General Safety Instructions - Axminster ATDP13B User Manual

Work Place/Environment/Installation
Mains Powered Machines/ Primary Precautions
These machines are supplied with a moulded 13 Amp. Plug
and 3 core power cable. Before using the machine inspect the
cable and the plug to make sure that neither are damaged. If
any damage is visible have the machine inspected/repaired
by a suitably qualified person. If it is necessary to replace the
plug, it is preferable to use an 'unbreakable' type that will resist
damage. Only use a 13 Amp plug, make sure the cable clamp
is tightened securely. Fuse at 13 Amp. If extension leads are to
be used, carry out the same safety checks on them, and ensure
that they are correctly rated to safely supply the current that
is required for your machine. It is also recommended that the
power supply outlet is the switched type, and that the supply is
switched off whilst plugging in, or unplugging the machine.
General Instructions for 230V Tools
Good Working Practices/Safety
The following suggestions will enable you to observe good
working practices, keep yourself and fellow workers safe and
maintain your tools and equipment in good working order.
WARNING! KEEP TOOLS AND EQUIPMENT
OUT OF THE REACH OF YOUNG CHILDREN!
Work Place/Environment
DO NOT use when or where it is liable to get wet. If the machine
is to be used outside and it starts to rain stop work and move it
inside. If machine has got wet; dry it off as soon as possible, with
a cloth or paper towel.
DO NOT use 230V a.c. powered machines anywhere within a
site area that is flooded or puddled, and do not trail extension
cables across wet areas.
KEEP the machine clean; it will enable you to more easily see
any damage that may have occurred.
CLEAN the machine with a damp soapy cloth if needs be, do
not use any solvents or cleaners, as these may cause damage to
any plastic parts or to the electrical components.
KEEP the work area as uncluttered as is practical, this includes
personnel as well as material.

General Safety Instructions

WARNING! UNDER NO CIRCUMSTANCES
SHOULD CHILDREN BE ALLOWED IN WORK
AREAS!
It is good practice to leave the machine unplugged until work
is about to commence, also make sure to unplug the machine
when it is not in use, or unattended. Always disconnect by
pulling on the plug body and not the cable.
Once you are ready to commence work, remove any tools used
in the setting operations (if any) and place safely out of the way.
Re-connect the machine. Carry out a final check e.g. check the
drill bit is securely tightened in the machine, check you have
the correct speed and function set, check that the power cable
will not 'snag' etc.
Make sure you are comfortable before you start work,
balanced, not reaching etc. If the work you are carrying out is
liable to generate flying grit, dust or chips, wear the appropriate
safety clothing, goggles, gloves, masks etc. If the work
operation appears to be excessively noisy, wear ear-defenders.
If you wear your hair in a long style, wearing a cap, safety
helmet, hairnet, even a sweatband, will minimise the possibility
of your hair being caught up in the rotating parts of the
machine. Likewise,consideration should be given to the
removal of rings and wristwatches, if these are liable to be a
'snag' hazard. Consideration should also be given to non-slip
footwear, etc.
DO NOT work with cutting or boring tools of any description
if you are tired, your attention is wandering or you are being
subjected to distraction. A deep cut, a lost fingertip or worse is
not worth it!
DO NOT use this machine within the designated safety areas of
flammable liquid stores or in areas where there may be volatile
gases. There are very expensive, very specialised machines for
working in these areas, THIS IS NOT ONE OF THEM.
CHECK that drills are the correct type and size, are undamaged
and are kept clean and sharp, this will maintain their operating
performance and lessen the loading on the machine. Above all,
OBSERVE.... make sure you know what is happening around
you, and USE YOUR COMMON SENSE.
5