VLAN S+C: C indicates the inner VLAN (C-VLAN) and S indicates the outer VLAN (S-VLAN). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 596 IP address and port ID of the standby MGC need to be Port ID of active MGC (H248)/ configured. port ID of active IMS device (SIP) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 597 The user type includes the following: l DEL: direct exchange lines (default) l ECPBX: earth calling PBX l LCPBX: loop calling PBX l PayPhone: pay phone Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 598: Principle Of Iptv Service Data Plan

    ONTs replicate multicast packets based on user +Voice service tagged ports and multicast VLANs (M-VLANs) are VLAN removed downstream. The OLT replicates multicast packets based on PON ports with M-VLAN unchanged. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 599 VLAN Untagged VLANs are translated to C-VLANs. The OLT implements VLAN translation: C -> Note: UserVLAN: VLAN carried by upstream packets of user-side devices, U for short. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 600: Principle Of Security Data Plan

    After the anti-DoS-attack function is function for OLT. enabled, control packets are monitored and those exceeding the number threshold are discarded. Use this solution for new site deployment. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 601 After anti-IP spoofing is enabled, the function for OLT. system can prevent users from forging IP addresses to perform malicious attacks. Use this solution for new site deployment. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 602: Gpon Access: Configuring Ftth Service

    VoD service in GPON access mode in FTTH network scenario. Context There are two xPON configuration modes: distributed mode (also called discrete mode) and profile mode. The difference between the two modes lies in command lines. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 603: Bridging+Voice Ont Network Scenario

    Service faults are easy to locate and services are easy to maintain. Application Scenario As shown in Figure 9-1, the ONT integrating an integrated access device (IAD) provides Internet, VoIP, and IPTV services to users. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 604: Configuration Process

    Figure 9-1 Bridging+Voice ONT 9.7.1.2 Configuration Process Figure 9-2 shows the configuration roadmap in fiber to the home (FTTH) networking using a bridging+voice optical network terminal (ONT). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 605 Services can be configured for an ONT only line after the ONT is successfully added to an termina OLT. l (OLT) 9.7.1.4 Configuring the Internet None Access Service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 606 The global configuration of link aggregation Aggregation, Congestion and queue scheduling based on priorities Control, and Security Policies ensures service reliability. The global configuration of security policies ensures service security. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 607: Adding An Ont To An Olt

    GPON ONT profiles include the DBA profile, line profile, service profile, and alarm profile. l DBA profile: A DBA profile describes GPON traffic parameters. A T-CONT is bound to a DBA profile for dynamic bandwidth allocation, improving upstream bandwidth utilization. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 608 Create the same DBA profile for different types of services. Set the profile name to ftth_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to 20 Mbit/s. huawei(config)#dba-profile add profile-name ftth_dba type3 assure 8192 max 20480 NOTE The DBA implementation is based on an ONT.
  • Page 609 Add ONTs offline. If the password of an ONT is known, run the ont add command to add an ONT offline. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging omci ont-lineprofile-name ftth ont-srvprofile-name ftth huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging...

  • Page 610: Configuring The Internet Access Service

    ONTs by bulk confirming automatically discovered ONTs to make configuration easier and more efficient. To do so, the preceding command can be modified as follows: huawei(config-if-gpon-0/1)#ont confirm 0 all sn-auth omci ont-lineprofile-name ftth ont-srvprofile-name ftth l (Optional) Bind the alarm profile to the ONT.
  • Page 611 If the traffic profiles existing in the system do not meet the requirements, you need to run the traffic table ip command to add a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 612 Set the profile ID to ftth_hsi, the CIR to 4 Mbit/s, and the priority to 0. In addition, configure the scheduling mode so that packets are scheduled according to their priorities. huawei(config)#traffic table ip name ftth_hsi cir 4096 priority 0 priority- policy local-setting Configure the mapping between a GEM port and a VLAN.

  • Page 613: Configuring The H.248-Based Voice Service (On A Web Page Or The U2000)

    IP address of the MGC server: 200.200.200.200/24 Port ID of the MGC server: 2944 MG Domain: 0100000001 or 0100000002 Procedure Configure the OLT. Configure a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 614 Set the profile name to ftth_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 615 – Set VLAN ID to 300. (The VLAN ID of the ONT must be the same as the user-side VLAN ID configured on the OLT.) – Set 802.1p to 5. – Set IP Acquisition Mode to DHCP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 616 – Set Address of the Primary MGC to 200.200.200.200. – Set MID Format to Domain Name and MG Domain to 0100000001. – Set Signaling Port to 1_VOIP_R_VID_300. – Set Region to China. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 617 If Associated POTS Port is 1, port TEL1 on the ONT is bound. If Associated POTS Port is 2, port TEL2 on the ONT is bound. Click Apply. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 618 – VLAN ID: 300 (The VLAN ID of the ONT must be the same as the user-side VLAN ID configured on the OLT.) – Priority: 5 – Addressing Type: DHCP Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 619 WAN port named WAN-RTP on the ONT, and set this WAN port to a media WAN port. Specifically, choose Interface 1 > RTP and set Associate WAN Interface to WAN2. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 620 In the right pane, set User Enabled to Enable, and Interface ID to 2. NOTE If Interface ID is 1, port TEL1 on the ONT is bound. If Interface ID is 2, port TEL2 on the ONT is bound. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 621 WAN Connection > WAN Connection 1 > WAN IP Interface > WAN IP Interface 1 from the navigation tree, and set WAN Interface Name to ONT- VoIP, Service Type to VOIP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 622 Pay attention to the RTP TID configuration when the ONT is interconnected with a softswitch of other vendors. The terminal IDs A0 and A1 must be consistent with the corresponding configuration on the MGC. Do not configure Directory Number. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 623: Configuring The H.248-Based Voice Service (Through The Cli)

    The ONT software version of the H.248 voice service can be configured as V100R002C04 or later through the CLI. Data Plan Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 624 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 300, and use traffic profile ftth_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table name...
  • Page 625 For ONT 1 and ONT 2, configure the IP address obtaining mode to DHCP mode, set the management VLAN to VLAN 20, and use default values for other parameters. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20 huawei(config-if-gpon-0/1)#ont ipconfig 0 2 dhcp vlan 20 Step 8 Configure H.248 POTS users.
  • Page 626 For ONT 1 and ONT 2, create a POTS user, set the MG ID to 1 (identical to the MG ID of the H.248 interface), and set the physical terminal port ID to A0 and A1. huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 1 mgid 1 terminalid A0 huawei(config-if-gpon-0/1)#mgpstnuser add 0 2 1 mgid 1 terminalid A1 Run the display mgpstnuser attribute command to check whether the configuration of the POTS user is properly set.

  • Page 627: Configuring The Sip-Based Voice Service (On A Web Page Or The U2000)

    ONTs have the same C-VLAN. The ONT adds a C-VLAN tag to packets. l OLT: transparently transmits the VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 628 Set the profile name to ftth_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 629 – Set Service Type to VOIP. (For configuring the VoIP service, VoIP or a combination containing VoIP needs to be selected.) – Set WAN mode to Route WAN. – Select Enable VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 630 Choose Voice > VoIP Basic Configuration. In the Basic Interface Parameters(SIP) window, configure the parameters as follows: – Set Address of the Primary Proxy Server to 200.200.200.200. – Set Home Domain to huawei.com. – Set Region to China. – Set Signaling Port to 1_VOIP_R_VID_300. NOTE l The parameters of the SIP-based voice interface must be consistent with the corresponding configuration on the softswitch.
  • Page 631 – Set Registration User Name to 77730010. – Set Associated POTS Port to 1. – Set Authentication User Name to +8675577730010@huawei.com. – Set Password to iadtest1. Click New to add voice user 2, and set the parameters for voice user 2 as follows: –...
  • Page 632 On the General ONT VAS Profile tab page, right-click, and choose Add from the shortcut menu. In the dialog box that is displayed, set Name to ONT-VoIP. Configure the parameters of a voice WAN port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 633 In the navigation tree, choose General Para > Services > Voice Service > Voice Service 1 > Interface configuration > Interface 1 > SIP. Select SIP and enter (or select) a proper value. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 634 ONT is bound. Click Next. In the dialog box that is displayed, set vendor ID to HWTC, Terminal Type to General Type, and Version to V1R003C00-ZZ, click Add. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 635 Select an ONT from the list, right-click, and choose Bind General VAS Profile from the shortcut menu. In the dialog box that is displayed, select the created profile, and click OK to complete profile binding. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 636: Configuring The Sip-Based Voice Service (Through The Cli)

    SIP server. The connection between the OLT and the SIP server is set up. The OLT can ping the IP address of the SIP server successfully. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 637 Step 2 Configure the mapping relationship between a GEM port and a VLAN. The service flow of user VLAN 300 is mapped to GEM port 12 in the ONT line profile. huawei(config)#ont-lineprofile gpon profile-name ftth huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 300 Issue 01 (2014-04-30) Huawei Proprietary and Confidential...
  • Page 638 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 300, and use traffic profile ftth_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table name...
  • Page 639 POTS users named huawei1 and huawei2, set passwords to user1 and user2, set their phone numbers to 77730010 and 77730020 and use default values for other parameters. huawei(config-if-gpon-0/1)#sippstnuser add 0 1 1 mgid 1 username huawei1 telno 77730010 huawei(config-if-gpon-0/1)#sippstnuser add 0 2 1 mgid 1 username huawei2 telno...
  • Page 640 Access Module Commissioning and Configuration Guide 9 FTTH Configuration Run the display sippstnuser attribute command to check whether the configuration of the POTS user is properly set. huawei(config-if-gpon-0/1)#display sippstnuser attribute 0 1 1 ------------------------------------------------------------------------------ F/S/P : 0/1/0 ONT ID Port ID MG ID Telephone NO.

  • Page 641: Configuring The Btv Service

    9.7.1.3 Adding an ONT to an OLT. Data Plan Table 9-3 Data plan Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 13 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 642 Run the display traffic table ip command to query the existing traffic profiles in the system. If the existing traffic profiles in the system do not meet the requirements, run the traffic table ip command to add a traffic profile. huawei(config)#traffic table ip index 8 cir off priority 4 priority- policy local-setting Configure the mapping relationship between a GEM port and an Ethernet port on the ONT.
  • Page 643 Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to 1000, and use traffic profile 8. huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi- service user-vlan 1000 rx-cttr 8 tx-cttr 8...

  • Page 644: Configuring The Vod Service

    (Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic programs, perform this operation. For example, set the address range of dynamic programs to 224.1.1.1-224.1.1.100. huawei(config-mvlan1000)#igmp match group ip 224.1.1.1 to-ip 224.1.1.100 Set the IGMP mode. Select the IGMP proxy mode.
  • Page 645 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and a VLAN.

