Kenwood CK 232 DFA Instructions For Use - Installation Advice
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Cookers
  5. CK 232 DFA
  6. Instructions for use - installation advice

Kenwood CK 232 DFA Instructions For Use - Installation Advice

Gas cooker with electric double oven
Hide thumbs
Table of Contents

Advertisement

Quick Links

GAS COOKER with
ELECTRIC DOUBLE
OVEN
CK 232 DFA
model
Instructions for use - Installation advice
GB
Before operating this cooker,
please read these instructions carefully
1

Advertisement

Table of Contents
loading

Related Manuals for Kenwood CK 232 DFA

Summary of Contents for Kenwood CK 232 DFA

  • Page 1 GAS COOKER with ELECTRIC DOUBLE OVEN CK 232 DFA model Instructions for use - Installation advice Before operating this cooker, please read these instructions carefully...

  • Page 2: Table Of Contents

    CONTENTS Page Number Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Safeguards &...

  • Page 3: Introduction

    Dear Customer, Thank you for purchasing the Kenwood CK 232 DFA double oven dual fuel cooker . The safety precautions and recommendations listed below are for your own safety and that of others . They will also provide a means by which to make full use of the features offered by your appliance .

  • Page 4: Important Safeguards & Recommendations

    IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS IMPORTANT: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domestic environment i.e.
  • Page 5 • Do not touch the appliance with wet or damp hands (or feet) . • Do not use the appliance whilst in bare feet . • If you should decide not to use this appliance any longer (or decide to substitute another model), before disposing of it, it is recommended that it be made inoperative in an appropriate manner in accordance to health and environmental protection regulations, ensuring in particular...
  • Page 6 • WARNING: Danger of fire: do not store items on the cooking surfaces. • WARNING: When correctly installed, your product meets all safety requirements laid down for this type of product category . However special care should be taken around the rear or the underneath of the appliance as these areas are not designed or intended to be touched and may contain sharp or rough edges, that may cause injury .
  • Page 7 ENERGY LABELLING/ECODESIGN • Commission delegated regulation (EU) No 65/2014 (supplementing Directive 2010/30/EU of the European Parliament and of the Council) . • Commission regulation (EU) No 66/2014 (implementing Directive 2009/125/EC of the European Parliament and of the Council) . Reference to the measurement and calculation methods used to establish compliance with the above requirements: •...

  • Page 8: Cooking Hob

    1 - COOKING HOB Fig . 1 .1 GAS BURNERS Auxiliary burner (A) 1,00 kW Semi-rapid burner (SR) 1,75 kW Triple-ring burner (TR) 3,50 kW Notes: • The electric ignition is incorporated in the knobs . • The appliance has a safety valve system fitted, the flow of gas will be stopped if and when the flame should accidentally go out.

  • Page 9: Control Panel

    2 - CONTROL PANEL Fig . 2 .1 Controls description Front right burner control knob Rear right burner control knob Rear left burner control knob Front left burner control knob Conventional oven temperature knob (Top oven) Conventional oven function selector knob (Top oven) Fan oven switch and temperature knob (Bottom main oven) Electronic programmer (main oven only) Pilot lamps:...

  • Page 10: Use Of The Hob Burners

    3 - USE OF THE HOB BURNERS GAS BURNERS Gas flow to the burners is adjusted by turning the knobs (illustrated in fig. 3.1) which control the safety valves . Turning the knob, so that the indicator line points to the symbols printed on the panel, achieves the following functions: - symbol closed valve...
  • Page 11 LIGHTING THE BURNERS CHOICE OF THE BURNER ignite burner, following On the control panel, near every knob instructions are to be followed: there is a diagram that indicates which burner is controlled by that knob . Press in the corresponding knob and The suitable burner must be chosen turn counter-clockwise (fig.
  • Page 12 CORRECT USE OF THE TRIPLE-RING BURNER Only flat bottom pans of the correct size are to be placed on the pan support above the Triple-ring burner . When using a WOK, the supplied wok stand must be placed onto the pan stand to avoid any faulty operation of the triple-ring burner (fig.

  • Page 13: Top Conventional Electric Oven

    4 - TOP CONVENTIONAL ELECTRIC OVEN WARNING: Attention: The oven door becomes The door is hot, use the handle. very hot during operation. Keep children away. ATTENTION - MOST IMPORTANT Pay special attention not to touch the hot heating element inside the oven GENERAL FEATURES cavity.
  • Page 14 TEMPERATURE KNOB (fig. 4.2) This only sets the cooking temperature but does not switch the oven on . Rotate clockwise until the required temperature is reached (from 50°C to the maximum position, 250°C) . The light above the knob will illuminate when the oven is switched on and turns off when the oven reaches the correct temperature .

