Related Manuals for Axminster AC285PD
Summary of Contents for Axminster AC285PD
- Page 1 AC285PD Code 105105 AC315PD Code 105106 AC220RD Code 105107 AC680RD Code 105112 Pillar Drills User manual AC315PD AC285PD AC220RD AC680RD AT&M: 13/07/2018 BOOK REF: 105153...
-
Page 2: Eu Declaration Of Conformity
Exploded Diagrams/Lists 24-25-26-27-28-29-31 Wiring Diagram Notes 33-34-35 EU Declaration of Conformity Cert No: Drill Press EU Declaration of Conformity Axminster Tools & Machinery Ltd This machine complies with the following directives: Axminster Devon EX13 5PH UK axminster.co.uk 2006/42/EC EN 12717+A1:2009 2006/95/EC declares that the machinery described:- 06/42/EC - Annex I/05.2006... -
Page 3: What's Included
What’s Included Model Number AC285PD (ZQJ4113A) Model Number AC315PD (ZQJ4116Q) Quantity Item Part Quantity Item Part Small Bench Pillar Drill Medium Bench Pillar Drill Model Number AC680RD (ZQJ3116A) Model Number AC220RD (ZQJ3116) Quantity Item Part Quantity Item Part Bench Radial Drill... - Page 4 What’s Included...
- Page 5 What’s Included...
- Page 6 What’s Included...
- Page 7 General Safety Instructions for 230V Machines • Carry out a final check e.g. check the cutting tool The following will enable you to observe good working practices, keep yourself and fellow workers safe and maintain is securely tightened in the machine and the correct your tools and equipment in good working order.
-
Page 8: Specification
Specification Code 105105 Code 105106 Model AC285PD Model AC315PD Power 250W 50Hz (230V 1 ph) Power 375W 50Hz (230V 1 ph) Speed Range (5) 600 - 2,500rpm Speed Range (12) 210-2,580rpm Swing 210mm Swing 254mm Chuck Size 1.5-13mm Keyless Chuck Cap/Type... - Page 9 Having unpacked your machine and accessories, check the Fig 02 contents against the equipment list ”What’s Included” , if there are any discrepancies, please contact Axminster Tool Centre using the guide on our website. PLEASE DISPOSE OF THE PACKAGING RESPONSIBLY;...
- Page 10 Assembly collar over the column and slide it down onto the top of the rack. Lock it in place with the grub screw, ensuring that it has captured the upper end of the rack securely, but not too tight that the rack cannot be swivelled around the pillar see fig 8 . Fig 06-07 6.
- Page 11 Assembly Fig 17-18-19 Grub screw Note: On the two radial drills fit the extension arm (2d) into the mounting arm (2b and 2c) then the tables, see figs 14-15-16. Fig 15-16 Radial Pillar Drill Head Only 2. Lay the drill head on its side, locate the column spacer block and insert it into machined recess inside the base of the drill head, see fig 20.
- Page 12 3. Locate another lift and shift handle (10) and screw it into the threaded hole for the Horizontal clamp assembly, see fig 22. Fig 22 1-13mm Keyless Chuck AC285PD Only Locate the chuck (7) and insert up over the morse taper arbor, using a high faced mallet, lightly tap home.
- Page 13 30. Fig 29-30 Lever Feed Handles Locate the three lever feed handles (6) and screw them into the threaded holes on the depth stop ring, see fig 31-32. Fig 31-32 Model Letter AC285PD AC315PD AC220RD AC680RD...
-
Page 14: Illustration And Parts Description
Chuck guard Retaining collar Crank handle Keyless chuck Drill table Rise and fall rack Drill column Mounting flange Base casting ‘T’ slot Base casting 105105 AC285PD 105106 AC315PD Pillar drill securing holes Micro switch 105105 Drive Pulley 105106 Drive Pulley... - Page 15 Illustration and Parts Description Depth stop clamp (A) ON/OFF switch (A) Motor yoke clamp (A) Depth scale (B), Depth scale pointer (C) Emergency stop button (B) Table tilt locking bolt 90˚ Locking bolt Motor yoke clamp (A) Drive belt tensioning lever (B) Table tilt scale (A) Depth stop assembly (A) Quill rise and full return spring (A)
- Page 16 Illustration and Parts Description Vertical scale Horizontal column Motor yoke locking knob Horizontal column lock Pulley drive belt cover ON/OFF switch shroud Motor Drill column Chuck guard Retaining collar Rise and fall rack Keyless chuck Lever feed handle Crank handle 105112 AC680RD Drill table Lift and shift handles...
- Page 17 Illustration and Parts Description Vertical scale (A) Horizontal column adjusting knob (A) Column pointer (B) Horizontal column clamping handle (B), Motor yoke clamp (C) Turn the horizontal adjusting knob Turn the horizontal adjusting knob Vertical locking pin anti-clockwise to move the column forward clockwise to move the column back Loosen the horizontal column clamping handle (B).