  • Page 646: Configuring Link Aggregation, Congestion Control, And Security Policies

    Set the service VLAN to 1100, GEM port ID to 13, and VLAN translation mode to transparent transmission, and use traffic profile 8. huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 rx-cttr 8 tx-cttr 8 tag-transform transparent huawei(config)#service-port 4 vlan 1100 gpon 0/1/0 ont 2 gemport 13 rx-cttr 8 tx-cttr 8 tag-transform transparent Save the data.
  • Page 647 11.2.2 Principle of QoS Data Plan. huawei(config)#queue-scheduler strict-priority huawei(config)#cos-queue-map cos0 0 cos4 4 cos5 5 cos6 6 Configure system security. – Enable deny of service (DoS) anti-attack on the OLT. Run the security anti-dos enable command to globally enable DoS anti-attack.
  • Page 648 DHCP Option 82 at the service port level. On the OLT, run the dhcp-option82 permit-forwarding service-port command with the enable parameter selected, to allow ONT DHCP packets to carry Option 82 information. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 649: Verifying Services

    Prerequisites ONTs and upper-layer devices have been connected properly. The BRAS and MGC/IMS have been configured. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 650 BRAS. Call ONT POTS ID: 1 The default values are used. You can run emulation the display pots emulational parameters configuration command to check the parameter values. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 651 { username<S><Length 1-64> }:test@huawei { user-password<K> }:user-password { password<S><Length 1-64> }:test { authentication-mode<K> }:authentication-mode { protocol<E><chap,pap> }:chap Command: pppoe simulate start 0 1 eth 4 100 user-name test@huawei user- password test authentication-mode chap huawei(config-if-gpon-0/1)# ---------------------------------- ONT PPPoE Test Result ----------------------------------...
  • Page 652 (HGW). Verify the voice service using call emulation. Run the ont emulational call command to configure a call emulation test. huawei(config)#test huawei(config-test)#ont emulational call caller-port 0/1/0 1 1 telno 77730020 { <cr>|caller-stop-time<K> }: Command: ont emulational call caller-port 0/1/0 1 1 telno 77730020 The ONT outputs the call emulation result after the test is complete.
  • Page 653 Run the igmp static-join command to simulate a multicast user to order a multicast program. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 1 ip 224.1.1.10 vlan 1000 NOTE If the multicast program is obtained dynamically, igmp static-join can be executed successfully only when the range for obtaining the dynamic program is set.

  • Page 654: Bridging Ont + Hgw Network Scenario

    16:33:41+08:00 ------------------------------------------------------------------------- Total: 1 Run the display multicast flow-statistic command to query the real-time traffic of the multicast program. huawei(config-btv)#display multicast flow-statistic vlan 1000 ip 224.1.1.10 { <cr>|sourceip<K> }: Command: display multicast flow-statistic vlan 1000 ip 224.1.1.10 Command is being executed. Please wait...

  • Page 655: Configuration Process

    (FTTH) networking using a bridging optical network terminal (ONT)+home gateway (HGW). Figure 9-4 Configuration roadmap in FTTH networking using a bridging ONT+HGW The following table describes the configuration steps. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 656: Adding An Ont To An Olt

    9.7.2.3 Adding an ONT to an OLT Services can be configured for an ONT only after the ONT is successfully added to an OLT. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 657 Run the display dba-profile command to query existing DBA profiles in the system. If the existing DBA profiles in the system do not meet the requirements, run the dba-profile add command to add a DBA profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 658 Create the same DBA profile for different types of services. Set the profile name to ftth_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to 20 Mbit/s. huawei(config)#dba-profile add profile-name ftth_dba type3 assure 8192 max 20480 NOTE The DBA implementation is based on an ONT.
  • Page 659 Add ONTs offline. If the password of an ONT is known, run the ont add command to add an ONT offline. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging omci ont-lineprofile-name ftth ont-srvprofile-name ftth huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging...

  • Page 660: Configuring The Internet Access Service

    The configuration processes on HGWs of different models or in different appearances are similar. This topic describes how to configure the Internet access service on an HG239 that is connected to an ONT upstream through a LAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 661 Set the profile ID to ftth_hsi, the CIR to 4 Mbit/s, and the priority to 0. In addition, configure the scheduling mode so that packets are scheduled according to their priorities. huawei(config)#traffic table ip name ftth_hsi cir 4096 priority 0 priority- policy local-setting Configure the mapping between a GEM port and a VLAN.
  • Page 662 100 0/19 0 Create Internet access service flows. Set S-VLAN ID to 100 and GEM port ID to 14. Use traffic profile ftth_hsi. huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi- service user-vlan 45 tag-transform translate-and-add inner-vlan 1001 inbound...

  • Page 663: Configuring The Voice Service

    This topic uses the HG255 that uses LAN for upstream transmission as examples. The IADs use SIP as the voice protocol. Data Plan Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 664 Set the profile name to ftth_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 665 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 47, and use traffic profile ftth_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi- service user-vlan 47 inbound traffic-table name ftth_voip outbound traffic-table...

  • Page 666: Configuring The Btv Service

    The VLAN of the LAN switch port connected to the OLT is the same as the upstream VLAN of the OLT. The ONT has been added to the OLT. For details, see 9.7.1.3 Adding an ONT to an OLT. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 667 Run the display traffic table ip command to query the existing traffic profiles in the system. If the existing traffic profiles in the system do not meet the requirements, run the traffic table ip command to add a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 668 Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to 1000, and use traffic profile 8. huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi- service user-vlan 1000 rx-cttr 8 tx-cttr 8...
  • Page 669 (Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic programs, perform this operation. For example, set the address range of dynamic programs to 224.1.1.1-224.1.1.100. huawei(config-mvlan1000)#igmp match group ip 224.1.1.1 to-ip 224.1.1.100 Set the IGMP mode. Select the IGMP proxy mode.

  • Page 670: Configuring The Vod Service

    The configuration processes on HGWs of different models or in different appearances are similar. This topic describes how to configure the Internet access service on an HG239 that is connected to an ONT upstream through a LAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 671 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 672 Set the service VLAN to 1100, GEM port ID to 13, and user VLAN to 41, and use traffic profile 8. huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 multi-service user-vlan 41 rx-cttr 8 tx-cttr 8 huawei(config)#service-port 4 vlan 1100 gpon 0/1/0 ont 2 gemport 13 multi-service user-vlan 41 rx-cttr 8 tx-cttr 8 Save the data.

  • Page 673: Configuring Link Aggregation, Congestion Control, And Security Policy

    QoS planning principles, see 11.2.2 Principle of QoS Data Plan. huawei(config)#queue-scheduler strict-priority huawei(config)#cos-queue-map cos0 0 cos4 4 cos5 5 cos6 6 Configure system security. – Enable deny of service (DoS) anti-attack on the OLT. Issue 01 (2014-04-30) Huawei Proprietary and Confidential...
  • Page 674 IP address anti-spoofing at the global level. In VLAN service profile mode, run the security anti-ipspoofing enable command to enable IP address anti-spoofing at the VLAN level. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 675 PITP at the global level. In the preceding commands, the enable, forward, and rebuild parameters can all enable PITP but provide different packet processing policies on the Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 676: Verifying Services

    ONT and BRAS. authentication mode must be configured on the BRAS for the PPPoE dialup emulation. l An ONT supports a maximum of a PPPoE dialup emulation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 677 Verify the Internet access service using PPPoE dialup emulation. In the xPON board mode, run the pppoe simulate start command to start a PPPoE dialup emulation test. The following test uses GPON as an example: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 678 { username<S><Length 1-64> }:test@huawei { user-password<K> }:user-password { password<S><Length 1-64> }:test { authentication-mode<K> }:authentication-mode { protocol<E><chap,pap> }:chap Command: pppoe simulate start 0 1 eth 4 100 user-name test@huawei user- password test authentication-mode chap huawei(config-if-gpon-0/1)# ---------------------------------- ONT PPPoE Test Result ----------------------------------...
  • Page 679 (HGW). Verify the voice service using call emulation. Run the ont emulational call command to configure a call emulation test. huawei(config)#test huawei(config-test)#ont emulational call caller-port 0/1/0 1 1 telno 77730020 { <cr>|caller-stop-time<K> }: Command: ont emulational call caller-port 0/1/0 1 1 telno 77730020 The ONT outputs the call emulation result after the test is complete.
  • Page 680 Run the igmp static-join command to simulate a multicast user to order a multicast program. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 1 ip 224.1.1.10 vlan 1000 NOTE If the multicast program is obtained dynamically, igmp static-join can be executed successfully only when the range for obtaining the dynamic program is set.

  • Page 681: Gateway Ont Network Scenario

    Point-to-Point Protocol over Ethernet (PPPoE)/DHCP dial-up, network address translation (NAT), and Internet Group Management Protocol (IGMP) snooping. This scenario provides fine-grained management channels and service control, and mainly applies to Layer 3 networking. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 682: Configuration Process

    (FTTH) networking using a gateway optical network terminal (ONT). Figure 9-6 Configuration roadmap in FTTH networking using a gateway ONT Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 683 IPTV services include the BTV and VoD IPTV service. Configuring services that are different in configuration the BTV procedures and need to be configured Service separately. 9.7.3.10 Configuring the VoD Service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 684: Adding An Ont To An Olt

    GEM port ID for Internet access services: 14 ONT service Profile name: ftth profile ONT port capability set: adaptive Network PON port: 0/1/0 topology data ONT IDs: 1 and 2 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 685 Create the same DBA profile for different types of services. Set the profile name to ftth_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to 20 Mbit/s. huawei(config)#dba-profile add profile-name ftth_dba type3 assure 8192 max 20480 NOTE The DBA implementation is based on an ONT.
  • Page 686 Add ONTs offline. If the password of an ONT is known, run the ont add command to add an ONT offline. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging omci ont-lineprofile-name ftth ont-srvprofile-name ftth huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging...
  • Page 687 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 9 FTTH Configuration huawei(config-if-gpon-0/1)#ont confirm 0 ontid 2 sn-auth 6877687714852901 omci ont-lineprofile-name ftth ont-srvprofile-name ftth NOTE If multiple ONTs of the same type bound to the same line profile or service profile are connected to the same port, you can bulk add ONTs by bulk confirming automatically discovered ONTs to make configuration easier and more efficient.

  • Page 688: Configuring The Internet Access Service (On A Web Page Or The U2000)

    If the traffic profiles existing in the system do not meet the requirements, you need to run the traffic table ip command to add a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 689 Set the profile ID to ftth_hsi, the CIR to 4 Mbit/s, and the priority to 0. In addition, configure the scheduling mode so that packets are scheduled according to their priorities. huawei(config)#traffic table ip name ftth_hsi cir 4096 priority 0 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 690 WAN port is bound to LAN1. – Set IP Acquisition Mode to PPPoE. – Select Enable NAT to enable the NAT function. (NAT must be enabled to configure the Internet access service.) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 691 From the main menu, choose Configuration > Access Profile Management. In the navigation tree of the tab page that is displayed, choose PON Profile > ONT VAS Profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 692 Choose General Type Config Info > WAN Device > WAN Device 1 > WAN Connection > WAN Connection 1 > WAN PPP Interface > WAN PPP Interface 1 and set parameters as follows: – WAN Interface Name: ONT-HSI Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 693 Add from the shortcut menu. Select Policy Route 1 and enter proper values. – Policy Route Type: SourcePhyPort – Physical Port Name: LAN1 – WAN Interface Name: WAN1(ONT-HSI) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 694: Configuring The H.248-Based Voice Service (On A Web Page Or The U2000)

    9.7.3.5 Configuring the H.248-based Voice Service (on a Web Page or the U2000) The OLT is connected to the remote ONT through a GPON port to provide users with the IP- based high-quality and low-cost VoIP service. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 695 Set the profile name to ftth_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 696 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 9 FTTH Configuration huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN. The service flow of user VLAN 300 is mapped to GEM port 12 in the ONT line profile.
  • Page 697 – Set VLAN ID to 300. (The VLAN ID of the ONT must be the same as the user-side VLAN ID configured on the OLT.) – Set 802.1p to 5. – Set IP Acquisition Mode to DHCP. Click Apply. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 698 Start Number of RTP TID, and Width of RTP TID Number. Configure parameters for H.248-based voice users. Choose Voice > VoIP Basic Configuration. In the Basic User Parameters(H.248) window, set the parameters for user 1 as follows: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 699 From the main menu, choose Configuration > Access Profile Management. In the navigation tree of the tab page that is displayed, choose PON Profile > ONT VAS Profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 700 Service 1 > Interface configuration > Interface 1. Select Interface 1 and select a proper value. – Signaling Protocol: H.248 – Associate WAN Interface: WAN1 (binding the created voice WAN port) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 701 In the navigation tree, choose General Para > Services > Voice Service > Voice Service 1 > Interface configuration > Interface 1 > User. Right- click User and choose Add from the shortcut menu. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 702 WAN Connection > WAN Connection 1 > WAN IP Interface > WAN IP Interface 1 from the navigation tree, and set WAN Interface Name to ONT- VoIP, Service Type to VOIP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 703 Pay attention to the RTP TID configuration when the ONT is interconnected with a softswitch of other vendors. The terminal IDs A0 and A1 must be consistent with the corresponding configuration on the MGC. Do not configure Directory Number. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 704: Configuring The H.248-Based Voice Service (Through The Cli)