  • Page 15: Bottom Main Oven

    5 - BOTTOM MAIN OVEN Attention: The oven door becomes very hot during operation. Keep children away. SWITCH TEMPERATURE SELECTOR Turn the selector knob (fig. 5.1) to the required function . OFF - as per fig. 5.1 The oven light is switched on . The fan operates without the heating element, this function Fig .

  • Page 16: Cooking Guide

    6 - OVEN TEMPERATURE GUIDE Electric oven temperature Cooking process Oven heat Gas mark °C °F Keeping food hot, very cool ½ milk puddings Egg custards cool Rich fruit cakes, cool braising Low temperature moderate roasting, shortbread Victoria sandwich, plain fruit cake, moderate baked fish Small cakes, choux...

  • Page 17: Electronic Programmer

    ELECTRONIC PROGRAMMER (BOTTOM MAIN OVEN ONLY) The electronic programmer is a device which groups together the following functions: • 24 hours clock with illuminated display • Timer (up to 23 hours and 59 minutes) • Program for automatic oven cooking (bottom main oven only) •...
  • Page 18 SETTING TIME OF DAY MANUAL OPERATION (fig. 7.2) The programmer is provided with an To use the oven manually, i .e . without the electronic clock with luminous figures programmer, you must cancel the flashing showing the hour and minutes . A by pressing the two buttons The first time the oven is connected up to simultaneously (the letter A will go out and...
  • Page 19 MINUTE MINDER AUDIBLE SIGNAL The minute counter function consists The audible signal sounds at the end simply of an acoustic signal which can be of a minute minder cycle or of a cooking set for a maximum of 23 hours 59 minutes . programme for a period of 7 minute .
  • Page 20 SEMI - AUTOMATIC COOKING The oven will come on immediately and when the set time or programmed end of This automatically switches the oven off cooking time expires, it will automatically after the required cooking time . There are switch off . two methods of semi-automatic cooking: During cooking the letter A and the symbol remains on;...
  • Page 21 AUTOMATIC COOKING Set the cooking temperature and function via the function selector and To cook in the oven in automatic mode thermostat knob (see specific chapters). follow the instructions below: The oven is now programmed and Set the cooking time everything will work automatically;...
  • Page 22 IMPORTANT – MAIN OVEN NOT WORKING If the main Oven is not working, it may have been accidently set to “AUTOMATIC” or the power to the appliance was interrupted . If the Timer is showing the letter “A” as below or the time of day is flashing, the Oven may not turn on or be delayed in its operation.

  • Page 23: Cleaning And Maintenance

    8 - CLEANING AND MAINTENANCE GENERAL ADVICE CLEANING • Before you begin cleaning, you Stainless steel hob: Spillage on • must ensure that the appliance is the hob can usually be removed by switched off at the cooker switch. a damp soapy cloth . More obstinate •...
  • Page 24 Inside of oven: The oven should BURNERS AND PAN SUPPORTS • always be cleaned after use when it These parts can be removed and cleaned has cooled down . The cavity should be as indicated previously . cleaned using a mild detergent solution After cleaning, the burners and their flame and warm water .
  • Page 25 Fig . 8 .1 Fig . 8 .2 Fig . 8 .3 Fig . 8 .4 Fig . 8 .5...
  • Page 26 WIRE RACKS • Assemble the wire racks to the oven walls using the screws (2 screws figs. 8.6a, 8.6b). • Slide in, on the guides, the shelf and the tray (figs. 8.7a, 8.7b). The shelf must be fitted so that the safety notch, which stops it sliding out, faces the inside of the oven;...
  • Page 27 REPLACING THE OVEN LAMP WARNING: Ensure the appliance is switched off and disconnected from the electrical power supply before replacing the lamp to avoid the possibility of WRONG electric shock. • Let the oven cavity and the heating elements to cool down . •...
  • Page 28 TOP OVEN DOOR REMOVING THE OVEN DOOR The oven door can easily be removed as follows: • Open the door to the full extent (fig. 8 .9a) . • Open the lever “A” completely on the left and right hinges (fig. 8.9b). •...
  • Page 29 TOP OVEN DOOR CLEANING THE PANES OF GLASS The oven door is fitted with no. 2 panes: • no . 1 outside; • no . 1 inner; To clean the panes on both sides it is necessary to remove the inner pane as follows .
  • Page 30 TOP OVEN DOOR REPLACING THE INNER PANE OF GLASS Make sure the door is locked open (see fig. 8.9c). Replace the inner pane: • Check that the four rubber pads are in Fig . 8 .11a place (“D” in fig. 8.11a). •...
  • Page 31 LOWER OVEN DOOR Note: The oven door should only be removed by an authorised service agent . Removal oven door nonauthorised person will invalidate the guarantee . REMOVING INNER PANE GLASS IMPORTANT WARNING: BEFORE REMOVING THE INNER GLASS OF THIS DOOR IS IT IS MANDATORY THAT THE TOP SMALL GRILL DOOR IS REMOVED When removing and replacing the inner...
  • Page 32 REPLACING THE INNER PANE OF GLASS To replace the inner pane of the door operate as follows: • Check that the four rubber pads are in place (“D” in fig. 8.13a). • Check that you are holding the pane the correct way . You should be able to read the wording on it as it faces you .