-
Page 18: Changing The Speed
Refer to the (speed select table on page 21) and ascertain the Motor yoke lock belt positions for speed required. Fig 33-34 AC285PD Drive Pulley WARNING! TAKE CARE NOT TO TRAP YOUR FINGERS WHEN REPOSITIONING THE BELT ON THE PULLEYS! Turn the pulleys to check the belts move freely. Tension the... - Page 19 Removing Keyless Chuck 1. Lower the quill to its maximum depth by turning the lever feed handle. While holding the handle turn the depth scale ring (A) fully round and then tighten the butterfly depth stop clamp (B) to lock the quill in position, see fig 37. Fig 37 Depth scale ring 2.
-
Page 20: Maintenance
POWER CABLE HAS BECOME DAMAGED If any servicing (other than the cleaning above) becomes necessary, the unit should be returned to Axminster Tool Centre for repair by one of our qualified electricians. Contact our customer sales department for further assisance on:... -
Page 21: Speed Select Tables
Speed Select Tables (5 Speed) 105105 AC285PD Bench Pillar Drill (12 Speed) 105106 AC315PD Bench Pillar Drill (5 Speed) 105107AC220RD Bench Radial Pillar Drill 105112 AC680RD Floor Radial Pillar Drill... -
Page 22: Drill Speed Material Table
Drill Speed Material Table 5 Speed Spindle Motor 12 Speed Spindle Jockey Pulley Motor Recommended Drill Size per Material Zinc Aluminium Cast Iron Steel Steel Cast Steel Average Guide Wood Plastic Diecast or Brass and Bronze Mild and Stanless and Speed Malleable Carbon... -
Page 23: Troubleshooting
Troubleshooting TROUBLE PROBABLE CAUSE REMEDY 1. Incorrect belt tension 1. Adjust the tension Noisy Operation 2. Dry spindle 2. Lubricate spindle 3. Loose spindle pulley 3. Checking tightness of retaining nut on pulley, and tighten if necessary 4. Loose motor pulley 4. - Page 24 Exploded Diagrams/Lists AC285PD Bench Pillar Drill (ZQJ4113A)
- Page 25 Exploded Diagrams/Lists AC285PD Bench Pillar Drill (ZQJ4113A) DESCRIPTION BOLT M8x16 BASE MOTOR PULLEY COLUMN HEADLESS SET SCREW BOLT M8X20 PULLEY COVER TABLE BRACKET WASHER SQUARE TABLE SCREW M6X10 BOLT M12x25 SPINDLE PULLEY CLAMPING LEVER HEADLESS SET SCREW BODY RETAIN RING...
- Page 26 Exploded Diagrams/Lists AC315PD Bench Pillar Drill (ZQJ4116Q)
- Page 27 Exploded Diagrams/Lists AC315PD Bench Pillar Drill (ZQJ4116Q) DESCRIPTION HEADLESS SET SCREW BASE SLIDE BAR BOLT BOLT SCREW COLUMN SLIDE BAR RACK RING INSTRUCTION MANUAL HEADLESS SET SCREW CHUCK KEY RACK SPRING MOUNTING ARM BRACKET SPRING SEAT WORM GEAR PLASTIC JAM NUT GEAR SCREW SHAFT...
- Page 28 Exploded Diagrams/Lists AC220RD Bench Radial Drill (ZQJ3116) AC680RD Floor Radial Drill (ZQJ3116A)
- Page 29 Exploded Diagrams/Lists AC220RD Bench Radial Drill (ZQJ3116) AC680RD Floor Radial Drill (ZQJ3116A) DESCRIPTION BRACKET CHUCK TENSION ADJUSTMENT BAR LOWER SPINDLE ASSEMBLY HEX HEAD BOLT SPINDLE 8MM FLAT WASHER 6202LL BALL BEARING MOTOR MOUNT PLATE QUILL 10MM FLAT WASHER 6201LL BALL BEARING 10MM LOCK WASHER RETAINING RING HEX NUT...
- Page 30 Exploded Diagrams/Lists AC220RD Bench Radial Drill (ZQJ3116) DESCRIPTION BASE COLUMN ASSEMBLY 8-1.25 X 20MM SOCKET HEAD BOLT RACK 6-1.0 X 10MM SET SCREW CRANK HANDLE RACK RETAINING RING TABLE BRACKET ASSEMBLY (INCL. REF. NOS. 12 AND 21) WORM AND PINION GEAR SET WORM GEAR PINION GEAR AND SHAFT LOCKING HANDLE...
- Page 31 Exploded Diagrams/Lists AC680RD Floor Radial Drill (ZQJ3116A) DESCRIPTION BASE COLUMN ASSEMBLY 8-1.25 X 20MM SOCKET HEAD BOLT RACK 6-1.0 X 10MM SET SCREW CRANK HANDLE RACK RETAINING RING TABLE BRACKET ASSEMBLY (INCL. REF. NOS. 12 AND 21) WORM AND PINION GEAR SET WORM GEAR PINION GEAR AND SHAFT LOCKING HANDLE...
-
Page 32: Wiring Diagram
Wiring Diagram... - Page 33 Notes...
- Page 34 Notes...
- Page 35 Notes...
- Page 36 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminster.co.uk/3years...