Weslo Pursuit CT 2.4 User Manual

Hide thumbs

Table Of Contents

www.weslo.com

Model No. WLEX81214C.0

Serial No.

Write the serial number in the space

above for reference.

Serial

Number

Decal

ACTIVATE YOUR

WARRANTY

To register your product and

activate your warranty today,

go to www.iconservice.ca.

CUSTOMER SERVICE

Call toll-free 1-888- 936-4266

Mon.–Fri. 7:30 a.m.–4:30 p.m. ET

(excluding holidays)

or email us at

customerservice@iconcanada.ca

Please do not contact the store.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

USER'S MANUAL

Table of Contents

Summary of Contents for Weslo Pursuit CT 2.4

Page 1 USER’S MANUAL Model No. WLEX81214C.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal ACTIVATE YOUR WARRANTY To register your product and activate your warranty today, go to www.iconservice.ca. CUSTOMER SERVICE Call toll-free 1-888- 936-4266 Mon.–Fri.
Page 2: Table Of Contents
Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. WESLO is a registered trademark of ICON Health & Fitness, Inc.
Page 3: Important Precautions
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your exercise bike before using your exercise bike. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
Page 5: Before You Begin
The endurance, and toning the body. The PURSUIT CT 2.4 model number and the location of the serial number exercise bike provides a selection of features designed decal are shown on the front cover of this manual.
Page 6: Part Identification Chart
PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.
Page 7: Assembly
ASSEMBLY • Assembly requires two persons. • In addition to the included tool(s), assembly requires the following tools: • Place all parts in a cleared area and remove the one Phillips screwdriver packing materials. Do not dispose of the packing materials until you ﬁ...
Page 8 2. Identify the Rear Stabilizer (39), which has Leveling Caps (40). Attach the Rear Stabilizer (39) to the Frame (23) with two M8 x 65mm Carriage Bolts (18), two M8 Curved Washers (17), and two M8 Acorn Nuts (42); start both Carriage Bolts, and then tighten the Acorn Nuts.
Page 9 4. Attach the Seat (45) to the Seat Post (44) with three M8 Locknuts (9) and three M8 Large Washers (49); start all the Locknuts, and then tighten them. 5. Loosen and remove the Seat Knob (24). Next, insert the Seat Post (44) into the Seat Post Sleeve (26), and then insert the Seat Knob (24) into the Frame (23) and into an adjustment hole in the Seat Post.
Page 10 6. While a second person holds the Upright (35) near the Frame (23), connect the Upright Wire (36) to the Reed Switch Wire (7). Next, push the Lower Resistance Cable (34) upward into the Upright (35), and then pull the end of the Lower Resistance Cable out of the indicated hole.
Page 11 8. Connect the Resistance Cable (37) to the Lower Resistance Cable (34) in the following way: Avoid pinching See drawing A. Pull upward on the metal the cable bracket (A) on the Lower Resistance Cable (34), and insert the tip of the Resistance Cable (37) into the wire clip inside the metal bracket.
Page 12 10. Attach the Water Bottle Holder (21) to the Upright (35) with two M5 x 20mm Screws (27); start both Screws, and then tighten them. 11. The Console (1) can use two AA batteries (not included); alkaline batteries are recommended. Do not use old and new batteries together or alkaline, standard, and rechargeable batter- ies together.
Page 13 12. While a second person holds the Console (1) near the Upright (35), connect the wire on the Console to the Upright Wire (36). Tip: Avoid pinching the wires. Attach the Console (1) to the Upright (35) with four M5 x 10mm Screws (2);...
Page 14: How To Use The Exercise Bike
HOW TO USE THE EXERCISE BIKE HOW TO ADJUST THE SEAT POST HOW TO ADJUST THE PEDALING RESISTANCE To increase the For effective exercise, the seat should be at the proper resistance of the height. As you pedal, there should be a slight bend in your knees when the pedals are in the lowest position.
Page 15 CONSOLE DIAGRAM FEATURES OF THE CONSOLE The easy-to-use console features five modes that provide instant exercise feedback during your workouts. Scan (SCAN)—This mode displays the time, speed, distance, and calorie modes, for a few seconds each, in a repeating cycle. Time (TMR)—This mode displays the elapsed time.
Page 16 HOW TO USE THE CONSOLE 3. Begin pedaling and follow your progress with the displays. Make sure that batteries (not included) are installed in the console (see assembly step 11 on page 12). If Scan mode—To select the scan mode, press the there is a sheet of plastic on the console, remove the MODE button repeatedly until the word SCAN plastic.
Page 17: Maintenance And Troubleshooting
MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Locate the Reed Switch (7). Turn the Crank (3) until a Magnet (12) is aligned with the Reed Switch. Inspect and tighten all parts of the exercise bike regularly. Replace any worn parts immediately. To clean the exercise bike, use a damp cloth and a small amount of mild detergent.
Page 18 HOW TO ADJUST THE DRIVE BELT If you can feel the pedals slip while you are pedaling, even when the resistance is at the highest level, the drive belt may need to be adjusted. To adjust the drive belt, you must first remove the right pedal and the right shield as described below.
Page 19: Exercise Guidelines
EXERCISE GUIDELINES Aerobic Exercise—If your goal is to strengthen your WARNING: cardiovascular system, you must perform aerobic Before beginning this exercise, which is activity that requires large amounts or any exercise program, consult your physi- of oxygen for prolonged periods of time. For aerobic cian.
Page 20 SUGGESTED STRETCHES The correct form for several basic stretches is shown at the right. Move slowly as you stretch; never bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible.
Page 21 NOTES...
Page 22: Part List
PART LIST Model No. WLEX81214C.0 R1115A Key No. Qty. Description Key No. Qty. Description Console M5 x 20mm Screw M5 x 10mm Screw Clamp Crank/Pulley Left Shield M4 Washer Right Shield Drive Belt M4 x 50mm Screw Eddy Mechanism 3/16" x 3/4" Screw Reed Switch/Wire Right Pedal/Strap Left Pedal/Strap...
Page 23: Exploded Drawing
EXPLODED DRAWING Model No. WLEX81214C.0 R1115A...
Page 24: Ordering Replacement Parts
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us: • the model number and serial number of the product (see the front cover of this manual) •...

This manual is also suitable for:

Wlex81214c.0

Weslo Pursuit CT 2.4 User Manual

Table of Contents

Related Manuals for Weslo Pursuit CT 2.4

Summary of Contents for Weslo Pursuit CT 2.4

This manual is also suitable for:

Table of Contents