    The ONT software version of the H.248 voice service can be configured as V100R002C04 or later through the CLI. Context Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 705 Set the service VLAN to 200, GEM port ID to 12, and user VLAN to 300. Use traffic profile ftth_voip. huawei(config)#service-port vlan 200 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name ftth_voip outboun d traffic-table name ftth_voip...
  • Page 706 For ONT 1 and ONT 2, configure the IP address obtaining mode to DHCP mode, set the management VLAN to VLAN 20, and use default values for other parameters. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20 huawei(config-if-gpon-0/1)#ont ipconfig 0 2 dhcp vlan 20 Step 8 Configure H.248 POTS users.
  • Page 707 For ONT 1 and ONT 2, create a POTS user, set the MG ID to 1 (identical to the MG ID of the H.248 interface), and set the physical terminal port ID to A0 and A1. huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 1 mgid 1 terminalid A0 huawei(config-if-gpon-0/1)#mgpstnuser add 0 2 1 mgid 1 terminalid A1 Run the display mgpstnuser attribute command to check whether the configuration of the POTS user is properly set.

  • Page 708: Configuring The Sip-Based Voice Service (On A Web Page Or The U2000)

    ONTs have the same C-VLAN. The ONT adds a C-VLAN tag to packets. l OLT: translates the VLAN tag (C-VLAN <-> S- VLAN). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 709 Set the profile name to ftth_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 710 – Set VLAN ID to 300. (The VLAN ID of the ONT must be the same as the user-side VLAN ID configured on the OLT.) – Set 802.1p to 5. – Set IP Acquisition Mode to DHCP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 711 Choose Voice > VoIP Basic Configuration. In the Basic Interface Parameters(SIP) window, configure the parameters as follows: – Set Address of the Primary Proxy Server to 200.200.200.200. – Set Home Domain to huawei.com. – Set Region to China. – Set Signaling Port to 1_VOIP_R_VID_300. NOTE l The parameters of the SIP-based voice interface must be consistent with the corresponding configuration on the softswitch.
  • Page 712 – Set Registration User Name to 77730010. – Set Associated POTS Port to 1. – Set Authentication User Name to +8675577730010@huawei.com. – Set Password to iadtest1. Click New to add voice user 2, and set the parameters for voice user 2 as follows: –...
  • Page 713 Device 1 > WAN Connection. Select WAN Connection, right-click, and choose Add IP Connection from the shortcut menu. Select WAN IP Interface 1 and enter (or select) a proper value. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 714 Service 1 > Interface configuration > Interface 1 > SIP. Select SIP and enter (or select) a proper value. – Proxy Server: 200.200.200.200 – Server Port: 5060 – Home Domain: huawei.com Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 715 ONT is bound. Click Next. In the dialog box that is displayed, set vendor ID to HWTC, Terminal Type to General Type, and Version to V1R003C00-ZZ, click Add. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 716 Select an ONT from the list, right-click, and choose Bind General VAS Profile from the shortcut menu. In the dialog box that is displayed, select the created profile, and click OK to complete profile binding. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 717: Configuring The Sip-Based Voice Service (Through The Cli)

    SIP server. The connection between the OLT and the SIP server is set up. The OLT can ping the IP address of the SIP server successfully. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 718 Step 2 Configure the mapping relationship between a GEM port and a VLAN. The service flow of user VLAN 300 is mapped to GEM port 12 in the ONT line profile. huawei(config)#ont-lineprofile gpon profile-name ftth huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 300 Issue 01 (2014-04-30) Huawei Proprietary and Confidential...
  • Page 719 Set the service VLAN to 200, GEM port ID to 12, and user VLAN to 300. Use traffic profile ftth_voip. huawei(config)#service-port vlan 200 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name ftth_voip outboun d traffic-table name ftth_voip...
  • Page 720 POTS users named huawei1 and huawei2, set passwords to user1 and user2, set their phone numbers to 77730010 and 77730020 and use default values for other parameters. huawei(config-if-gpon-0/1)#sippstnuser add 0 1 1 mgid 1 username huawei1 telno 77730010 huawei(config-if-gpon-0/1)#sippstnuser add 0 2 1 mgid 1 username huawei2 telno...
  • Page 721 Access Module Commissioning and Configuration Guide 9 FTTH Configuration Run the display sippstnuser attribute command to check whether the configuration of the POTS user is properly set. huawei(config-if-gpon-0/1)#display sippstnuser attribute 0 1 1 ------------------------------------------------------------------------------ F/S/P : 0/1/0 ONT ID Port ID MG ID Telephone NO.

  • Page 722: Configuring The Btv Service

    9.7.1.3 Adding an ONT to an OLT. Data Plan Table 9-6 Data plan Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 13 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 723 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and an Ethernet port on the ONT.
  • Page 724 Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to 1000, and use traffic profile 8. huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi- service user-vlan 1000 rx-cttr 8 tx-cttr 8...

  • Page 725: Configuring The Vod Service

    The ONT has been added to the OLT. For details, see 9.7.1.3 Adding an ONT to an OLT. Data Plan Item Data ONT line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 13 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 726 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and a VLAN.

  • Page 727: Configuring Link Aggregation, Congestion Control, And Security Policy

    8. Set the VLAN translation policy to Translate. The C-VLAN 2001 of the ONT is translated to S-VLAN 1100. huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 multi-service user-vlan 2001 tag-transform translate rx-cttr 8 tx-cttr 8...
  • Page 728 IP address anti-spoofing at the global level. In VLAN service profile mode, run the security anti-ipspoofing enable command to enable IP address anti-spoofing at the VLAN level. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 729 PITP at the global level. In the preceding commands, the enable, forward, and rebuild parameters can all enable PITP but provide different packet processing policies on the Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 730: Verifying Services

    ONT and BRAS. authentication mode must be configured on the BRAS for the PPPoE dialup emulation. l An ONT supports a maximum of a PPPoE dialup emulation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 731 Verify the Internet access service using PPPoE dialup emulation. In the xPON board mode, run the pppoe simulate start command to start a PPPoE dialup emulation test. The following test uses GPON as an example: Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 732 { username<S><Length 1-64> }:test@huawei { user-password<K> }:user-password { password<S><Length 1-64> }:test { authentication-mode<K> }:authentication-mode { protocol<E><chap,pap> }:chap Command: pppoe simulate start 0 1 eth 4 100 user-name test@huawei user- password test authentication-mode chap huawei(config-if-gpon-0/1)# ---------------------------------- ONT PPPoE Test Result ----------------------------------...
  • Page 733 (HGW). Verify the voice service using call emulation. Run the ont emulational call command to configure a call emulation test. huawei(config)#test huawei(config-test)#ont emulational call caller-port 0/1/0 1 1 telno 77730020 { <cr>|caller-stop-time<K> }: Command: ont emulational call caller-port 0/1/0 1 1 telno 77730020 The ONT outputs the call emulation result after the test is complete.
  • Page 734 Run the igmp static-join command to simulate a multicast user to order a multicast program. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 1 ip 224.1.1.10 vlan 1000 NOTE If the multicast program is obtained dynamically, igmp static-join can be executed successfully only when the range for obtaining the dynamic program is set.

  • Page 735: Configuring Triple Play Service (Simplified Mode)

    FTTH triple play service. Figure 9-7 Example network of the FTTH triple play service Prerequisite The OLT is connected to the BRAS, MGC, and the multicast source. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 736 0100000002, the discovery mode of passwords is once-on, and the management mode is OMCI. Add ONTs offline. If the password of an ONT is known, run the ont add command to add an ONT offline. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 737 SmartAX MA5600T/MA5603T/MA5608T Multi-service Access Module Commissioning and Configuration Guide 9 FTTH Configuration huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 1 1 password-auth 0100000001 once- on no-aging omci huawei(config-if-gpon-0/1)#ont add 1 2 password-auth 0100000002 once- on no-aging omci Discover ONTs automatically. If the password or SN of an ONT is unknown, run the port portid ont-auto- find command in GPON mode to enable the ONT auto-discovery function of the GPON port.
  • Page 738 Set the profile ID to 8, the CIR to 4 Mbit/s, and the priority to 1. In addition, configure the scheduling mode so that packets are scheduled according to their priorities. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 739 NOTICE The user PC is connected to the ONT port. Therefore, the user-side VLAN is set to untagged. huawei(config)#service-port 1 vlan 100 port 0/1/1 ont 1 eth 1 multi- service user-vlan untagged inbound traffic-table index 8 outbound traffic- table index 8...
  • Page 740 If the STB interconnected to the ONT does not support VLAN tag, the user-side VLAN is set to untagged when creating service port. huawei(config)#service-port 5 vlan 1000 port 0/1/1 ont 1 eth 2 multi- service user-vlan 30 inbound traffic-table index 10 outbound traffic-table...
  • Page 741 Configure a program library. Configure the IP address of the multicast program to 224.1.1.10, program name to program1, and program source IP address to 10.10.10.10. huawei(config-btv)#multicast-vlan 1000 huawei(config-mvlan1000)#igmp program add name program1 ip 224.1.1.10 sourceip 10.10.10.10 Configure a right profile.

  • Page 742: P2P Access: Configuring Ftth Service

    Table 9-7 Data plan for configuring the VLANs Configuration Item Data Item Data SVLAN HSI service SVLAN: 100 CVLAN: 2 IPTV service SVLAN: 1000 CVLAN: 4 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 743 Because the VoIP, IPTV, and Internet access services are provided through the same port, you must set the 802.1p priority of each service. Generally, the priorities are in Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 744 10 10 20 20 40 0 0 0 Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map queues 0-7 respectively. huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 cos7 7 NOTE For the service board that supports only four queues, the mapping between 802.1p priorities and...
  • Page 745 1000 0/19 0 Configure a traffic profile. The traffic profile index is 9, and the 802.1p priority of the IPTV service is 5. huawei(config)#traffic table ip index 9 cir off priority 5 priority- policy local-Setting Configure a service port.
  • Page 746 Configure the program names to BTV-1 and BTV-2, multicast IP addresses of the programs to 224.1.1.10 and 224.1.1.20, and source IP address of the programs to 10.10.10.10. huawei(config-btv)#multicast-vlan 1000 huawei(config-mvlan1000)#igmp program add name BTV-1 ip 224.1.1.10 sourceip 10.10.10.10 huawei(config-mvlan1000)#igmp program add name BTV-2 ip 224.1.1.20 sourceip 10.10.10.10...
  • Page 747 300 vlan 1000 eth 0/5/3 multi-service user-vlan 4 rx-cttr 9 tx-cttr 9 dhcp mode layer-3 option-60 dhcp-server 2 ip 20.2.2.2 20.2.2.3 dhcp domain video dhcp-server 2 quit interface vlanif 1000 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 748 300 auth igmp user bind-profile service-port 300 profile-name profile0 multicast-vlan 1000 igmp multicast-vlan member service-port 200 igmp multicast-vlan member service-port 300 quit save Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 749: Fttd Configuration

    (OLT) and optical network unit (ONU) hardware configurations. 10.4 Reference of GPON ONU Capability Sets This section provides common Huawei GPON optical network unit (ONU) capability sets, serving as a reference for parameter configuration when an ONU is added offline.