  • Page 33: Advice For The Installer

    Advice for the installer IMPORTANT • The appliance is designed and approved for domestic use only and should not be installed in a commercial, semi commercial or communal environment . Your product will not be guaranteed if installed in any of the above environments and could affect any third party or public liability insurances you may have.

  • Page 34: Installation

    9 - INSTALLATION This cooker has class “2/1” overheating protection so that it can be installed next to a cabinet. If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a gap of at least 200 mm must be left between the side of the cooker and the furniture . The walls and kitchen furniture surrounding the appliance must be made of non-flammable material .
  • Page 35 ANTI-TILT BRACKET Important! To restrain the appliance and prevent it tipping accidentally, the anti-tilt bracket supplied must be fitted according to the instructions below. To fit the anti-tilt bracket: After you have located where the cooker is to be positioned, mark on the wall and on the floor the place where the four screws of the anti-tilt bracket have to be fitted.

  • Page 36: Provision For Ventilation

    PROVISION FOR VENTILATION • The appliance should be installed into a room or space with an air supply in accordance with the current version of BS 5440-2: 2000 . • For rooms with a volume of less than 5m - permanent ventilation of 100 cm free area must be provided .

  • Page 37: Gas Installation

    10 - GAS INSTALLATION IMPORTANT NOTE This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance) . • Appliances supplied for use on NATURAL GAS are adjusted for this gas only and cannot be used on any other gas (LPG) without modification.
  • Page 38 RESTRAINING CHAIN Fig . 10 .1 Chain security holes Cooker Back of the cooker Rear wall Installation to Natural Gas Installation to Natural Gas must conform to the Code of Practice, etc . The supply pressure for Natural Gas is 20 mbar . The installation must conform to the relevant British/European Standards .
  • Page 39 Notes: • Flexible hoses can be used where the sited ambient temperature of the hose does not exceed 70°C. These hoses must be manufactured in accordance with BS669 part 1 or EN 14800 and be of the correct construction for the type of gas being used.
  • Page 40 Fig . 10 .3 Cooker manifold (gas inlet pipe) Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) male Fibre washer ( * ) 1/2” G cylindrical (ISO 228-1) female Connector ( * ) 1/2” BSP female Supplied with the appliance in a separate kit IMPORTANT PRESCRIPTIONS FOR GAS CONNECTION...
  • Page 41 CONVERSION TO NATURAL GAS OR TO LPG REPLACEMENT OF THE INJECTORS Auxiliary and If the injectors are not supplied they can Semi-rapid be obtained from the After-Sales Service. burners Select the injectors to be replaced according to the “Table for the choice of the injectors”...
  • Page 42 TABLE FOR THE CHOICE OF THE INJECTORS Cat: 2H3+ G30 28-30 Natural Gas Nominal Reduced mbar G20 20 mbar G31 37 mbar BURNERS power power [kW] [kW] Ø Ø injector injector [1/100 mm] [1/100 mm] Auxiliary (A) 1,00 0,30 72 (X) Semi-rapid (SR) 1,75 0,45...

  • Page 43: Electrical Section

    11 - ELECTRICAL INSTALLATION IMPORTANT: The appliance must be installed in accordance with the manufacturer’s instructions. Incorrect installation, for which the manufacturer accepts no responsibility, may cause damage to persons, animals and property. The connection of the appliance to earth is mandatory. The manufacturer declines all responsibility for any inconvenience resulting from the inobservance of this condition.
  • Page 44 ELECTRICAL FEEDER CABLE CONNECTION WARNING: The power supply cable must be connected only by an authorised service agent in order to avoid a hazard. If the power supply cable is damaged, it must be replaced only by an authorised service agent in order to avoid a hazard. To connect the supply cable: •...
  • Page 45 12 - GUARANTEE Your new “KENWOOD” product comes with 12-month guarantee covering all parts and labour . If your appliance proves to be defective as a result of faulty materials or workmanship during the guarantee period, these parts will be repaired or replaced free of charge .
  • Page 48 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet . The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances .

Table of Contents