1. Manuals
  2. Brands
  3. U.S. Products Manuals
  4. Floor Machine
  5. KING COBRA 1200 PRO
  6. Operating instructions manual

U.S. Products KING COBRA 1200 PRO Operating Instructions Manual

100v
Hide thumbs Also See for KING COBRA 1200 PRO:
Table of Contents

Advertisement

Quick Links

KING COBRA
DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ
IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
1. DANGER: High spraying pressure may cause severe injury. Always wear safety
glasses. Keep hands & feet away from spray. Never direct the spray towards people or pets.
2. Never allow the spray to remain fixed in one spot.
3. Before each use, remove the spray tool from the hose, and check to make sure the spray
nozzle is securely tightened to the spray tool. A loose nozzle could fly off during use.
4. If a leak occurs at the hose, IMMEDIATELY turn the machine off. Replace hose before
restarting.
5. Always use a defoamer when foaming occurs to prevent vacuum motor damage.
6. Keep the machine from rain and snow, extremes in temperatures, and store it in a heated
location. Use the machine indoors. Do not use outdoors.
100V
ALL SECTIONS OF THE INSTRUCTIONS
1200 PRO
®
INFORMATION
OPERATING
INSTRUCTIONS
&
6.5.2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KING COBRA 1200 PRO and is the answer not in the manual?

Questions and answers

Related Manuals for U.S. Products KING COBRA 1200 PRO

Summary of Contents for U.S. Products KING COBRA 1200 PRO

  • Page 1 KING COBRA 1200 PRO ® 100V INFORMATION & OPERATING INSTRUCTIONS DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THE INSTRUCTIONS IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. DANGER: High spraying pressure may cause severe injury. Always wear safety glasses.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine.

  • Page 3: Cleaning Solutions

    U.S. Products “X-1500” is recommended. The vacuum motor, pump motors, and the pumps do not require any scheduled maintenance; however, the...

  • Page 4: Switch Plate

    DUMP PUMP SWITCH PLATE ON/OFF GREEN SWITCH LIGHT 1200 PSI PUMP (NO HEAT) 1200 P.S.I. HEAT 500 P.S.I. CIRCUIT LOCATOR LIGHT INDICATES TWO CIRCUITS. HEAT SELECT 1200 PSI 500 PSI HEAT PUMP or VACUUM PUMP LIGHT HEAT ON/OFF ON/OFF SELECTOR SWITCH SWITCH SWITCH...

  • Page 5: 1200 Psi High Pressure Washer

    OPERATION REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE 1200 PSI HIGH PRESSURE WASHER Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make sure the hoses are in good condition and the spray nozzle(s) is tight. 2.
  • Page 6 OPERATION OF THE 1200 PSI PUMP CONTINUED: Add defoamer to the recovery tank. 10. Your machine has two solution outputs. The solution output for the 1200 psi pump is a quick disconnect located just below the fill hole on the holding tank, on the front face of the machine (the 500 psi outlet is a quick disconnect on the end of a short length of hose, on the front of the base section of the machine).
  • Page 7 OPERATION OF THE 500 PSI PUMP and HEAT CONTINUED: 4. Select ‘HEAT” by moving the HEAT/HIGH PRESSURE switch (2) towards the thermometer symbol. NOTE: this switch is off when it is set to the middle position and neither the 1200 PSI pump nor the heater is selected.

  • Page 8: Chemical Supply

    USING THE AUTO-FILL AND/OR AUTO-DUMP FEATURES AUTO-FILL 1 Chemical Supply: • Place the container of concentrated chemical cleaner -- use a product with a pH between 6 and 9 to avoid premature pump wear (which would void the warranty) -- in the holder on top of the recovery tank. •...
  • Page 9 AUTO-DUMP Operation: Before each use: if necessary, unscrew the stainless steel filter at the bottom of the recovery tank and clean it. Also make sure the float in the recovery tank is clean. • Attach a 3/4” garden hose to the dump pump outlet fitting on the back of the base of the machine. Refer to illustration below •...
  • Page 10 55 56 to outlet 111A 135A KC-1200 PRO 100V 120V 11/2/2006...

  • Page 11: Part List

    KING COBRA-1200 PRO PART LIST 100 V ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION Locknut, 5/16” jam 2084A Wheel, 10” FP500 Hose, Chemical Pick-up, complete Washer, flat, 5/16” Axle cap 1199 Check valve & filter Wire tie, white,8”...

  • Page 12: Specifications

    KING COBRA 1200 PRO ® 100V SPECIFICATIONS: Rotomolded Body: Lifetime Warranty Vacuum: 7.2” 3-stage, 140” of water lift VAC Shutoff: Ball Float Pump: Positive displacement, fully adjustable 0-500 psi & Positive displacement, 1200 psi, 2.2 gpm Heat: 1500 Watts Capacity: 16 gallon solution tank;...

Table of Contents