  • Page 750: Fttd Service Overview

    The ONUs can be installed in shafts or garages, or mounted to courtyard walls. The ONUs access users to provide voice, Internet access, and multicast services. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 751 It provides multiple service ports, such as POTS and LAN, wireless local area network (WLAN), or xDSL ports. The HGW supports routing and remote management and diagnosis. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 752: Networking Scenarios And Hardware Configurations (Gpon)

    10.3 Networking Scenarios and Hardware Configurations (GPON) This section describes GPON fiber to the door (FTTD) networking scenarios and typical optical line terminal (OLT) and optical network unit (ONU) hardware configurations. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 753 IAD provides Internet, voice over Internet Protocol Network (VoIP), and Internet Scenario Protocol television (IPTV) (MA5651 services to users. Services are implemented on MA5651 the HGW, and the bridging Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 754 Commissioning and Configuration Guide 10 FTTD Configuration Network Description Typical OLT ONU Device Configuration Scenario ONU works with the OLT to MA5651 or provide Layer 2 channels. MA5651S Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 755: Reference Of Gpon Onu Capability Sets

    Commissioning and Configuration Guide 10 FTTD Configuration 10.4 Reference of GPON ONU Capability Sets This section provides common Huawei GPON optical network unit (ONU) capability sets, serving as a reference for parameter configuration when an ONU is added offline. Prod...

  • Page 756: Principle Of Fttd Data Plan

    The QoS planning is an E2E planning, and it can be divided into following policies: traffic classification, marking, and scheduling policy; and traffic monitoring and DBA policy. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 757 Rate limit on No rate limit Configure rate No rate limit No rate limit limit by a traffic downstream profile as required. [Remark 2] Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 758 (in the case of multiple STBs). The upstream bandwidth is mainly used for transmitting IGMP packets, which requires little bandwidth. Therefore, the bandwidth occupied by IGMP packets can be neglected. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 759: Principle Of Internet Access Service Data Plan

    C-VLAN tag to packets. All ONUs are in the same C-VLAN. OLT: The OLT performs VLAN translation: C<->S+C'. The C'-VLAN of every ONU differs from each other. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 760: Principle Of Voice Service Data Plan

    10.5.4 Principle of Voice Service Data Plan The voice service plan mainly includes the plan of the VLAN and VLAN translation policy in different network scenario, and the plan of voice protocol. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 761 Media and Upstream VLANs of the VoIP service interface/ signaling upstream signalin VLANs interface Media and Uplink ports of the VoIP service data paramet signaling uplink port Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 762 Terminal ID (H248) If the TID template with which the POTS user is bound does not support terminal layering, this parameter needs to be configured. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 763: Principle Of Iptv Service Data Plan

    The OLT replicates multicast packets based on PON ports with M-VLAN unchanged. Single- ONUs add S-VLAN tags to iTV service tagged packets. VLAN The OLT transparently transmits packets with S-VLANs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 764 C<->S+C': Bidirectional VLAN translation: translates the inner C-VLAN and then adds one outer S-VLAN. C<->S+C: Bidirectional VLAN translation: maintains the inner C-VLAN and adds one outer S-VLAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 765: Gpon Access: Configuring Fttd Service

    10.6.1 Bridging+Voice ONU Network Scenario (MA5652S) This topic describes how to configure Internet access service, voice service, BTV service and VoD service when bridging+voice ONUs are used to build an FTTD network. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 766: Service Requirements And Application Scenario

    (IMS). Figure 10-1 Bridging+Voice ONU 10.6.1.2 Configuration Process Figure 10-2 shows the configuration roadmap in fiber to the door (FTTD) networking using a bridging+voice optical network unit(ONU). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 767 10.6.1.4 Configuring a VDSL2 Services can be transmitted only after a User Port VDSL2 port on an optical network unit (ONU) is activated. 10.6.1.5 Configuring the Internet None Access Service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 768 The OLT provides remote verification methods including ONU PPPoE/DHCP dialup emulation and call emulation for configuration and commissioning engineers to verify services remotely after service configuration, avoiding a second on-site operation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 769: Adding An Onu To An Olt

    ONU lines. When a statistical value reaches the threshold, the host is notified and an alarm is reported to the log host and the NMS. Configure a DBA profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 770 Create the same DBA profile for different types of services. Set the profile name to fttd_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to 20 Mbit/s. huawei(config)#dba-profile add profile-name fttd_dba type3 assure 8192 max 20480 NOTE The DBA implementation is based on an ONU.
  • Page 771 Add ONUs offline. If the password of an ONU is known, run the ont add command to add an ONU offline. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging omci ont-lineprofile-name fttd ont-srvprofile-name fttd l Confirm automatically discovered ONUs If the password or SN of an ONU is unknown, run the port portid ont-auto-find enable command in GPON mode to enable the ONU auto-discovery function of the GPON port.

  • Page 772: Configuring A Vdsl2 User Port

    (Optional) Bind the alarm profile to the ONU. The default profile 1 is used in this example. huawei(config-if-gpon-0/1)#ont alarm-profile 0 1 profile-id 1 Step 3 Check ONU status. After an ONU is added, run the display ont info command to query the current status of the ONU.
  • Page 773 500 m. Maximum transmit 100 Mbit/ 50 Mbit/s 40 Mbit/s 25 Mbit/s 20 Mbit/s l Limiting rate downstream upstream downstrea m rates ensures a higher signal-to- Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 774 Minimum INP 2 symbols 2 symbols 2 symbols 2 symbols 2 symbols None Target SNR margin 8 dB 8 dB 8 dB 8 dB 8 dB None Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 775 VDSL2 line profile in TR129 mode. Figure 10-4 Flowchart for configuring a VDSL2 line profile in TR129 mode Figure 10-5 shows the process for configuring a VDSL2 line profile in TR165 mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 776 Figure 10-5 Flowchart for configuring a VDSL2 line profile in TR165 mode Procedure Step 1 (Optional) Run the command in Figure 10-4 Figure 10-5 to configure a VDSL2 line profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 777: Configuring The Internet Access Service

    Networking data PON port: 0/1/0 ONU ID: 1 In TR129 mode: huawei(config-if-gpon-0/1)#ont port activate 0 1 vdsl-port 1 template-index 1 In TR165 mode: huawei(config-if-gpon-0/1)#ont port activate 0 1 vdsl-port 1 ----End 10.6.1.5 Configuring the Internet Access Service An optical line terminal (OLT) is connected to a remote optical network unit (ONU) through a GPON port to provide users with high-speed Internet access services.
  • Page 778 8 name fttd_hsi cir off priority 4 priority-policy local-setting Configure the mapping between a GEM port and a VLAN.
  • Page 779 100 0/19 0 Create Internet access service flows. Set S-VLAN ID to 100 and GEM port ID to 14. Use traffic profile fttd_hsi. huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi- service user-vlan 45 tag-transform translate-and-add inner-vlan 1001 inbound...

  • Page 780: Configuring The H.248-Based Voice Service (Through The Cli)

    ONU software version supports H.248. For details, see relevant ONU manuals. Data Plan Item Data ONU line profile Profile name: fttd T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 781 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 300, and use traffic profile fttd_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name fttd_voip outbound traffic-table name...
  • Page 782 10.10.10.10/24, set the management VLAN to VLAN 20, and use default values for other parameters. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20 Step 8 Configure H.248 POTS users. Add an H.248 interface and apply an MGC interface profile to the interface.
  • Page 783 Add POTS users 1 and 2 to ONU 1, set the MG ID to 1 (identical to the MG ID of the H. 248 interface), and set the physical terminal port ID to A0 and A1. huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 1 mgid 1 terminalid A0 huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 2 mgid 1 terminalid A1 Run the display mgpstnuser attribute command to check whether the configuration of the POTS user is properly set.

  • Page 784: Configuring The H.248-Based Voice Service (On A Web Page)

    ONU: provides the VoIP service and uses the same SVLAN. Voice parameter IP address of the MGC server: 200.200.200.200/24 Port ID of the MGC server: 2944 Procedure Configure the OLT. Configure a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 785 Set the profile name to fttd_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name fttd_voip cir off priority 5 priority- policy local-setting Configure the mapping between a GEM port and a VLAN.
  • Page 786 – Set 802.1p to 5. – Set IP Acquisition Mode to DHCP. Figure 10-6 shows the parameter settings. Figure 10-6 Parameter settings on the Web page for the voice WAN interface Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 787 MGC type. Profile Index is set to Default (indicating interconnection with Huawei MGC) in this example. If the settings do not meet requirements, configure UserDefine. For details about how to configure this parameter, contact Huawei technical support engineers.
  • Page 788 The terminal IDs A0 and A1 must be consistent with the corresponding configuration on the MGC. l If Associated POTS is 1, port TEL1 on the ONU is bound. If Associated POTS is 2, port TEL2 on the ONU is bound. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 789 Check the ONU connection status. In the navigation tree, choose Status > WAN Information. In the right pane, Status is Connected and the obtained IP address is displayed at IP Address. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 790: Configuring The Sip-Based Voice Service (Through The Cli)

    ONU software version supports SIP. For details, see relevant ONU manuals. Data Plan Item Data ONU line profile Profile name: ftth T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 791 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 300, and use traffic profile fttd_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service user-vlan 300 inbound traffic-table name fttd_voip outbound traffic-table name...
  • Page 792 Run the display ont-digitmap-profile command to query the existing digitmap profile in the system. If the existing digitmap profile in the system does not meet the requirements, run the ont-digitmap-profile add command to add a digitmap profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 793 POTS users named huawei1, set passwords to user1 and user2, set their phone numbers to 77730010 and 77730020 and use default values for other parameters. huawei(config-if-gpon-0/1)#sippstnuser add 0 1 1 mgid 1 username huawei1 telno 77730010 huawei(config-if-gpon-0/1)#sippstnuser add 0 2 1 mgid 1 username huawei2 telno...
  • Page 794 Run the sippstnuser codec command to configure the SIP user codec. The SIP user codec will not be configured independently in this example. Step 10 Save the data. huawei(config)#save ----End Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 795: Configuring The Sip-Based Voice Service (On A Web Page)

    Port ID of the SIP server: 5060 Home domain name: huawei.com User phone number 1: 77730010 User phone number 2: 77730020 Procedure Configure the OLT. Configure a traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 796 Set the profile name to fttd_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name fttd_voip cir off priority 5 priority- policy local-setting Configure the mapping between a GEM port and a VLAN.
  • Page 797 – Set 802.1p to 5. – Set IP Acquisition Mode to DHCP. Figure 10-8 shows the parameter settings. Figure 10-8 Parameter settings on the Web page for the voice WAN interface Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 798 Port. When the packet is forwarded from two WAN ports, the configured VLAN is carried by default. Click . The configuration takes effect. Configure parameters of the SIP-based voice users. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 799 ONU is bound. Save the data. huawei(config)#save Restart the voice process. In the navigation tree, choose Status > VoIP Information. In the right pane, click Restart VoIP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 800: Configuring The Btv Service

    10.6.1.4 Configuring a VDSL2 User Port. Data Plan Table 10-4 Data plan Item Data ONU line profile Profile name: fttd T-CONT ID: 4 GEM port ID: 13 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 801 Run the display traffic table ip command to query the existing traffic profiles in the system. If the existing traffic profiles in the system do not meet the requirements, run the traffic table ip command to add a traffic profile. huawei(config)#traffic table ip index 8 cir off priority 4 priority- policy local-setting Configure the mapping relationship between a GEM port and a VDSL2 port on the ONU.
  • Page 802 Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to 1000, and use traffic profile 8. huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi- service user-vlan 1000 rx-cttr 8 tx-cttr 8 Create an MVLAN and configure the IGMP version.
  • Page 803 (Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic programs, perform this operation. For example, set the address range of dynamic programs to 224.1.1.1-224.1.1.100. huawei(config-mvlan1000)#igmp match group ip 224.1.1.1 to-ip 224.1.1.100 Set the IGMP mode. Select the IGMP proxy mode.

