Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BluStream HMXL44-KIT V2
Summary of Contents for BluStream HMXL44-KIT V2
- Page 1 4x4 4K HDBaseT™ Matrix - HDCP 2.2 HMXL44-KIT V2 User Manual...
-
Page 2: Table Of Contents
RS-232 and Telnet Commands 15-16 Do not substitute or use any other power supply other than the enclosed unit, or a Blustream approved replace- Infrared Commands 17-18 ment. Do not disassemble either the Trans-... -
Page 3: Introduction
Our Essential 4x4 HDBaseT™ matrix offers unprecedented performance and value for the custom installation market. The HMXL44-KIT V2 is a 4K 4x4 HDCP 2.2 matrix package, delivering HDMI, bi-directional IR and PoH (PoE) up to lengths of 70m over a single CAT cable. - Page 4 Connect to control Zone specific bi-directional RS-232 descriptions 8-12 for further details). processor or Blustream 5v IR receiver. ports – Connect to third party control TCP/IP (RJ45) – Connect to LAN for device to extend RS-232 commands Power port –...
-
Page 5: Control Ports
F. RS-232 (3-pin Phoenix connector) for 2-way RS-232 pass-through to the associated output HDBaseT Receiver *Note - Blustream products use 5V IR hardware. For further details please see page 9 ‘Infrared Distribution’ Blustream HMXL44 V2 Matrix is supplied with all required 5V IR emitters,... -
Page 6: Hdbaset Receiver Options
(30W per channel). The unit has local HDMI 60Hz 4:2:0). and Analogue audio inputs as well as supporting HDMI ARC (Audio Compatible with all Blustream Matrix products. Return Channel) with compatible products. Should you wish to use alternate power amplification the unit has variable analogue outputs. -
Page 7: Matrix Front Panel Controls
HMXL44-KIT V2 USER MANUAL Matrix Front Panel Control Front Panel Display - Input/Output selection The following display shows current source input selection per zone output. To change input selection first press ‘OUTPUT’ button (1-4) Press desired ‘INPUT’ button (1-4) An ‘X’ indicates that the zone output has been turned off. -
Page 8: Audio Breakout
Extracted audio will be concurrent with the corresponding HDMI video output. The HMXL44 V2 analogue outputs include pre-amp line level control allowing you to connect the Blustream matrix directly into a power amplifier for all your multi-room audio needs. - Page 9 The HDBaseT link light will be lit when a CAT cable is connected to the HDBaseT RJ45 output on the Matrix and an active connection is achieved with the Blustream HDBaseT Receiver. Blustream Support department are on hand to assist with signal distribution issues should they arise - please email us at one of the email addresses below.
- Page 10 IMPORTANT: Blustream InfraRed products are all 5V and NOT compatible with alternative manufacturers InfraRed solutions. When using third party 12V IR control solutions please use supplied Blustream IRCAB cable for IR conversion. Each Blustream Matrix and HDBaseT receiver is supplied with all necessary IR hardware required and includes: IR Emitter - IR1 &...
- Page 11 HMXL44-KIT V2 USER MANUAL Remote Control Description OUTPUT AND INPUT SELECTION EDID SET UP Selects the zone OUTPUT you wish to The HMXL44 V2 provides a change the source on (Numbers 1 - 4 POWER comprehensive range of EDID settings.
-
Page 12: Edid Control
EDID hand shaking thus making switching quicker and more reliable. Configuration of Matrix EDID settings can be acheived in one of five ways:- Using Matrix PC Software (See ‘Blustream Matrix Software Guide’ for further details available at www. blustream.co.uk) Using Matrix web browser interface (See ‘Blustream Web Browser Interface Guide’... - Page 13 HMXL44-KIT V2 USER MANUAL ZONE 01 ZONE 02 ZONE 03 ZONE 04 SOURCE 01 SOURCE 02 SOURCE 03 SOURCE 04 70m max contact support@blustream.co.uk / support@blustream.com.au...
-
Page 14: Specifications
HMXL44-KIT V2 USER MANUAL Specifications • Video Input Connectors: 4x HDMI Type A, 19-pin, female • Video Output Connectors: 4x HDMI Type A, 19-pin, female, 4x HDBaseT™ RJ45 connector • Audio Output Connectors: 4x 3.5mm Analogue audio stereo jack •... -
Page 15: Rs-232 And Telnet Commands
RS232 and Telnet Commands The Blustream HMXL44 V2 can be controlled via serial and TCP/IP. The following pages list all available serial commands for the The Blustream HMXL44 V2 can be controlled via serial and TCP/IP. The following pages list all available serial commands for the HMXL44 V2 Matrix. -
Page 16: Rs-232 And Telnet Commands
HMXL44-KIT V2 USER MANUAL HMXL44AB V2 USER MANUAL RS232 and Telnet Commands (Continued) RS232 and Telnet Commands (Continued) RS232 Command Description OUTxxFRyy Set OUTPUT:xx From INPUT:yy Copy EDID from output (yy) to input (xx) EDIDxxCPyy Both yy & xx can be set individually (01-08) or as ALL (00) - Page 17 HMXL44-KIT V2 USER MANUAL 4x4 Matrix IR Database 4X4 MATRIX PRODUCTS NEC IR: CUSTOMER CODE 1898 HEX IR 0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016...
- Page 18 HMXL44-KIT V2 USER MANUAL 4x4 Matrix IR Database 0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016...
-
Page 19: Web Browser Interface
IP address. You can configure the network settings of the Matrix using either the Web Browser Interface (Blustream Matrix products are shipped with the network set to DHCP) or using the Blustream PC Configuration Software (downloadable from the Blustream Drivers & Protocols link on the product web page). - Page 20 www.blustream.com.au...
Need help?
Do you have a question about the HMXL44-KIT V2 and is the answer not in the manual?
Questions and answers