U.S. Products ADVANTAGE-400H Information & Operating Instructions
  1. Manuals
  2. Brands
  3. U.S. Products Manuals
  4. Floor Machine
  5. ADVANTAGE-400H Series
  6. Information & operating instructions

U.S. Products ADVANTAGE-400H Information & Operating Instructions

Extractor 120v
Hide thumbs Also See for ADVANTAGE-400H:
Table of Contents

Advertisement

Quick Links

ADVANTAGE-400H
EXTRACTOR
120V
INFORMATION
&
OPERATING
INSTRUCTIONS
CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ
ALL SECTIONS OF THIS INSTRUCTION MANUAL
IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.
2. Connect the machine to a properly grounded outlet, only.
3. Keep machine from rain and snow, extremes in temperatures, and store in a heated
location. Use the machine indoors. Do not use outdoors.
4. Use approved chemicals only. NO SOLVENTS.
5. Wear gloves or use rags when removing quick disconnects to prevent burns.
6. Never use water above 130º F/54º C in the solution tank.
2-15-2010
1

Advertisement

Table of Contents
loading

Related Manuals for U.S. Products ADVANTAGE-400H

Summary of Contents for U.S. Products ADVANTAGE-400H

  • Page 1 ADVANTAGE-400H EXTRACTOR 120V INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offi ces other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine.

  • Page 3: Cleaning Solutions

    INSPECTION: Carefully unpack and inspect your ADVANTAGE-400H for shipping damage. Each machine is tested and inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the carrier immediately if you notice damage to the box or to the machine or parts.

  • Page 4: Switch Plate

    SWITCH PLATE MODEL (1): This identifi es the model of your Advantage machine. VACUUM SWITCH (2): MODEL This push-button switch turns on the vacuum. The switch will illuminate when it is on. PUMP SWITCH (3): The pump switch will illuminate when it is activated, and it will turn on the pump. HEAT SWITCH (4): The heat switch will illuminate when it is activated and will turn on the heater.

  • Page 5: Setup And Operation

    SET-UP & OPERATION: 1. Inspect the machine, hoses, and cleaning tools for cleanliness and completeness. 2. Screw the lid on the recovery tank. Close the drain gate. 3. Fill the holding tank with clear water. NOTE: although this machine is designed to supply instant hot water, the addition of warm water to the solution tank would increase heater effi...

  • Page 7: Part List

    ADVANTAGE-400H PART LIST 120V ITEM PART No DESCRIPTION ITEM PART No DESCRIPTION Drain Gate Hose clamp 187B Gasket 207A Filter, pump inlet O-ring Nipple Nut, 1-1/2” 2175 Lid, Solution tank Hose Barb, vacuum inlet Chain, 8” 1074 Gasket TKC-6 Solution tank, white 2086A Lid with Ring, 6”...

  • Page 8: Troubleshooting

    ADVANTAGE 400 TROUBLE SHOOTING: IF THIS OCCURS CHECK THIS Solution tank is empty, or fi lter is plugged up. NO SPRAY Clogged spray tip. Pump not running. Valve on wand not operating. Solution hose not completely connected to hose or to machine. This pump motor runs on AC voltage, so it should start running as soon as you PUMP DOES NOT RUN turn on the switch.

Table of Contents