  • Page 804: Configuring The Vod Service

    A VDSL2 port has been activated. For details, see 10.6.1.4 Configuring a VDSL2 User Port. Data Plan Item Data ONU line profile Profile name: fttd T-CONT ID: 4 GEM port ID: 13 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 805 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and a VDSL2 port on the ONU.
  • Page 806 Set the service VLAN to 1100, GEM port ID to 13, and user VLAN to 43, and use traffic profile 8. huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 multi-service user-vlan 43 rx-cttr 8 tx-cttr 8 Save the data.

  • Page 807: Verifying Services

    ONU. You can check whether the multicast service is normal by checking the real-time traffic of the multicast program. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 808 { username<S><Length 1-64> }:test@huawei { user-password<K> }:user-password { password<S><Length 1-64> }:test { authentication-mode<K> }:authentication-mode { protocol<E><chap,pap> }:chap Command: pppoe simulate start 0 1 vdsl 1 100 user-name test@huawei user- password test authentication-mode chap huawei(config-if-gpon-0/1)# ---------------------------------- ONT PPPoE Test Result ----------------------------------...
  • Page 809 (HGW). Verify the voice service using call emulation. Run the ont emulational call command to configure a call emulation test. huawei(config)#test huawei(config-test)#ont emulational call caller-port 0/1/0 1 1 telno 28777192 { <cr>|caller-stop-time<K> }: Command: ont emulational call caller-port 0/1/0 1 1 telno 28777192 The ONU outputs the call emulation result after the test is complete.
  • Page 810 Run the igmp static-join command to simulate a multicast user to order a multicast program. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 1 ip 224.1.1.10 vlan 1000 NOTE If the multicast program is obtained dynamically, igmp static-join can be executed successfully only when the range for obtaining the dynamic program is set.

  • Page 811: Bridging Onu Network Scenario (Ma5651/Ma5651S)

    16:33:41+08:00 ------------------------------------------------------------------------- Total: 1 Run the display multicast flow-statistic command to query the real-time traffic of the multicast program. huawei(config-btv)#display multicast flow-statistic vlan 1000 ip 224.1.1.10 { <cr>|sourceip<K> }: Command: display multicast flow-statistic vlan 1000 ip 224.1.1.10 Command is being executed. Please wait...

  • Page 812: Configuration Process

    (FTTD) networking using a bridging optical network unit (ONU)+home gateway (HGW). Figure 10-10 Configuration roadmap in FTTD networking using a bridging ONU+HGW The following table describes the configuration steps. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 813: Adding An Onu To An Olt

    (OLT). Data Plan Table 10-5 Data plan Item Data DBA profile Profile name: fttd_dba Profile type: type3 Assured bandwidth: 8 Mbit/s Maximum bandwidth: 20 Mbit/s Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 814 Create the same DBA profile for different types of services. Set the profile name to fttd_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to 20 Mbit/s. huawei(config)#dba-profile add profile-name fttd_dba type3 assure 8192 max 20480 NOTE The DBA implementation is based on an ONU.
  • Page 815 GEM port 12 is used to carry voice services. l GEM port 13 is used to carry video services. l GEM port 14 is used to carry Internet access services. huawei(config-gpon-lineprofile-1)#gem add 11 eth tcont 4 huawei(config-gpon-lineprofile-1)#gem add 12 eth tcont 4 huawei(config-gpon-lineprofile-1)#gem add 13 eth tcont 4...
  • Page 816 Add ONUs offline. If the password of an ONU is known, run the ont add command to add an ONU offline. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging omci ont-lineprofile-name fttd ont-srvprofile-name fttd l Confirm automatically discovered ONUs If the password or SN of an ONU is unknown, run the port portid ont-auto-find enable command in GPON mode to enable the ONU auto-discovery function of the GPON port.

  • Page 817: Configuring A Vdsl2 User Port

    VDSL2 line (26 AWG, 0.4 mm twisted pair). Information provided in this table is for reference only. Usually, take the default values for the other parameters. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 818 (SNR) margin for the line and therefore enhances capability withstandin g noise and interferenc l The rates can be specified using these parameters and also can be Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 819 Minimum INP 2 symbols 2 symbols 2 symbols 2 symbols 2 symbols None Target SNR margin 8 dB 8 dB 8 dB 8 dB 8 dB None Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 820 VDSL2 line profile in TR129 mode. Figure 10-12 Flowchart for configuring a VDSL2 line profile in TR129 mode Figure 10-13 shows the process for configuring a VDSL2 line profile in TR165 mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 821 Figure 10-13 Flowchart for configuring a VDSL2 line profile in TR165 mode Procedure Step 1 (Optional) Run the command in Figure 10-12 Figure 10-13 to configure a VDSL2 line profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 822: Configuring The Internet Access Service

    Networking data PON port: 0/1/0 ONU ID: 1 In TR129 mode: huawei(config-if-gpon-0/1)#ont port activate 0 1 vdsl-port 1 template-index 1 In TR165 mode: huawei(config-if-gpon-0/1)#ont port activate 0 1 vdsl-port 1 ----End 10.6.2.5 Configuring the Internet Access Service An optical line terminal (OLT) is connected to a remote optical network unit (ONU) through a GPON port to provide users with high-speed Internet access services.
  • Page 823 8 name fttd_hsi cir off priority 4 priority-policy local-setting Configure the mapping between a GEM port and a VLAN.
  • Page 824 100 0/19 0 Create Internet access service flows. Set S-VLAN ID to 100 and GEM port ID to 14. Use traffic profile fttd_hsi. huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi- service user-vlan 45 tag-transform translate-and-add inner-vlan 1001 inbound...

  • Page 825: Configuring The Voice Service

    This topic uses the HG255 that uses LAN for upstream transmission as examples. The IADs use SIP as the voice protocol. Data Plan Item Data ONU line profile Profile name: fttd T-CONT ID: 4 GEM port ID: 12 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 826 Set the profile name to fttd_voip and do not limit the upstream and downstream rates. Set the priority to 5 and packets are scheduled according to the priority carried. huawei(config)#traffic table ip name fttd_voip cir off priority 5 priority- policy local-setting Configure the mapping relationship between a GEM port and a VLAN.
  • Page 827 Set the service VLAN to 300, GEM port ID to 12, and user VLAN to 45, and use traffic profile fttd_voip. huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi- service user-vlan 45 inbound traffic-table name fttd_voip outbound traffic-table...

  • Page 828: Configuring The Btv Service

    The ONU has been added to the OLT. For details, see 10.6.2.3 Adding an ONU to an OLT. A VDSL2 port has been activated. For details, see 10.6.1.4 Configuring a VDSL2 User Port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 829 Run the display traffic table ip command to query the existing traffic profiles in the system. If the existing traffic profiles in the system do not meet the requirements, run the traffic table ip command to add a traffic profile. huawei(config)#traffic table ip index 8 cir off priority 4 priority- policy local-setting...
  • Page 830 Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to 1000, and use traffic profile 8. huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi- service user-vlan 1000 rx-cttr 8 tx-cttr 8 Create an MVLAN and configure the IGMP version.
  • Page 831 (Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic programs, perform this operation. For example, set the address range of dynamic programs to 224.1.1.1-224.1.1.100. huawei(config-mvlan1000)#igmp match group ip 224.1.1.1 to-ip 224.1.1.100 Set the IGMP mode. Select the IGMP proxy mode.

  • Page 832: Configuring The Vod Service

    The configuration processes on HGWs of different models or in different appearances are similar. This topic describes how to configure the Internet access service on an HG239 that is connected to an ONT upstream through a LAN. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 833 8 cir off priority 4 priority-policy local-setting Configure the mapping relationship between a GEM port and a VDSL2 port on the ONU.
  • Page 834 Set the service VLAN to 1100, GEM port ID to 13, and user VLAN to 43, and use traffic profile 8. huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 multi-service user-vlan 43 rx-cttr 8 tx-cttr 8 Save the data.

  • Page 835: Verifying Services

    ONU. You can check whether the multicast service is normal by checking the real-time traffic of the multicast program. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 836 { username<S><Length 1-64> }:test@huawei { user-password<K> }:user-password { password<S><Length 1-64> }:test { authentication-mode<K> }:authentication-mode { protocol<E><chap,pap> }:chap Command: pppoe simulate start 0 1 vdsl 1 100 user-name test@huawei user- password test authentication-mode chap huawei(config-if-gpon-0/1)# ---------------------------------- ONT PPPoE Test Result ----------------------------------...
  • Page 837 Run the igmp static-join command to simulate a multicast user to order a multicast program. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 1 ip 224.1.1.10 vlan 1000 NOTE If the multicast program is obtained dynamically, igmp static-join can be executed successfully only when the range for obtaining the dynamic program is set.
  • Page 838 16:33:41+08:00 ------------------------------------------------------------------------- Total: 1 Run the display multicast flow-statistic command to query the real-time traffic of the multicast program. huawei(config-btv)#display multicast flow-statistic vlan 1000 ip 224.1.1.10 { <cr>|sourceip<K> }: Command: display multicast flow-statistic vlan 1000 ip 224.1.1.10 Command is being executed. Please wait...

  • Page 839: Fttb And Fttc Solution Configuration

    This section describes how to configure services when a multi-dwelling unit (MDU) serving as an independent node or GE remote extended subrack cascades with an optical line terminal (OLT)through Ethernet port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 840: Fttb And Fttc Service Overview

    Figure 11-2 Integrated FTTB and FTTC network diagram (Ethernet cascading) PE-AGG NGN/IMS FE/GE IPTV Metro Network Headend FE/GE Laptop Phone Internet FE/GE PE-AGG Phone User Side Access Side Network Side Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 841 ONUs are located on the user side, providing various types of ports for connecting to user terminals. The ONUs communicate with the OLT through a passive ODN. NOTE ONUs in FTTB and FTTC networks refer to multi-dwelling units (MDUs). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 842 The IP multimedia subsystem (IMS) uses SIP signaling as its call control signaling to provide services such as VoIP, data, and multimedia services. NOTE NGN/IMS in this document refers to softswitches that support H.248 and SIP. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 843: Scenario And Hardware Configuration (Gpon)

    MA5622A, Access home through the twisted MA5603T Without pair cable. HGW) l The ONU provides xDSL and POTS ports for the Internet access and VoIP services. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 844 The HGW provides the l ONUs with xDSL Internet access and IPTV ports include services by connecting to MA5616, the upstream ONU using MA5622A, LAN or xDSL. MA5603T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 845 ONUs with ADSL2+ ports include MA5616, MA5603T. l ONUs with VDSL2 ports include MA5616, MA5622A, MA5623, MA5623A, MA5611S-AE16, MA5611S-AE16 (No SPL), MA5611S-DE16, MA5611S-DE48 (900-ohm impedance), MA5611S-DE48, Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 846: Scenario And Hardware Configuration (10G Gpon)

    IAD of the ONU provides the VoIP service. l The HGW provides the Internet access and IPTV services by connecting to the upstream ONU using LAN or xDSL. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 847: Networking Scenarios And Hardware Configurations (Ethernet Cascading)

    NEs on the network. The GE remote extended subrack networking reduces the OPEX and total cost of operation (TCO) of carriers. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 848 X1CA, or service, and IPTV service. X2CA In the scenarios, an HGW is configured on the user side and VDSL2 is used for downstream transmission. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 849: Gpon Onu Capability Sets

