Dremel 200 Original Instruction page 22

ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Rated power . . . . . . . . . . . . 125 W
Voltage Rating
. . . . . . . . . . . . . . .
Collet Capacity
. . . . . . . . . . . . . . .
Rated speed (n) . . . . . . . . . . 35000 min
Class II construction . . . . . . . Double insulated construction tools
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving and
engraving, cutting, cleaning and polishing.
PICTURE 1
PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Attachment interface
E. Shaft Lock Button
F. Ventilation openings
G. Hanger
H. Power cord
I. On/Off Switch and Speed Dial
J. Brush cover (one each side)
230-240 V, 50-60 Hz
0,8mm, 1,6mm, 2,4mm, 3,2mm
-1
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identified by the rings on the back of the collet.
PICTURE 3
K. 3,2 mm Collet without ring
L. 2,4 mm Collet with three rings
M. 1,6 mm Collet with two rings
N. 0,8 mm Collet with one ring
Always use the collet that matches the shank size of the accessory
you plan to use. Do not force a larger diameter shank into a smaller
collet.
CHANGING COLLETS
PICTURE 4
O. Shaft Lock Button
P. Collet Wrench
Q. To tighten
R. To loosen
S. Collet Nut
1. Press the shaft lock button, hold down and rotate the shaft
by hand until it engages the shaft. Do not engage the shaft
lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut finger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
PICTURE 5/6
T. Shaft Lock Button
1. Press the shaft lock button and rotate the shaft by hand
until it engages the shaft lock. Do not engage the shaft lock
button while multitool is running.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, finger tighten the collet
nut until the bit or accessory shank is gripped by the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
22
COLLETS