Panel Calibration; Backlight Setting - Fujitsu UTY-RNRYZ1 Operating Manual

When the item to be set is touched, the display switches
to each setting screen. When each setting is complete
or canceled, the display returns to this screen. When
[Back] is touched, the display returns to the "Main Menu"
screen.

3-7-1 Panel Calibration

(1) Touch the [Panel Calibration] on the "Preference"
screen.
(2) "Panel Calibration" screen is displayed. Touch the [Start]
on the "Panel Calibration" screen.
(1)
Preference
Panel Backlight
Calibration Setting
Contrast
Back
(3) Touch the center of the [+] mark.
(4) The [+] mark is displayed at the bottom left side of the
screen. Touch the center of this mark.
(3)
Touch the center of the [+] mark.
(5) The [+] mark is displayed at
the bottom right side of the
screen. Touch the center of
this mark.
(6) The [+] marks are sequentially displayed at 3 points on
the screen again. Touch the center of each mark.
For confirmation, touch the 3 [+] marks
again.
Touch the center of the [+] mark.
For confirmation, touch the 3 [+] marks
again.
Touch the center of the [+] mark.
(7) When calibration was successful, the display returns to
the "Preference" screen.
If the Panel Calibration has failed
Screen shows that calibration
failed. To repeat calibration,
touch [Retry] and repeat (2) to
(6).
(2)
Panel Calibration
Calibrate the touch panel screen by touching
the 3 [+] marks displayed on the screen.
Press the [Start] button to start the
calibration.
Cancel Start
(4)
Touch the center of the [+] mark.
Touch the center of the [+] mark.
For confirmation, touch the 3 [+] marks
again.
Touch the center of the [+] mark.
Calibration failed. If you repeat it, press the
[Retry] button.
Cancel Retry

3-7-2 Backlight Setting

(1) Touch the [Backlight Setting]
on the "Preference" screen.
Enable or disable the backlight
(2) "Backlight Setting" screen is displayed. Touch the [En-
able/Disable] on the "Backlight Setting" screen.
(3) "Enable/Disable" screen is displayed. Select the [Enable]
or [Disable].
(2)
Backlight Setting
Enable/Disable [Enable]
Automatic Off Time [30s]
Brightness [2]
Cancel OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
Note
When set to "Disable", [Automatic Off Time] and [Bright-
ness] setting are unnecessary.
Set the time until backlight is turned off.
(4) Touch the [Automatic Off Time] on the "Backlight Set-
ting" screen.
(5) "Automatic Off Time" screen is displayed. Select the [60
sec.] or [30 sec.].
(4)
Backlight Setting
Enable/Disable [Enable]
Automatic Off Time [30s]
Brightness [2]
Cancel OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
Adjust the brightness of Backlight
(6) Touch the [Brightness] on the "Backlight Setting" screen.
(7) "Brightness" screen is displayed. Adjust the brightness
with the [ ] or [ ].
(6)
Backlight Setting
Enable/Disable [Enable]
Automatic Off Time [30s]
Brightness [2]
Cancel OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
Apply the setting.
(8) After setting is complete,
touch the [OK] on the "Back-
light Setting" screen.
After the setting change is
displayed, the display returns
to the "Preference" screen.
Preference
Panel Backlight
Calibration Setting
Contrast
Back
(3)
Enable/Disable
Enable
Disable
Cancel OK
(Cannot be set) Go to (8).
(5)
Automatic Off Time
60s
30s
Cancel OK
(7)
Brightness Brightness
3
2
1
Cancel Cancel OK OK
Backlight Setting
Enable/Disable [Enable]
Automatic Off Time [30s]
Brightness [2]
Cancel OK
En-16