    This topic describes the hardware capabilities and usage scenarios of GPON optical network units (ONUs) on fiber to the building (FTTB) or fiber to the curb (FTTC) networks. Table 11-1 shows the GPON ONU capability sets provided by Huawei. NOTE The Service Port column in...
  • Page 850 V800R31 2C00 l V800R01 5C00 MA5612A l GE electrical ports l V800R30 8C00 l FE electrical ports l V800R31 0C00 l V800R31 2C00 l V800R01 5C00 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 851 GE electrical ports board) 2C00 l ADSL2+ ports l V800R31 l VDSL2 ports (Supports vectoring) 3C00 l SHDSL ports l V800R01 l POTS ports 5C00 l ISDN ports Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 852 V800R015C The MA5611S DE48 (900- applies to FTTB and FTTC impedance) scenarios. MA5611S- VDSL2 ports (Supports vectoring) V800R015C The MA5611S DE48 applies to FTTB and FTTC scenarios. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 853: Gpon Onu Capability Sets

    V800R313C It is mainly used on specifications: FTTB networks. l 1: 8 FE electrical ports l 2: 16 FE electrical ports l 3: 24 FE electrical ports Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 854: Ethernet Upstream Onu Capability Sets

    This topic describes the hardware capabilities and usage scenarios of optical network units (ONUs) for Ethernet upstream transmission on fiber to the building (FTTB) or fiber to the curb (FTTC) networks. Table 11-3 shows the Ethernet upstream ONU capability sets provided by Huawei. NOTE The Service Port column in Table 11-3 lists only service ports supported by all configurations of an ONU type.
  • Page 855 V800R31 2C00 l V800R01 5C00 MA5612A l GE electrical ports l V800R30 8C00 l FE electrical ports l V800R31 0C00 l V800R31 2C00 l V800R01 5C00 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 856 GE electrical ports board) 2C00 l ADSL2+ ports l V800R31 l VDSL2 ports (Supports vectoring) 3C00 l SHDSL ports l V800R01 l POTS ports 5C00 l ISDN ports Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 857 V800R015C The MA5611S DE16 applies to FTTB and FTTC scenarios. MA5611S- VDSL2 ports (Supports vectoring) V800R015C The MA5611S DE48 (900- applies to FTTB and FTTC impedance) scenarios. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 858: Principle Of Fttb And Fttc Data Plan

    QoS, services, and security. The examples in this topic are based on these principles to plan data. 11.2.1 Principle of Device Management Data Plan The device management plan includes channel management plan and the IP address plan. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 859 HGW functions as a DHCP client, obtains a public network IP address using DHCP, and connects to the TR069 server (ACS). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 860: Principle Of Qos Data Plan

    The assured bandwidth is the maximum bandwidth required by management packets, VoIP, and IPTV upstream packets. The maximum bandwidth is larger than or equal to the maximum bandwidth that users apply. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 861 (in the case of multi STBs access). The upstream bandwidth is mainly used for Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 862: Principle Of Internet Access Service Data Plan

    ONUs under the same S-VLAN + C-VLAN PON board do not have the same C- VLAN. FTTB/FTTC+HGW HGWs (LAN networking (ONU upstream providing the VoIP transmission) service) Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 863 It is recommended that you use stacking VLANs as S-VLANs so that security features, such as PPPoE+/option 82, and anti-MAC attack, and anti-MAC spoofing can be easily deployed. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 864 HGWs: MDUs translate user VLANs to C-VLANs (user VLAN <-> C-VLAN) and add S-VLANs to packets. Ensure that the C-VLANs of users using the same S- VLAN do not repeat each other. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 865: Optional) Principle Of Vectoring Data Plan

    11.2.4 (Optional) Principle of Vectoring Data Plan Vectoring data plan includes grouping, the policy for activating a legacy customer premises equipment (CPE), and line profile planning of a port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 866 This activation policy is generally used in the mature stage of Vectoring applications. In this stage, the Vectoring performance is concerned and unnecessary crosstalk is better to be masked. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 867: Principle Of Voip Service Data Plan

    VLANs, the ONU VLAN+C- VLAN+C- VLANs are translates user VLAN) VLAN. planned. VLANs to C- VLANs. HGWs (xDSL upstream transmission): ONUs translate PVCs to C'- VLANs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 868 Untagged upstream packets of HGWs: MDUs map C-VLANs based on user ports. User-VLAN-tagged upstream packets of HGWs: MDUs translate user VLANs to C-VLANs (user VLAN <-> C-VLAN). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 869 MGC or address IMS core network Default IP address Next hop IP address from an ONU/HGW to device.) of the MG an MGC/IMS MG interface/SIP interface ID - Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 870 (category 1 government users) l cat2: government2 (category 2 government users) l cat3: normal (common users). This is the default value. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 871: Principle Of Iptv Service Data Plan

    IPTV services. IPTV services include multicast service and VoD service. These two services have relationships and independence in VLAN planning. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 872 MVLANs. MVLANs unchanged. l Downstream multicast service flows: The ONU replicates multicast packets based on user ports multicasts downstream multicast packets across VLANs: user VLAN <-> MVLAN Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 873 VLANs, the translates user VLANs to C-VLANs. l When packets are sent from the HGW using xDSL upstream transmission, the ONU translates PVCs to C- VLANs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 874 The MDU The OLT replicates replicates multicast multicast packets based packets based on user ports on GE ports with multicasts MVLANs downstream unchanged. packets among MVLANs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 875 HGWs: MDUs map C-VLANs based on user ports. User- VLAN- tagged upstream packets of HGWs: MDUs translate user VLANs to C- VLANs (user VLAN <-> C- VLAN). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 876 Ethernet on user ports, extending boards, and multicasts the the Ethernet packets extending among boards MVLANs replicate (user VLAN multicast <- MVLAN). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 877 C-VLANs based on user ports. User- VLAN- tagged upstream packets of HGWs: The extended subrack translates user VLANs to C-VLANs (user VLAN <-> C- VLAN). Note Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 878 Multicast preview profile Default Multicast fast leave Enabling this function is recommended. It reduced the exchange of IGMP packets, saving the bandwidth resources. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 879: Principle Of Security Data Plan

    IP address is the IP address of the device, and therefore the system is protected. Use this solution for new site deployment. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 880 After anti-IP spoofing is enabled, the function for MDU. system can prevent users from forging IP addresses to perform malicious attacks. Use this solution for new site deployment. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 881: Configuring Services In Various Fttb And Fttc Scenarios (Gpon And 10G Gpon Access)

    Scenarios (GPON and 10G GPON Access) This topic describes how to configure the Internet access service, voice service and multicast service in GPON/10G GPON access mode in FTTB/FTTC networking scenarios. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 882: Fttb Networking (Lan Access Without Hgw)

    LAN access. LAN access is easily and commonly deployed and therefore becomes the first choice for bandwidth construction. Service Requirements Only Internet access service and VoIP service are supported and there is no multicast requirement. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 883: Configuration Procedure

    Phone splitter Internet PE-AGG Phone 11.3.1.2 Configuration Procedure Figure 11-4 shows the configuration roadmap diagram in the FTTB and FTTC networking scenarios using LAN access without HGWs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 884 HGWs. Therefore, you need to ONU. channel. create an Internet access service channel and a VoIP service channel on the OLT. l Configure the VoIP service channel. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 885: Adding An Onu To An Olt

    When an ONU is added, corresponding profiles need to be bound to the ONU, including the dynamic bandwidth allocation (DBA) profile, line profile, and alarm profile. For details about functions and configuration methods for these profiles, see Table 11-5. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 886 ONU. Data plan Table 11-6 Data plan Item Data DBA profile Profile name: fttb_dba Profile type: type3 Assured bandwidth: 8 Mbit/s Maximum bandwidth: 20 Mbit/s Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 887 ONT ID: 1 Procedure Step 1 Configure GPON ONU profiles. Configure a DBA profile. huawei(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 20480 Configure an ONU line profile. Add GPON ONU line profile 10 fttb(c). huawei(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c)
  • Page 888 There are two modes to add an ONT: add an ONT offline and confirm an automatically discovered ONU. Add an ONU offline. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c) Confirm an automatically discovered ONU. huawei(config)#interface gpon 0/2...

  • Page 889: Configuring The Management Channel Between The Olt And The Onu

    Configure the inband management VLAN to 8, VLAN priority to 6, and the IP address to 192.168.50.1/24. huawei(config)#vlan 8 smart huawei(config)#port vlan 8 0/19 0 huawei(config)#vlan priority 8 6 huawei(config)#interface vlanif 8 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 890: Configuring The Service Channel Between The Olt And The Onu

    11, and user-side VLAN ID to 8. The OLT does not limit inband management service flows. Therefore, it is recommended that you use default traffic profile 6. huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6 Step 4 Confirm that the management channel between the OLT and the ONU is available.
  • Page 891 ID of the OLT is the same as the upstream VLAN ID of the ONU, that is, 1001. The Internet access service uses GEM port 12. – For the ONU: The upstream VLAN ID is 1001. huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 12 multi- service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright ©...

  • Page 892: Configuring Lan Internet Access Service (On The Onu)

    VLAN ID of the ONU, that is, 200. The VoIP service uses GEM port 13. – For the ONU: The upstream VLAN ID is 200. huawei(config)#service-port 201 vlan 200 gpon 0/2/1 ont 1 gemport 13 multi- service user-vlan 200 rx-cttr 9 tx-cttr 9 ----End 11.3.1.6 Configuring LAN Internet Access Service (On the ONU)
  • Page 893 Assume that the committed information rate (CIR) is 4 Mbit/s, priority of upstream packets is 0, and downstream packets are scheduled based on the priorities specified in the traffic profile. Configure traffic profile 8. huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- Setting Step 5 Add a service port.

  • Page 894: Configuring H.248 Voice Service (On The Onu)

    This example creates one service port as an example. Each service port maps a user. When configuring another service port, map the corresponding SVLAN. huawei(config)#service-port 101 vlan 1001 eth 0/3/1 multi-service user-vlan untagged rx-cttr 8 tx-cttr 8 Step 6 Save the data.
  • Page 895 IP addresses of the Layer 3 interface. These IP addresses are the sources of the IP address pools for the media stream and the signaling flows. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 896 V3. huawei(config-if-h248-0)#if-h248 attribute mgip 10.10.10.10 mgport 2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-port 2944 mg-media-ip1 10.10.10.10 start-negotiate-version 1 Step 7 Reset the MG interface. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 897: Configuring Sip Voice Service (On The Onu)

    MG interface does not support terminal layering, the terminal identification is mandatory. The terminal identification must be unique on one MG interface. huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001 Step 9 Configure the call priority of a PSTN user.
  • Page 898 5060 IP address of the main IMS 200.200.200.200/24 equipment Port ID of the main IMS 5060 equipment Coding scheme Text Transmission mode Home domain name (SIP) huawei Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 899 Set the media IP address and signaling IP address to 10.10.10.10, and the media gateway to 10.10.10.1. huawei(config)#voip huawei(config-voip)#ip address media 10.10.10.10 10.10.10.1 huawei(config-voip)#ip address signaling 10.10.10.10 huawei(config-voip)#quit Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 900 To configure the data of multiple SIP PSTN users in batches, run the sippstnuser batadd command. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/23 0 telno 83110001 Step 10 Configure call priorities for SIP PSTN users. huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 huawei(config-esl-user)#quit Step 11 Configure all the PSTN ports to support polarity reversal.

