Connecting The Ducts - joule HEATBANK Operating And Installation Manual

Installation and user manual
Installation and user manual
installaton guide
3.2 CONNECTING THE CONDENSATE HOSE
Damage to the appliance! Connect the condensate hose to the con-
3.2 CONNECTING THE CONDENSATE HOSE
3.2 CONNECTING THE CONDENSATE HOSE
densate drain before installing the part .
• Do not bend the condensate hose!
Damage to the appliance! Connect the condensate hose to the
Damage to the appliance! Connect the condensate hose to the
condensate drain before installing the part.
condensate drain before installing the part.
The condensate is drained on the rear side of the appliance, see figure 4.
• Do not bend the condensate hose!
•
Do not bend the condensate hose!
• Connect the condensate hose to the condensate drain (1)
The condensate is drained on the rear side of the appliance,
The condensate is drained on the rear side of the appliance,
• Connect the condensate hose to the collection area.
see figure 4.
see figure 4.
• Drain off condensate via a siphon drain (2)
• Connect the condensate hose to the condensate drain (1)
•
Connect the condensate hose to the condensate drain (1)
Don't disconnect the condensate hose from the condensate drain, this
• Connect the condensate hose to the collection area.
•
Connect the condensate hose to the collection area.
will damage the connection in the foam!
• Drain off condensate via a siphon drain (2)
•
Drain off condensate via a siphon drain (2)
Don't disconnect the condensate hose from the condensate drain,

3.3 CONNECTING THE DUCTS

Don't disconnect the condensate hose from the condensate drain,
this will damage the connection in the foam!
this will damage the connection in the foam!
The air inlet can be located in the installation room, in a different room
3.3 CONNECTING THE DUCTS
3.3 CONNECTING THE DUCTS
or outside . In the latter two cases, air inlet ducts must be installed . If
ducts are used select "ducts on". (see 4.8.5)
The air inlet can be located in the installation room, in a different room or outside. In the latter two cases, air inlet
The air inlet can be located in the installation room, in a different room or outside. In the latter two cases, air inlet
ducts must be installed. If ducts are used select "ducts on". (see 4.8.5)
ducts must be installed. If ducts are used select "ducts on". (see 4.8.5)
To ensure maximum appliance performance and to prevent condensa-
tion forming on the external duct walls, use thermally and acoustically
To ensure maximum appliance performance and to prevent condensation forming on the external duct walls, use
To ensure maximum appliance performance and to prevent condensation forming on the external duct walls, use
insulated ducts .
thermally and acoustically insulated ducts.
thermally and acoustically insulated ducts.
When choosing a room for the air inlet, observe the average air tem-
When choosing a room for the air inlet, observe the average air temperature and required air flow rate. In order to
When choosing a room for the air inlet, observe the average air temperature and required air flow rate. In order to
perature and required air flow rate. In order to minimize air resistance,
minimize air resistance, lay the air inlet and outlet ducts (Ø 160 mm) as straight as possible.
minimize air resistance, lay the air inlet and outlet ducts (Ø 160 mm) as straight as possible.
lay the air inlet and outlet ducts (Ø 160 mm) as straight as possible.
The length (Leq) of the air inlet and outlet ducts must not exceed the following values:
The length (Leq) of the air inlet and outlet ducts must not exceed the following values:
The length (Leq) of the air inlet and outlet ducts must not exceed the
following values:
• 30m at fan speed 1 (SP1)
• 30m at fan speed 1 (SP1)
• 30m at fan speed 1 (SP1)
• 30m – 60m at fan speed 2 (SP2)
• 30m – 60m at fan speed 2 (SP2)
• 30m – 60m at fan speed 2 (SP2)
Description
0,5 m duct
0,5 m duct
0,5 m duct
1 m duct
1 m duct
1 m duct
2m duct
2m duct
2m duct
10 m hose
10 m hose
10 m hose
45° elbow
45° elbow
45° elbow
90° elbow
90° elbow
90° elbow
90° flexible curve
90° flexible curve
90° flexible curve
Weather grille
Weather grille
Weather grille
Roof output
Roof output
Roof output
To ensure that condensate forming in the air inlet and air outlet
To ensure that condensate forming in the air inlet and air outlet
ducts drains from the appliance:
To ensure that condensate forming in the air inlet and air outlet ducts
ducts drains from the appliance:
• Install air ducts at a slight angle to the air inlet and air outlet
drains from the appliance:
•
Install air ducts at a slight angle to the air inlet and air outlet
apertures on the top side of the appliance.
• Install air ducts at a slight angle to the air inlet and air outlet aper-
apertures on the top side of the appliance.
tures on the top side of the appliance .
Always use insulated pipes to prevent condensate at the air inlet
Always use insulated pipes to prevent condensate at the air inlet
and the air outlet. By the use of outside air condensate can occur.
Always use insulated pipes to prevent condensate at the air inlet and
and the air outlet. By the use of outside air condensate can occur.
the air outlet . By the use of outside air condensate can occur .
It's recommended to use SP2 if ducts are used with a high
It's recommended to use SP2 if ducts are used with a high
resistance. (To select SP2 see 4.8.4)
It's recommended to use SP2 if ducts are used with a high resistance .
resistance. (To select SP2 see 4.8.4)
(To select SP2 see 4.8.4)
Please note that a high ventilator volume results in a higher sound
Please note that a high ventilator volume results in a higher sound
level.
Please note that a high ventilator volume results in a higher sound
level.
level .
www.jouleuk.co.uk
14
14
Air inlet Air outlet
Air inlet Air outlet
Air inlet Air outlet
0,5 m
0,5 m
0,5 m
1,0 m
1,0 m
1,0 m
2,0 m
2,0 m
2,0 m
19,0 m
19,0 m
19,0 m
0,9 m
0,9 m
0,9 m
2,0 m
2,0 m
2,0 m
2,3 m
2,3 m
2,3 m
8 m 4 m
8 m 4 m
8 m 4 m
7 m 4 m
7 m 4 m
7 m 4 m
Fig. 4
Fig. 4
17