  • Page 901: Configuring Link Aggregation, Congestion Control, And Security Policies

    QoS planning principles, see 11.2.2 Principle of QoS Data Plan. huawei(config)#queue-scheduler strict-priority huawei(config)#cos-queue-map cos0 0 cos4 4 cos5 5 cos6 6 Configure system security. – Enable deny of service (DoS) anti-attack on both the OLT and optical network units (ONUs).
  • Page 902 – Enable Dynamic Host Configuration Protocol (DHCP) Option 82 on both the OLT and ONUs. This configuration is recommended for the DHCP-based Internet access service. Enable DHCP Option 82 on both the OLT and ONUs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 903 PITP at the port level. – The VLAN level: In global config mode, run the vlan service-profile command to create a VLAN service profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 904: Verifying Services

    The user name, password, and BRAS. authentication mode must be configured on the BRAS before the PPPoE dialup emulation starts. An ONU supports a maximum of one PPPoE dialup emulation. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 905 User Name(length<1,65>):user0 User Password(length<0,16>):******* Authentication Mode: 1. Chap 2. Pap [default 1]:1 Overtime Time(5-60s)[default 5]:10 Query the emulation test information by running the display pppoe simulate info command. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 906: Fttb/C Networking (Xdsl Access, Without Hgw)

    The FTTB/C application scenario only supports Internet access and voice services without multicast demands. To reuse the existing phone lines and overcome the challenges caused by long distance between ONUs and subscribers, FTTB/C with xDSL access is recommended. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 907: Configuration Procedure

    Figure 11-5 FTTB/C networking diagram (xDSL) 11.3.2.2 Configuration Procedure Figure 11-6 shows the configuration roadmap diagram in the FTTB and FTTC networking scenarios using xDSL access without HGWs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 908 HGWs. Therefore, you need to ONU. channel. create an Internet access service channel and a VoIP service channel on the OLT. l Configure the VoIP service channel. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 909: Adding An Onu To An Olt

    When an ONU is added, corresponding profiles need to be bound to the ONU, including the dynamic bandwidth allocation (DBA) profile, line profile, and alarm profile. For details about functions and configuration methods for these profiles, see Table 11-8. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 910 ONU. Data plan Table 11-9 Data plan Item Data DBA profile Profile name: fttb_dba Profile type: type3 Assured bandwidth: 8 Mbit/s Maximum bandwidth: 20 Mbit/s Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 911 ONT ID: 1 Procedure Step 1 Configure GPON ONU profiles. Configure a DBA profile. huawei(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 20480 Configure an ONU line profile. Add GPON ONU line profile 10 fttb(c). huawei(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c)
  • Page 912 There are two modes to add an ONT: add an ONT offline and confirm an automatically discovered ONU. Add an ONU offline. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c) Confirm an automatically discovered ONU. huawei(config)#interface gpon 0/2...

  • Page 913: Configuring The Management Channel Between The Olt And The Onu

    Configure the inband management VLAN to 8, VLAN priority to 6, and the IP address to 192.168.50.1/24. huawei(config)#vlan 8 smart huawei(config)#port vlan 8 0/19 0 huawei(config)#vlan priority 8 6 huawei(config)#interface vlanif 8 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 914: Configuring The Service Channel Between The Olt And The Onu

    11, and user-side VLAN ID to 8. The OLT does not limit inband management service flows. Therefore, it is recommended that you use default traffic profile 6. huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6 Step 4 Confirm that the management channel between the OLT and the ONU is available.
  • Page 915 ID of the OLT is the same as the upstream VLAN ID of the ONU, that is, 1001. The Internet access service uses GEM port 12. – For the ONU: The upstream VLAN ID is 1001. huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 12 multi- service Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright ©...

  • Page 916: Configuring The Internet Access Service (Adsl2+ Access, On The Onu)

    VLAN ID of the ONU, that is, 200. The VoIP service uses GEM port 13. – For the ONU: The upstream VLAN ID is 200. huawei(config)#service-port 201 vlan 200 gpon 0/2/1 ont 1 gemport 13 multi- service user-vlan 200 rx-cttr 9 tx-cttr 9 ----End 11.3.2.6 Configuring the Internet Access Service (ADSL2+ Access, on the ONU)
  • Page 917 CIR: 4 Mbit/s VLAN priority: 0 Downstream priority policy: local-setting VPI/VCI of VPI: 0 Internet service providers (ISPs) provide VPI/ ADSL2+ VCI information. VCI: 35 users Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 918 Add traffic profile 8 and set the committed information rate (CIR) to 4 Mbit/s. The priority for upstream packets is 0, and downstream packets are scheduled based on the priority specified in the traffic profile. huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- setting Step 3 Create service VLANs.

  • Page 919: Configuring The Internet Access Service (Vdsl2 Access, On The Onu)

    To add: vdsl line-profile add or transmission mode, adaptation mode of vdsl line-profile quickadd upstream/downstream transmit rates, signal-to-noise ratio (SNR) margin, upstream power back-off (UPBO), and downstream power back-off (DPBO). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 920 Coding violations counts (CVC) profile add or vdsl channel-alarm- profile quickadd l Corrected blocks counts (CBC) Data Plan Table 11-13 provides key information about the Internet access service (VDSL2 access). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 921 Add traffic profile 8 and set the committed information rate (CIR) to 4 Mbit/s. The priority for upstream packets is 0, and downstream packets are scheduled based on the priority specified in the traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 922: Optional) Configuring Vectoring

    Access Module Commissioning and Configuration Guide 11 FTTB and FTTC Solution Configuration huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- setting Step 3 Create service VLANs. Create service VLANs 1001-1016 in batches whose type is smart and attribute is common (the service VLAN IDs must be consistent with the user VLAN IDs of the OLT).
  • Page 923 NOTE Services in a vectoring group port are interrupted when the vectoring function is enabled or disabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 924 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 925 This mode is used in Vectoring medium phase when some CPEs have not been upgrade or replaced. l force-friendly-ds- limit-us: force friendly is used in the downstream Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 926 For MA5603T, when configuring vectoring, learn configuration item functions and configuration methods beforehand by referring to Table 11-15. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 927 VP boards. l Before enabling vectoring, globally configure the band plan. NOTE Services in a vectoring group port are interrupted when the vectoring function is enabled or disabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 928 Vectoring tasks caused by frequent online and offline on a port, set the policy for controlling frequent online and offline on ports based on site requirements. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 929 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 930 This mode is used in Vectoring medium phase when some CPEs have not been upgrade or replaced. l force-friendly-ds- limit-us: force friendly is used in the downstream Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 931 Policy for activating a no-limit The policy for activating a legacy customer vectoring legacy CPE is premises equipment configured as no-limit at the (CPE) initial stage of vectoring application. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 932 Log in to the ONU remotely and start the configuration. By default, the user name is root and the password is mduadmin. Globally configure the band plan type. huawei(config)#xdsl vectoring bandplan-type 998ade us0-type type-a Configure the policy for activating a vectoring legacy CPE. huawei(config)#xdsl vectoring legacy-cpe activate-policy no-limit Configure the policy for controlling frequent online and offline on ports.

  • Page 933: Configuring H.248 Voice Service (On The Onu)

    By default, the user name is root and the password is admin. Globally configure the band plan type. huawei(config)#xdsl vectoring bandplan-type 998ade us0-type type-a Configure the vectoring profile as huawei and bind it to the VDSL2 port in the vectoring group. huawei(config)#xdsl vectoring-profile add control enable enable name...
  • Page 934 Cat3 for phone 2 to phone 24 (default) User type Common user (DEL user by default) Common System parameter Default value parameter Overseas parameter Default value PSTN port attribute Polarity-reversal Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 935 MGC are in different network segments, you need to configure a route for the network segment from gateway 10.10.10.1 to 200.200.200.0. huawei(config)#ip route-static 200.200.200.0 24 10.10.10.1 Step 5 Add an MG interface. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 936 MG interface does not support terminal layering, the terminal identification is mandatory. The terminal identification must be unique on one MG interface. huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001 Step 9 Configure the call priority of a PSTN user.

  • Page 937: Configuring Sip Voice Service (On The Onu)

    Media and 0/0/1 paramet (It must be signaling upstream the same as port that on the IMS core Media IP address 10.10.10.10/24 network device.) and signaling IP address Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 938 Create an upstream VLAN. The VLAN ID is 200 and the VLAN is a smart VLAN. huawei(config)#vlan 200 smart Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 939 0 Are you sure to add the SIP interface?(y/n)[n]:y Step 6 Configure the basic attributes of the SIP interface. huawei(config-if-sip-0)#if-sip attribute basic media-ip 10.10.10.10 signal-ip 10.10.10.10 signal-port 5060 transfer udp primary-proxy-ip1 200.200.200.200 primary-proxy-port 5060 home-domain huawei sipprofile-index 1 Step 7 (Optional) Configure the optional attributes of the SIP interface.

  • Page 940: Configuring Link Aggregation, Congestion Control, And Security Policy

    To configure the data of multiple SIP PSTN users in batches, run the sippstnuser batadd command. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/23 0 telno 83110001 Step 10 Configure call priorities for SIP PSTN users. huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 huawei(config-esl-user)#quit Step 11 Configure all the PSTN ports to support polarity reversal.
  • Page 941 QoS planning principles, see 11.2.2 Principle of QoS Data Plan. huawei(config)#queue-scheduler strict-priority huawei(config)#cos-queue-map cos0 0 cos4 4 cos5 5 cos6 6 Configure system security. – Enable deny of service (DoS) anti-attack on both the OLT and optical network units (ONUs).
  • Page 942 – Enable Policy Information Transfer Protocol (PITP) on both the OLT and ONUs. This configuration is recommended for the PPPoE-based Internet access service. Enable PITP on both the OLT and ONUs. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 943: Verifying Services

    Remote site verification eliminates the need to go to site for a second time. Prerequisites ONUs are properly connected to upper-layer devices. The broadband remote access server (BRAS) and media gateway controller (MGC)/IP Multimedia Subsystem (IMS) have been configured. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 944 Called port: 0/3/23 parameter emulation test, retain the parameter Called number: 83110024 settings as default. To query default values, run the display pots emulational configuration command. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 945: Fttb/Fttc+Hgw Networking (Voice Service Provided By Onu)

    The services are sent upstream to the optical network unit (ONU) over a local area network (LAN) or x digital subscriber line (xDSL). The Integrated Access Device (IAD) in the ONU provides voice services. 11.3.3.1 Service Requirements and Application Scenario Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 946 The ONUs used in this application scenario include MA5822, MA5616, MA5622A, MA5603T, MA5612. LAN ports are available on MA5616, MA5822, MA5612. xDSL ports are available on MA5616, MA5622A, MA5603T. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 947: Configuration Procedure

    Internet PE-AGG xDSL+ POTS Splitter Phone Phone 11.3.3.2 Configuration Procedure Figure 11-8 shows the configuration roadmap diagram in the FTTB+HGW networking scenarios (ONU providing the VoIP service). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 948 OLT and the between the OLT and the ONU is ONU. configured and available, you can log in to the ONU from the OLT to configure the ONU. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 949 VoIP service. Only one of them VoIP service on is configured at a time. the ONU. Configure the SIP-based VoIP service on the ONU. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 950: Adding An Onu To An Olt

    When an ONU is added, corresponding profiles need to be bound to the ONU, including the dynamic bandwidth allocation (DBA) profile, line profile, and alarm profile. For details about functions and configuration methods for these profiles, see Table 11-17. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 951 ONU. Data plan Table 11-18 Data plan Item Data DBA profile Profile name: fttb_dba Profile type: type3 Assured bandwidth: 8 Mbit/s Maximum bandwidth: 20 Mbit/s Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 952 ONT ID: 1 Procedure Step 1 Configure GPON ONU profiles. Configure a DBA profile. huawei(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 20480 Configure an ONU line profile. Add GPON ONU line profile 10 fttb(c). huawei(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c)
  • Page 953 There are two modes to add an ONT: add an ONT offline and confirm an automatically discovered ONU. Add an ONU offline. huawei(config)#interface gpon 0/2 huawei(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c) Confirm an automatically discovered ONU. huawei(config)#interface gpon 0/2...

  • Page 954: Configuring The Management Channel Between The Olt And The Onu

    Configure the inband management VLAN to 8, VLAN priority to 6, and the IP address to 192.168.50.1/24. huawei(config)#vlan 8 smart huawei(config)#port vlan 8 0/19 0 huawei(config)#vlan priority 8 6 huawei(config)#interface vlanif 8 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 955: Configuring Service Channels Between An Olt And An Onu

    11, and user-side VLAN ID to 8. The OLT does not limit inband management service flows. Therefore, it is recommended that you use default traffic profile 6. huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6 Step 4 Confirm that the management channel between the OLT and the ONU is available.
  • Page 956 C-VLANs in the preceding table are defined for OLTs. That is, they are upstream VLANs or S-VLANs of ONUs. Procedure Configure a channel for the Internet access service. Create an S-VLAN and add an upstream port to it. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 957 ONU but not on the OLT, and traffic profile 6 is referenced. huawei(config)#service-port vlan 100 gpon 0/2/1 ont 1 gemport 12 multi- service user-vlan 1001 tag-transform translate-and-add rx-cttr 6 tx-cttr 6 Configure a channel for the VoIP service.
  • Page 958 Add traffic profile 10 and set priority-policy to local-setting. Then, traffic is scheduled based on the priority specified in the traffic profile. huawei(config)#traffic table ip index 10 cir off priority 4 priority- policy local-Setting Configure a service flow for the VoD service.

  • Page 959: Configuring The Internet Access Service (Lan Access, On The Onu)

    Configure a program library. Set the multicast IP address range to 224.1.1.10-224.1.1.100 and the IP address of the multicast server to 10.10.10.10. huawei(config-mvlan1000)#igmp program add batch ip 224.1.1.10 to-ip 224.1.1.100 sourceip 10.10.10.10 ----End 11.3.3.6 Configuring the Internet Access Service (LAN Access, on the ONU)

  • Page 960: Configuring The Internet Access Service (Adsl2+ Access, On The Onu)

    Access Module Commissioning and Configuration Guide 11 FTTB and FTTC Solution Configuration huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- setting Step 3 Create service VLANs. Create service VLANs 1001-1016 in batches whose type is smart and attribute is common (the service VLAN IDs must be consistent with the user VLAN IDs of the OLT).
  • Page 961 CIR: 4 Mbit/s VLAN priority: 0 Downstream priority policy: local-setting VPI/VCI of VPI: 0 Internet service providers (ISPs) provide VPI/ ADSL2+ VCI information. VCI: 35 users Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 962 Add traffic profile 8 and set the committed information rate (CIR) to 4 Mbit/s. The priority for upstream packets is 0, and downstream packets are scheduled based on the priority specified in the traffic profile. huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- setting Step 3 Create service VLANs.

  • Page 963: Configuring The Internet Access Service (Vdsl2 Access, On The Onu)

    To add: vdsl line-profile add or transmission mode, adaptation mode of vdsl line-profile quickadd upstream/downstream transmit rates, signal-to-noise ratio (SNR) margin, upstream power back-off (UPBO), and downstream power back-off (DPBO). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 964 Coding violations counts (CVC) profile add or vdsl channel-alarm- profile quickadd l Corrected blocks counts (CBC) Data Plan Table 11-21 provides key information about the Internet access service (VDSL2 access). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 965 Add traffic profile 8 and set the committed information rate (CIR) to 4 Mbit/s. The priority for upstream packets is 0, and downstream packets are scheduled based on the priority specified in the traffic profile. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 966: Optional) Configuring Vectoring

    Access Module Commissioning and Configuration Guide 11 FTTB and FTTC Solution Configuration huawei(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local- setting Step 3 Create service VLANs. Create service VLANs 1001-1016 in batches whose type is smart and attribute is common (the service VLAN IDs must be consistent with the user VLAN IDs of the OLT).
  • Page 967 NOTE Services in a vectoring group port are interrupted when the vectoring function is enabled or disabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 968 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 969 This mode is used in Vectoring medium phase when some CPEs have not been upgrade or replaced. l force-friendly-ds- limit-us: force friendly is used in the downstream Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 970 For MA5603T, when configuring vectoring, learn configuration item functions and configuration methods beforehand by referring to Table 11-23. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 971 VP boards. l Before enabling vectoring, globally configure the band plan. NOTE Services in a vectoring group port are interrupted when the vectoring function is enabled or disabled. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 972 Vectoring tasks caused by frequent online and offline on a port, set the policy for controlling frequent online and offline on ports based on site requirements. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 973 Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 974 This mode is used in Vectoring medium phase when some CPEs have not been upgrade or replaced. l force-friendly-ds- limit-us: force friendly is used in the downstream Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 975 Policy for activating a no-limit The policy for activating a legacy customer vectoring legacy CPE is premises equipment configured as no-limit at the (CPE) initial stage of vectoring application. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 976 Log in to the ONU remotely and start the configuration. By default, the user name is root and the password is mduadmin. Globally configure the band plan type. huawei(config)#xdsl vectoring bandplan-type 998ade us0-type type-a Configure the policy for activating a vectoring legacy CPE. huawei(config)#xdsl vectoring legacy-cpe activate-policy no-limit Configure the policy for controlling frequent online and offline on ports.

  • Page 977: Configuring H.248 Voice Service (On The Onu)

    By default, the user name is root and the password is admin. Globally configure the band plan type. huawei(config)#xdsl vectoring bandplan-type 998ade us0-type type-a Configure the vectoring profile as huawei and bind it to the VDSL2 port in the vectoring group. huawei(config)#xdsl vectoring-profile add control enable enable name...
  • Page 978 Cat3 for phone 2 to phone 24 (default) User type Common user (DEL user by default) Common System parameter Default value parameter Overseas parameter Default value PSTN port attribute Polarity-reversal Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 979 MGC are in different network segments, you need to configure a route for the network segment from gateway 10.10.10.1 to 200.200.200.0. huawei(config)#ip route-static 200.200.200.0 24 10.10.10.1 Step 5 Add an MG interface. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 980 MG interface does not support terminal layering, the terminal identification is mandatory. The terminal identification must be unique on one MG interface. huawei(config)#esl user huawei(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001 Step 9 Configure the call priority of a PSTN user.

  • Page 981: Configuring Sip Voice Service (On The Onu)

    Media and 0/0/1 paramet (It must be signaling upstream the same as port that on the IMS core Media IP address 10.10.10.10/24 network device.) and signaling IP address Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 982 Create an upstream VLAN. The VLAN ID is 200 and the VLAN is a smart VLAN. huawei(config)#vlan 200 smart Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 983 0 Are you sure to add the SIP interface?(y/n)[n]:y Step 6 Configure the basic attributes of the SIP interface. huawei(config-if-sip-0)#if-sip attribute basic media-ip 10.10.10.10 signal-ip 10.10.10.10 signal-port 5060 transfer udp primary-proxy-ip1 200.200.200.200 primary-proxy-port 5060 home-domain huawei sipprofile-index 1 Step 7 (Optional) Configure the optional attributes of the SIP interface.

  • Page 984: Configuring The Iptv Service (On The Onu)

    To configure the data of multiple SIP PSTN users in batches, run the sippstnuser batadd command. huawei(config)#esl user huawei(config-esl-user)#sippstnuser batadd 0/3/0 0/3/23 0 telno 83110001 Step 10 Configure call priorities for SIP PSTN users. huawei(config-esl-user)#sippstnuser attribute set 0/3/0 priority cat2 huawei(config-esl-user)#quit Step 11 Configure all the PSTN ports to support polarity reversal.
  • Page 985 In this example, the query result shows that no traffic profile meets the requirements, so a traffic profile needs to be configured. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 986 Assume that the VPI/VCI is 0/35 and the ADSL2+ port is 0/2/0. Add a service flow as follows: huawei(config)#service-port 301 vlan 300 adsl vpi 0 vci 35 0/2/0 multi- service user-vlan untagged rx-cttr 10 tx-cttr 10 – If HGWs are connected to an ONU upstream in VDSL2 mode, formats of upstream packets depend on the encapsulation mode.

  • Page 987: Configuring Link Aggregation, Congestion Control, And Security Policy

    – If HGWs are connected to an ONU upstream in ADSL2+ mode, assume that the VPI/ VCI is 0/35 and the ADSL2+ port is 0/2/0, and add a service flow as follows: huawei(config)#service-port 401 vlan 1000 adsl vpi 0 vci 35 0/2/0 multi- service user-vlan untagged rx-cttr 10 tx-cttr 10 –...
  • Page 988 QoS planning principles, see 11.2.2 Principle of QoS Data Plan. huawei(config)#queue-scheduler strict-priority huawei(config)#cos-queue-map cos0 0 cos4 4 cos5 5 cos6 6 Configure system security. – Enable deny of service (DoS) anti-attack on both the OLT and optical network units (ONUs).
  • Page 989 VLAN. – The service port level: In global config mode, run the dhcp option82 service- port command to enable DHCP Option 82 at the service port level. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 990: Configuring The Internet Access Service (On The Hgw)

    This topic describes how to configure the Internet access service on an HG239 that is connected to an ONU upstream through a LAN and on an HG527 that is connected to an ONU upstream in ADSL2+ mode. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 991 Set parameters for the Internet access service. Assume that ports LAN1 and LAN2 are Internet access ports for PCs. Choose Network > Bandwidth Configuration from the navigation tree. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 992: Configuring The Iptv Service (On The Hgw)

    (the Internet service provider (ISP) provides the default user name and default password). Then, click OK. Configure multicast parameters. This example assumes LAN 4 as an IPTV port. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 993 Set the parameters as follows: Parameter Value Bearing OTHER: The connection is used for the IPTV service. service Enabling The LAN connection is enabled when this check box is selected. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 994: Verifying Services

    ONUs and upper-layer devices have been connected properly. The BRAS and MGC/IMS have been configured. Background Information The following table lists the remote verification methods for different services. NOTE Currently, the VoD service does not support remote verification. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 995 Service flow ID: 101 The entered user name, password, and dialup authentication mode must be Emulation timeout time: 10s emulation consistent with those configured on parameter the BRAS. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 996 The ONU outputs the call emulation result after the test is complete. The ONU outputs the call emulation result and failure of the cause if the emulation test fails. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 997 Run the igmp static-join command to order a multicast program by emulating a multicast user. huawei(config)#btv huawei(config-btv)#igmp static-join service-port 401 ip 224.1.1.10 vlan 1000 Run the display igmp use command to query the status of the multicast user. huawei(config-btv)#display igmp user service-port 401 User : 0/3/1 //*Use an ETH port as an example.

  • Page 998: Fttb/Fttc+Hgw Networking (Hgw Providing The Voip Service)

    GPON FTTB+HGW network. The GPON OLT is deployed at the central office and connects to the MAN using aggregation, and the ONU is deployed in the buildings Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

  • Page 999: Configuration Procedure

    Headend Laptop Splitter Internet PE-AGG xDSL Phone 11.3.4.2 Configuration Procedure Figure 11-10 shows the configuration roadmap diagram in the FTTB+HGW networking scenarios (HGW providing the VoIP service). Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 1000 OLT and the between the OLT and the ONU is ONU. configured and available, you can log in to the ONU from the OLT to configure the ONU. Issue 01 (2014-04-30) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

This manual is also suitable for:

Smartax ma5600tSmartax ma5608t

Table of Contents